From cabfeaa67843bf8ddda819a6129e20472053310a Mon Sep 17 00:00:00 2001 From: "Cooper Jr., Franklin" Date: Wed, 4 May 2016 13:34:44 -0500 Subject: ARM: OMAP2+: Update GPMC and NAND DT binding documentation Add additional details to the GPMC NAND documentation to clarify what is needed to enable NAND DMA prefetch. Signed-off-by: Franklin S Cooper Jr Acked-by: Rob Herring Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt | 7 ++++++- Documentation/devicetree/bindings/mtd/gpmc-nand.txt | 2 +- 2 files changed, 7 insertions(+), 2 deletions(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt index 21055e210234..c1359f4d48d7 100644 --- a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt @@ -46,6 +46,10 @@ Required properties: 0 maps to GPMC_WAIT0 pin. - gpio-cells: Must be set to 2 +Required properties when using NAND prefetch dma: + - dmas GPMC NAND prefetch dma channel + - dma-names Must be set to "rxtx" + Timing properties for child nodes. All are optional and default to 0. - gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds @@ -137,7 +141,8 @@ Example for an AM33xx board: ti,hwmods = "gpmc"; reg = <0x50000000 0x2000>; interrupts = <100>; - + dmas = <&edma 52 0>; + dma-names = "rxtx"; gpmc,num-cs = <8>; gpmc,num-waitpins = <2>; #address-cells = <2>; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 3ee7e202657c..174f68c26c1b 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -39,7 +39,7 @@ Optional properties: "prefetch-polled" Prefetch polled mode (default) "polled" Polled mode, without prefetch - "prefetch-dma" Prefetch enabled sDMA mode + "prefetch-dma" Prefetch enabled DMA mode "prefetch-irq" Prefetch enabled irq mode - elm_id: use "ti,elm-id" instead -- cgit From decba6d47869f3b5f057df5add52ece92d8e3d22 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Tue, 31 May 2016 10:23:02 -0700 Subject: mtd: brcmnand: Add v7.2 controller support The 7.2 controller differs in a few area compared to its predecssor (7.1): - NAND scrambler, which we are not using just yet - higher ECC levels (up to 120 bits) per 1KB data blocks, also not supported yet - up to 128B OOB This patch adds the necessary code to support such a controller generation and updates the Device Tree binding. Signed-off-by: Florian Fainelli Acked-by: Kamal Dasu Acked-by: Rob Herring Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt index 7066597c9a81..b40f3a492800 100644 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt @@ -27,6 +27,7 @@ Required properties: brcm,brcmnand-v6.2 brcm,brcmnand-v7.0 brcm,brcmnand-v7.1 + brcm,brcmnand-v7.2 brcm,brcmnand - reg : the register start and length for NAND register region. (optional) Flash DMA register range (if present) -- cgit From 5c72ae1dbb5348fd465a472a67d170ea5416fe4f Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Fri, 15 Apr 2016 15:10:31 +0200 Subject: mtd: nand: sunxi: update DT bindings Document dmas and dma-names properties. Signed-off-by: Boris Brezillon Acked-by: Rob Herring Acked-by: Maxime Ripard Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/mtd/sunxi-nand.txt | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 086d6f44c4b9..6fdf8f604b39 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -11,6 +11,10 @@ Required properties: * "ahb" : AHB gating clock * "mod" : nand controller clock +Optional properties: +- dmas : shall reference DMA channel associated to the NAND controller. +- dma-names : shall be "rxtx". + Optional children nodes: Children nodes represent the available nand chips. -- cgit From cac4fcc0d3d8b666e8c7cc738bfdceb814e6e523 Mon Sep 17 00:00:00 2001 From: Jorge Ramirez-Ortiz Date: Tue, 14 Jun 2016 11:50:50 -0400 Subject: mtd: mediatek: device tree bindings for MTK Documentation support for Smart Device Gen1 type of NAND controllers Signed-off-by: Jorge Ramirez-Ortiz Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/mtd/mtk-nand.txt | 160 +++++++++++++++++++++ 1 file changed, 160 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt new file mode 100644 index 000000000000..069c192ed5c2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -0,0 +1,160 @@ +MTK SoCs NAND FLASH controller (NFC) DT binding + +This file documents the device tree bindings for MTK SoCs NAND controllers. +The functional split of the controller requires two drivers to operate: +the nand controller interface driver and the ECC engine driver. + +The hardware description for both devices must be captured as device +tree nodes. + +1) NFC NAND Controller Interface (NFI): +======================================= + +The first part of NFC is NAND Controller Interface (NFI) HW. +Required NFI properties: +- compatible: Should be "mediatek,mtxxxx-nfc". +- reg: Base physical address and size of NFI. +- interrupts: Interrupts