From ec9653b8476bf526dde7bdefbc2be6b7aaa34db7 Mon Sep 17 00:00:00 2001 From: Simon Arlott Date: Sat, 26 May 2012 01:04:43 -0600 Subject: ARM: add infra-structure for BCM2835 and Raspberry Pi The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic support for this SoC. http://www.broadcom.com/products/BCM2835 http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Note that the documentation in the latter .pdf assumes the MMU setup that's used on the "VideoCore" companion processor, and does not document physical peripheral addresses. Subtract 0x5e000000 to obtain the physical addresses. This is accounted for by the ranges property in the /soc node in the device tree. The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a minimal device tree for this board; enough to see some very early kernel boot messages through earlyprintk. However, this patch does not yet provide a useful booting system. http://www.raspberrypi.org/. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split from 3-4 months ago, and significantly stripped down and modified since. Signed-off-by: Chris Boot Signed-off-by: Simon Arlott Signed-off-by: Dom Cobley Signed-off-by: Dom Cobley Signed-off-by: Stephen Warren Acked-by: Arnd Bergmann --- Documentation/devicetree/bindings/arm/bcm2835.txt | 8 ++++++++ Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 2 files changed, 9 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/bcm2835.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/arm/bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm2835.txt new file mode 100644 index 000000000000..ac683480c486 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm2835.txt @@ -0,0 +1,8 @@ +Broadcom BCM2835 device tree bindings +------------------------------------------- + +Boards with the BCM2835 SoC shall have the following properties: + +Required root node property: + +compatible = "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index db4d3af3643c..4f293e5571f0 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -10,6 +10,7 @@ apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. atmel Atmel Corporation bosch Bosch Sensortec GmbH +brcm Broadcom Corporation cavium Cavium, Inc. chrp Common Hardware Reference Platform cortina Cortina Systems, Inc. -- cgit From 89214f009c1d38568456dcf997d93977928fe2c3 Mon Sep 17 00:00:00 2001 From: Simon Arlott Date: Wed, 12 Sep 2012 19:57:26 -0600 Subject: ARM: bcm2835: add interrupt controller driver The BCM2835 contains a custom interrupt controller, which supports 72 interrupt sources using a 2-level register scheme. The interrupt controller, or the HW block containing it, is referred to occasionally as "armctrl" in the SoC documentation, hence the symbol naming in the code. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split as of 2012/09/08, and modified as follows: * s/bcm2708/bcm2835/. * Modified device tree vendor prefix. * Moved implementation to drivers/irchip/. * Added devicetree documentation, and hence removed list of IRQs from bcm2835.dtsi. * Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce the size of the hwirq space, and pass the total size of the hwirq space to irq_domain_add_linear(), rather than just the number of valid hwirqs; the two are different due to the hwirq space being sparse. * Added the interrupt controller DT node to the top-level of the DT, rather than nesting it inside a /axi node. Hence, changed the reg value since /axi had a ranges property. This seems simpler to me, but I'm not sure if everyone will like this change or not. * Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence removing the need to patch include/linux/irqdomain.h or kernel/irq/irqdomain.c. * Simplified armctrl_of_init() using of_iomap(). * Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros. * Renamed armctrl_handle_irq() to prevent possible symbol clashes. * Made armctrl_of_init() static. * Removed comment "Each bank is registered as a separate interrupt controller" since this is no longer true. * Removed FSF address from license header. * Added my name to copyright header. Signed-off-by: Chris Boot Signed-off-by: Simon Arlott Signed-off-by: Dom Cobley Signed-off-by: Dom Cobley Signed-off-by: Stephen Warren Acked-by: Arnd Bergmann --- .../brcm,bcm2835-armctrl-ic.txt | 110 +++++++++++++++++++++ 1 file changed, 110 insertions(+) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt new file mode 100644 index 000000000000..548892c08c59 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -0,0 +1,110 @@ +BCM2835 Top-Level ("ARMCTRL") Interrupt Controller + +The BCM2835 contains a custom top-level interrupt controller, which supports +72 interrupt sources using a 2-level register scheme. The interrupt +controller, or the HW block containing it, is referred to occasionally +as "armctrl" in the SoC documentation, hence naming of this binding. + +Required properties: + +- compatible : should be "brcm,bcm2835-armctrl-ic.txt" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. + + The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic + pending" register, or 1/2 respectively for interrupts in the "IRQ pending + 1/2" register. + + The 2nd cell contains the interrupt number within the bank. Valid values + are 0..7 for bank 0, and 0..31 for bank 1. + +The interrupt sources are as follows: + +Bank 0: +0: ARM_TIMER +1: ARM_MAILBOX +2: ARM_DOORBELL_0 +3: ARM_DOORBELL_1 +4: VPU0_HALTED +5: VPU1_HALTED +6: ILLEGAL_TYPE0 +7: ILLEGAL_TYPE1 + +Bank 1: +0: TIMER0 +1: TIMER1 +2: TIMER2 +3: TIMER3 +4: CODEC0 +5: CODEC1 +6: CODEC2 +7: VC_JPEG +8: ISP +9: VC_USB +10: VC_3D +11: TRANSPOSER +12: MULTICORESYNC0 +13: MULTICORESYNC1 +14: MULTICORESYNC2 +15: MULTICORESYNC3 +16: DMA0 +17: DMA1 +18: VC_DMA2 +19: VC_DMA3 +20: DMA4 +21: DMA5 +22: DMA6 +23: DMA7 +24: DMA8 +25: DMA9 +26: DMA10 +27: DMA11 +28: DMA12 +29: AUX +30: ARM +31: VPUDMA + +Bank 2: +0: HOSTPORT +1: VIDEOSCALER +2: CCP2TX +3: SDC +4: DSI0 +5: AVE +6: CAM0 +7: CAM1 +8: HDMI0 +9: HDMI1 +10: PIXELVALVE1 +11: I2CSPISLV +12: DSI1 +13: PWA0 +14: PWA1 +15: CPR +16: SMI +17: GPIO0 +18: GPIO1 +19: GPIO2 +20: GPIO3 +21: VC_I2C +22: VC_SPI +23: VC_I2SPCM +24: VC_SDIO +25: VC_UART +26: SLIMBUS +27: VEC +28: CPG +29: RNG +30: VC_ARASANSDIO +31: AVSPMON + +Example: + +intc: interrupt-controller { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; +}; -- cgit From ee4af5696720bb5b9de2e3b18be42089bed1e638 Mon Sep 17 00:00:00 2001 From: Simon Arlott Date: Mon, 10 Sep 2012 22:38:35 -0600 Subject: ARM: bcm2835: add system timer The System Timer peripheral provides four 32-bit timer channels and a single 64-bit free running counter. Each channel has an output compare register, which is compared against the 32 least significant bits of the free running counter values, and generates an interrupt. Timer 3 is used as the Linux timer. The BCM2835 also contains an SP804-based timer module. However, it apparently has significant differences from the standard SP804 IP block, and Broadcom's documentation recommends using the system timer instead. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split as of 2012/09/08, and modified as follows: * s/bcm2708/bcm2835/. * Modified device tree vendor prefix. * Moved to drivers/clocksource/. This looks like the desired location for such code now. * Added DT binding docs. * Moved struct sys_timer bcm2835_timer into time.c to encapsulate it more. * Simplified bcm2835_time_init() to find one matching node and operate on it, rather than looping over all matching nodes. This seems more consistent with other clocksource code. * Simplified bcm2835_time_init() using of_iomap(). * Renamed struct bcm2835_timer.index to match_mask to better represent its purpose. * s/printk(PR_INFO/pr_info(/ Signed-off-by: Chris Boot Signed-off-by: Simon Arlott Signed-off-by: Dom Cobley Signed-off-by: Dom Cobley Signed-off-by: Stephen Warren Acked-by: Arnd Bergmann --- .../bindings/timer/brcm,bcm2835-system-timer.txt | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) create mode 100644 Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt b/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt new file mode 100644 index 000000000000..2de21c2acf55 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt @@ -0,0 +1,22 @@ +BCM2835 System Timer + +The System Timer peripheral provides four 32-bit timer channels and a +single 64-bit free running counter. Each channel has an output compare +register, which is compared against the 32 least significant bits of the +free running counter values, and generates an interrupt. + +Required properties: + +- compatible : should be "brcm,bcm2835-system-timer.txt" +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 4 interrupt sinks; one per timer channel. +- clock-frequency : The frequency of the clock that drives the counter, in Hz. + +Example: + +timer { + compatible = "brcm,bcm2835-system-timer"; + reg = <0x7e003000 0x1000>; + interrupts = <1 0>, <1 1>, <1 2>, <1 3>; + clock-frequency = <1000000>; +}; -- cgit