From e52817faae359ce95c93c2b6eb88b16d4b430181 Mon Sep 17 00:00:00 2001
From: Roger Quadros <rogerq@ti.com>
Date: Mon, 2 Feb 2015 12:21:59 +0200
Subject: extcon: usb-gpio: Introduce gpio usb extcon driver
This driver observes the USB ID pin connected over a GPIO and
updates the USB cable extcon states accordingly.
The existing GPIO extcon driver is not suitable for this purpose
as it needs to be taught to understand USB cable states and it
can't handle more than one cable per instance.
For the USB case we need to handle 2 cable states.
1) USB (attach/detach)
2) USB-HOST (attach/detach)
This driver can be easily updated in the future to handle VBUS
events in case it happens to be available on GPIO for any platform.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
.../devicetree/bindings/extcon/extcon-usb-gpio.txt | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
create mode 100644 Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
(limited to 'Documentation/devicetree')
diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
new file mode 100644
index 000000000000..af0b903de293
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
@@ -0,0 +1,18 @@
+USB GPIO Extcon device
+
+This is a virtual device used to generate USB cable states from the USB ID pin
+connected to a GPIO pin.
+
+Required properties:
+- compatible: Should be "linux,extcon-usb-gpio"
+- id-gpio: gpio for USB ID pin. See gpio binding.
+
+Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below:
+ extcon_usb1 {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+ }
+
+ &omap_dwc3_1 {
+ extcon = <&extcon_usb1>;
+ };
--
cgit
From d0c6ae41d12ad7b2ba271f279936327320b6671c Mon Sep 17 00:00:00 2001
From: Gilad Avidov <gavidov@codeaurora.org>
Date: Wed, 25 Mar 2015 11:37:32 -0600
Subject: spmi: pmic_arb: add support for hw version 2
Qualcomm PMIC Arbiter version-2 changes from version-1 are:
- Some different register offsets.
- New channel register space, one per PMIC peripheral (ppid).
All tx traffic uses these channels.
- New observer register space. All rx trafic uses this space.
- Different command format for spmi command registers.
Reviewed-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
(limited to 'Documentation/devicetree')
diff --git a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
index 715d0998af8e..e16b9b5afc70 100644
--- a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
+++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
@@ -1,6 +1,6 @@
Qualcomm SPMI Controller (PMIC Arbiter)
-The SPMI PMIC Arbiter is found on the Snapdragon 800 Series. It is an SPMI
+The SPMI PMIC Arbiter is found on Snapdragon chipsets. It is an SPMI
controller with wrapping arbitration logic to allow for multiple on-chip
devices to control a single SPMI master.
@@ -19,6 +19,10 @@ Required properties:
"core" - core registers
"intr" - interrupt controller registers
"cnfg" - configuration registers
+ Registers used only for V2 PMIC Arbiter:
+ "chnls" - tx-channel per virtual slave registers.
+ "obsrvr" - rx-channel (called observer) per virtual slave registers.
+
- reg : address + size pairs describing the PMIC arb register sets; order must
correspond with the order of entries in reg-names
- #address-cells : must be set to 2
--
cgit
From c0e6841653e9e96fea9e0f973a785bc66f45b532 Mon Sep 17 00:00:00 2001
From: Alex Smith <alex.smith@imgtec.com>
Date: Mon, 9 Mar 2015 14:29:03 +0000
Subject: dt-bindings: memory-controllers: Add binding for jz4780-nemc
Add device tree bindings for the NAND/External Memory Controller (NEMC)
on Ingenic JZ4780
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
.../memory-controllers/ingenic,jz4780-nemc.txt | 75 ++++++++++++++++++++++
1 file changed, 75 insertions(+)
create mode 100644 Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt
(limited to 'Documentation/devicetree')
diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt
new file mode 100644
index 000000000000..f936b5589b19
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt
@@ -0,0 +1,75 @@
+* Ingenic JZ4780 NAND/external memory controller (NEMC)
+
+This file documents the device tree bindings for the NEMC external memory
+controller in Ingenic JZ4780
+
+Required properties:
+- compatible: Should be set to one of:
+ "ingenic,jz4780-nemc" (JZ4780)
+- reg: Should specify the NEMC controller registers location and length.
+- clocks: Clock for the NEMC controller.
+- #address-cells: Must be set to 2.
+- #size-cells: Must be set to 1.
+- ranges: A set of ranges for each bank describing the physical memory layout.
+ Each should specify the following 4 integer values:
+
+ <cs number> 0 <physical address of mapping> <size of mapping>
+
+Each child of the NEMC node describes a device connected to the NEMC.
