From 0978e95253c64bda17e1c2da5c30744980ca73d3 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 16 Sep 2019 14:50:17 +0200 Subject: dt-bindings: pci: amlogic, meson-pcie: Add G12A bindings Add PCIE bindings for the Amlogic G12A SoC, the support is the same but the PHY is shared with USB3 to control the differential lines. Thus this adds a phy phandle to control the PHY, and only requires the MIPI clock for the Amlogic AXG SoC Family. Signed-off-by: Neil Armstrong Signed-off-by: Lorenzo Pieralisi Reviewed-by: Rob Herring Reviewed-by: Andrew Murray --- Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt index efa2c8b9b85a..84fdc422792e 100644 --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt @@ -9,13 +9,16 @@ Additional properties are described here: Required properties: - compatible: - should contain "amlogic,axg-pcie" to identify the core. + should contain : + - "amlogic,axg-pcie" for AXG SoC Family + - "amlogic,g12a-pcie" for G12A SoC Family + to identify the core. - reg: should contain the configuration address space. - reg-names: Must be - "elbi" External local bus interface registers - "cfg" Meson specific registers - - "phy" Meson PCIE PHY registers + - "phy" Meson PCIE PHY registers for AXG SoC Family - "config" PCIe configuration space - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. - clocks: Must contain an entry for each entry in clock-names. @@ -23,12 +26,13 @@ Required properties: - "pclk" PCIe GEN 100M PLL clock - "port" PCIe_x(A or B) RC clock gate - "general" PCIe Phy clock - - "mipi" PCIe_x(A or B) 100M ref clock gate + - "mipi" PCIe_x(A or B) 100M ref clock gate for AXG SoC Family - resets: phandle to the reset lines. - reset-names: must contain "phy" "port" and "apb" - - "phy" Share PHY reset + - "phy" Share PHY reset for AXG SoC Family - "port" Port A or B reset - "apb" Share APB reset +- phys: should contain a phandle to the shared phy for G12A SoC Family - device_type: should be "pci". As specified in designware-pcie.txt -- cgit From d8725e38dd9fe88bc7dab6e53acdf2e257c241db Mon Sep 17 00:00:00 2001 From: Xiaowei Bao Date: Mon, 2 Sep 2019 11:43:17 +0800 Subject: dt-bindings: pci: layerscape-pci: add compatible strings "fsl, ls1028a-pcie" Add the PCIe compatible string for LS1028A. Signed-off-by: Xiaowei Bao Signed-off-by: Hou Zhiqiang Signed-off-by: Lorenzo Pieralisi Reviewed-by: Rob Herring Reviewed-by: Andrew Murray --- Documentation/devicetree/bindings/pci/layerscape-pci.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index e20ceaab9b38..99a386ea691c 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -21,6 +21,7 @@ Required properties: "fsl,ls1046a-pcie" "fsl,ls1043a-pcie" "fsl,ls1012a-pcie" + "fsl,ls1028a-pcie" EP mode: "fsl,ls1046a-pcie-ep", "fsl,ls-pcie-ep" - reg: base addresses and lengths of the PCIe controller register blocks. -- cgit