From fb50a116bbbc25c7c11e00e6d10a53b9ec3c38e8 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Fri, 28 Feb 2014 16:57:34 +0100 Subject: drm/tegra: hdmi - Add connector supply support Revert commit 18ebc0f404d5 "drm/tegra: hdmi: Enable VDD earlier for hotplug/DDC" and instead add a new supply for the +5V pin on the HDMI connector. The vdd-supply property refers to the regulator that supplies the AVDD_HDMI input on Tegra, rather than the +5V HDMI connector pin. This was never a problem before, because all boards had that pin hooked up to a regulator that was always on. Starting with Dalmore and continuing with Venice2, the +5V pin is controllable via a GPIO. For reasons unknown, the GPIO ended up as the controlling GPIO of the AVDD_HDMI supply in the Dalmore and Venice2 DTS files. But that's not correct. Instead, a separate supply must be introduced so that the +5V pin can be controlled separately from the supplies that feed the HDMI block within Tegra. A new hdmi-supply property is introduced that takes the place of the vdd-supply and vdd-supply is only enabled when HDMI is enabled rather than all the time. Signed-off-by: Thierry Reding --- Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt index efa8b8451f93..f13a6b8263d3 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -136,6 +136,7 @@ of the following host1x client modules: - compatible: "nvidia,tegra-hdmi" - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. + - hdmi-supply: supply for the +5V HDMI connector pin - vdd-supply: regulator for supply voltage - pll-supply: regulator for PLL - clocks: Must contain an entry for each entry in clock-names. -- cgit From 3b077afb3a7d84bffbf6598697a17655933671d2 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Fri, 14 Mar 2014 14:07:50 +0100 Subject: drm/tegra: dsi - Implement VDD supply support The DSI controllers are powered by a (typically 1.2V) regulator. Usually this is always on, so there was no need to support enabling or disabling it thus far. But in order not to consume any power when DSI is inactive, give the driver a chance to enable or disable the supply as needed. Signed-off-by: Thierry Reding --- Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt index f13a6b8263d3..b48f4ef31d93 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -181,6 +181,7 @@ of the following host1x client modules: See ../reset/reset.txt for details. - reset-names: Must include the following entries: - dsi + - avdd-dsi-supply: phandle of a supply that powers the DSI controller - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying which pads are used by this DSI output and need to be calibrated. See also ../mipi/nvidia,tegra114-mipi.txt. -- cgit