+
+Required child node properties:
+- reg: Should contain at least one register specifier, given in the following
+ format:
+
+ <cs number> <offset> <size>
+
+ Multiple registers can be specified across multiple banks. This is needed,
+ for example, for packaged NAND devices with multiple dies. Such devices
+ should be grouped into a single node.
+
+Optional child node properties:
+- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits.
+- ingenic,nemc-tAS: Address setup time in nanoseconds.
+- ingenic,nemc-tAH: Address hold time in nanoseconds.
+- ingenic,nemc-tBP: Burst pitch time in nanoseconds.
+- ingenic,nemc-tAW: Access wait time in nanoseconds.
+- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds.
+
+If a child node references multiple banks in its "reg" property, the same value
+for all optional parameters will be configured for all banks. If any optional
+parameters are omitted, they will be left unchanged from whatever they are
+configured to when the NEMC device is probed (which may be the reset value as
+given in the hardware reference manual, or a value configured by the boot
+loader).
+
+Example (NEMC node with a NAND child device attached at CS1):
+
+nemc: nemc@13410000 {
+ compatible = "ingenic,jz4780-nemc";
+ reg = <0x13410000 0x10000>;
+
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ ranges = <1 0 0x1b000000 0x1000000
+ 2 0 0x1a000000 0x1000000
+ 3 0 0x19000000 0x1000000
+ 4 0 0x18000000 0x1000000
+ 5 0 0x17000000 0x1000000
+ 6 0 0x16000000 0x1000000>;
+
+ clocks = <&cgu JZ4780_CLK_NEMC>;
+
+ nand: nand@1 {
+ compatible = "ingenic,jz4780-nand";
+ reg = <1 0 0x1000000>;
+
+ ingenic,nemc-tAS = <10>;
+ ingenic,nemc-tAH = <5>;
+ ingenic,nemc-tBP = <10>;
+ ingenic,nemc-tAW = <15>;
+ ingenic,nemc-tSTRV = <100>;
+
+ ...
+ };
+};
--
cgit
From 223437c72ae008094e43199dea93c3a144c4e153 Mon Sep 17 00:00:00 2001
From: Kaixu Xia <xiakaixu@huawei.com>
Date: Mon, 30 Mar 2015 14:13:39 -0600
Subject: coresight: remove the unnecessary configuration
coresight-default-sink
The coresight-default-sink configuration option has been
removed from the framework. As such remove it from DT and bindings.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
Documentation/devicetree/bindings/arm/coresight.txt | 1 -
1 file changed, 1 deletion(-)
(limited to 'Documentation/devicetree')
diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt
index a3089359aaa6..88602b75418e 100644
--- a/Documentation/devicetree/bindings/arm/coresight.txt
+++ b/Documentation/devicetree/bindings/arm/coresight.txt
@@ -61,7 +61,6 @@ Example:
compatible = "arm,coresight-etb10", "arm,primecell";
reg = <0 0x20010000 0 0x1000>;
- coresight-default-sink;
clocks = <&oscclk6a>;
clock-names = "apb_pclk";
port {
--
cgit
From 21e8681862a544517c1c9d6515770efe3897e326 Mon Sep 17 00:00:00 2001
From: Sebastian Reichel <sre@kernel.org>
Date: Fri, 27 Mar 2015 15:39:45 +0100
Subject: Documentation: DT: lis302: update wakeup binding
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
This updated the documentation of the DT binding to
describe the added wakeup threshold and second wakeup
engine.
It also adds a note, that the axis values may be
negative.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
Documentation/devicetree/bindings/misc/lis302.txt | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
(limited to 'Documentation/devicetree')
diff --git a/Documentation/devicetree/bindings/misc/lis302.txt b/Documentation/devicetree/bindings/misc/lis302.txt
index 6def86f6b053..2a19bff9693f 100644
--- a/Documentation/devicetree/bindings/misc/lis302.txt
+++ b/Documentation/devicetree/bindings/misc/lis302.txt
@@ -46,11 +46,18 @@ Optional properties for all bus drivers:
interrupt 2
- st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
upper/lower limit
+ - st,wakeup-threshold: set wakeup threshold
+ - st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
+ upper/lower limit for second wakeup
+ engine.
+ - st,wakeup2-threshold: set wakeup threshold for second wakeup
+ engine.
- st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
highpass cut-off frequency
- st,hipass{1,2}-disable: disable highpass 1/2.
- st,default-rate=: set the default rate
- - st,axis-{x,y,z}=: set the axis to map to the three coordinates
+ - st,axis-{x,y,z}=: set the axis to map to the three coordinates.
+ Negative values can be used for inverted axis.
- st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis
(used by self-test)
--
cgit