of NFI. +- clocks: NFI required clocks. +- clock-names: NFI clocks internal name. +- status: Disabled default. Then set "okay" by platform. +- ecc-engine: Required ECC Engine node. +- #address-cells: NAND chip index, should be 1. +- #size-cells: Should be 0. + +Example: + + nandc: nfi@1100d000 { + compatible = "mediatek,mt2701-nfc"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = ; + clocks = <&pericfg CLK_PERI_NFI>, + <&pericfg CLK_PERI_NFI_PAD>; + clock-names = "nfi_clk", "pad_clk"; + status = "disabled"; + ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + }; + +Platform related properties, should be set in {platform_name}.dts: +- children nodes: NAND chips. + +Children nodes properties: +- reg: Chip Select Signal, default 0. + Set as reg = <0>, <1> when need 2 CS. +Optional: +- nand-on-flash-bbt: Store BBT on NAND Flash. +- nand-ecc-mode: the NAND ecc mode (check driver for supported modes) +- nand-ecc-step-size: Number of data bytes covered by a single ECC step. + valid values: 512 and 1024. + 1024 is recommended for large page NANDs. +- nand-ecc-strength: Number of bits to correct per ECC step. + The valid values that the controller supports are: 4, 6, + 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44, + 48, 52, 56, 60. + The strength should be calculated as follows: + E = (S - F) * 8 / 14 + S = O / (P / Q) + E : nand-ecc-strength. + S : spare size per sector. + F : FDM size, should be in the range [1,8]. + It is used to store free oob data. + O : oob size. + P : page size. + Q : nand-ecc-step-size. + If the result does not match any one of the listed + choices above, please select the smaller valid value from + the list. + (otherwise the driver will do the adjustment at runtime) +- pinctrl-names: Default NAND pin GPIO setting name. +- pinctrl-0: GPIO setting node. + +Example: + &pio { + nand_pins_default: nanddefault { + pins_dat { + pinmux = , + , + , + , + , + , + , + , + ; + input-enable; + drive-strength = ; + bias-pull-up; + }; + + pins_we { + pinmux = ; + drive-strength = ; + bias-pull-up = ; + }; + + pins_ale { + pinmux = ; + drive-strength = ; + bias-pull-down = ; + }; + }; + }; + + &nandc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_default>; + nand@0 { + reg = <0>; + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; + }; + }; + +NAND chip optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + preloader@0 { + label = "pl"; + read-only; + reg = <0x00000000 0x00400000>; + }; + android@0x00400000 { + label = "android"; + reg = <0x00400000 0x12c00000>; + }; + }; + }; + +2) ECC Engine: +============== + +Required BCH properties: +- compatible: Should be "mediatek,mtxxxx-ecc". +- reg: Base physical address and size of ECC. +- interrupts: Interrupts of ECC. +- clocks: ECC required clocks. +- clock-names: ECC clocks internal name. +- status: Disabled default. Then set "okay" by platform. + +Example: + + bch: ecc@1100e000 { + compatible = "mediatek,mt2701-ecc"; + reg = <0 0x1100e000 0 0x1000>; + interrupts = ; + clocks = <&pericfg CLK_PERI_NFI_ECC>; + clock-names = "nfiecc_clk"; + status = "disabled"; + }; -- cgit From 7f657279a6de28573f13420840b2de3e04131d04 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Mon, 20 Jun 2016 12:48:37 +0800 Subject: mtd: nand: sunxi: update DT bindings Document the reset lines Signed-off-by: Icenowy Zheng Acked-by: Maxime Ripard Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/mtd/sunxi-nand.txt | 2 ++ 1 file changed, 2 insertions(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 6fdf8f604b39..f322f56aef74 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -19,6 +19,8 @@ Optional children nodes: Children nodes represent the available nand chips. Optional properties: +- reset : phandle + reset specifier pair +- reset-names : must contain "ahb" - allwinner,rb : shall contain the native Ready/Busy ids. or - rb-gpios : shall contain the gpios used as R/B pins. -- cgit From e523f11141bdc24f65775f0b1fa4a7ed404e68cc Mon Sep 17 00:00:00 2001 From: Jiancheng Xue Date: Tue, 28 Jun 2016 15:48:19 +0800 Subject: mtd: spi-nor: add hisilicon spi-nor flash controller driver Add hisilicon spi-nor flash controller driver Signed-off-by: Binquan Peng Signed-off-by: Jiancheng Xue Acked-by: Rob Herring Reviewed-by: Ezequiel Garcia Reviewed-by: Jagan Teki Reviewed-by: Cyrille Pitchen Signed-off-by: Brian Norris --- .../bindings/mtd/hisilicon,fmc-spi-nor.txt | 24 ++++++++++++++++++++++ 1 file changed, 24 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt new file mode 100644 index 000000000000..74981520d6dd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt @@ -0,0 +1,24 @@ +HiSilicon SPI-NOR Flash Controller + +Required properties: +- compatible : Should be "hisilicon,fmc-spi-nor" and one of the following strings: + "hisilicon,hi3519-spi-nor" +- address-cells : Should be 1. +- size-cells : Should be 0. +- reg : Offset and length of the register set for the controller device. +- reg-names : Must include the following two entries: "control", "memory". +- clocks : handle to spi-nor flash controller clock. + +Example: +spi-nor-controller@10000000 { + compatible = "hisilicon,hi3519-spi-nor", "hisilicon,fmc-spi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10000000 0x1000>, <0x14000000 0x1000000>; + reg-names = "control", "memory"; + clocks = <&clock HI3519_FMC_CLK>; + spi-nor@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + }; +}; -- cgit From 7ddf7c1ea77d10424ae5dfa3c3a4d6a39cdf70a9 Mon Sep 17 00:00:00 2001 From: Cyrille Pitchen Date: Mon, 13 Jun 2016 17:10:25 +0200 Subject: Documentation: atmel-quadspi: add binding file for Atmel QSPI driver This patch documents the DT bindings for the driver of the Atmel QSPI controller embedded inside sama5d2x SoCs. Signed-off-by: Cyrille Pitchen Acked-by: Rob Herring Acked-by: Nicolas Ferre Signed-off-by: Brian Norris --- .../devicetree/bindings/mtd/atmel-quadspi.txt | 32 ++++++++++++++++++++++ 1 file changed, 32 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/atmel-quadspi.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt new file mode 100644 index 000000000000..489807005eda --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt @@ -0,0 +1,32 @@ +* Atmel Quad Serial Peripheral Interface (QSPI) + +Required properties: +- compatible: Should be "atmel,sama5d2-qspi". +- reg: Should contain the locations and lengths of the base registers + and the mapped memory. +- reg-names: Should contain the resource reg names: + - qspi_base: configuration register address space + - qspi_mmap: memory mapped address space +- interrupts: Should contain the interrupt for the device. +- clocks: The phandle of the clock needed by the QSPI controller. +- #address-cells: Should be <1>. +- #size-cells: Should be <0>. + +Example: + +spi@f0020000 { + compatible = "atmel,sama5d2-qspi"; + reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>; + reg-names = "qspi_base", "qspi_mmap"; + interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&spi0_clk>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0_default>; + status = "okay"; + + m25p80@0 { + ... + }; +}; -- cgit From b58439916bdc4c4a5d782e6104e6a4e354bc3022 Mon Sep 17 00:00:00 2001 From: Graham Moore Date: Sat, 4 Jun 2016 02:39:33 +0200 Subject: mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver Add binding document for the Cadence QSPI controller. Signed-off-by: Graham Moore Signed-off-by: Marek Vasut Cc: Alan Tull Cc: Brian Norris Cc: David Woodhouse Cc: Dinh Nguyen Cc: Graham Moore Cc: Vignesh R Cc: Yves Vandervennet Cc: devicetree@vger.kernel.org Acked-by: Rob Herring Signed-off-by: Brian Norris --- .../devicetree/bindings/mtd/cadence-quadspi.txt | 56 ++++++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt new file mode 100644 index 000000000000..f248056da24c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt @@ -0,0 +1,56 @@ +* Cadence Quad SPI controller + +Required properties: +- compatible : Should be "cdns,qspi-nor". +- reg : Contains two entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the QSPI Controller data area. +- interrupts : Unit interrupt specifier for the controller interrupt. +- clocks : phandle to the Quad SPI clock. +- cdns,fifo-depth : Size of the data FIFO in words. +- cdns,fifo-width : Bus width of the data FIFO in bytes. +- cdns,trigger-address : 32-bit indirect AHB trigger address. + +Optional properties: +- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not. + +Optional subnodes: +Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional +custom properties: +- cdns,read-delay : Delay for read capture logic, in clock cycles +- cdns,tshsl-ns : Delay in nanoseconds for the length that the master + mode chip select outputs are de-asserted between + transactions. +- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being + de-activated and the activation of another. +- cdns,tchsh-ns : Delay in nanoseconds between last bit of current + transaction and deasserting the device chip select + (qspi_n_ss_out). +- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low + and first bit transfer. + +Example: + + qspi: spi@ff705000 { + compatible = "cdns,qspi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xff705000 0x1000>, + <0xffa00000 0x1000>; + interrupts = <0 151 4>; + clocks = <&qspi_clk>; + cdns,is-decoded-cs; + cdns,fifo-depth = <128>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x00000000>; + + flash0: n25q00@0 { + ... + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; + }; -- cgit