From e68015d1973134442170cb562baf8eeb4bb02602 Mon Sep 17 00:00:00 2001 From: "H. Nikolaus Schaller" Date: Tue, 19 Jul 2016 13:47:31 +0200 Subject: DT: leds: Add bindings for ISSI is31fl319x This adds a binding description for ISSI is31fl319x LED controllers. Signed-off-by: H. Nikolaus Schaller Acked-by: Rob Herring Signed-off-by: Jacek Anaszewski --- .../devicetree/bindings/leds/leds-is31fl319x.txt | 59 ++++++++++++++++++++++ 1 file changed, 59 insertions(+) create mode 100644 Documentation/devicetree/bindings/leds/leds-is31fl319x.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt new file mode 100644 index 000000000000..fc2603484544 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-is31fl319x.txt @@ -0,0 +1,59 @@ +LEDs connected to is31fl319x LED controller chip + +Required properties: +- compatible : Should be any of + "issi,is31fl3190" + "issi,is31fl3191" + "issi,is31fl3193" + "issi,is31fl3196" + "issi,is31fl3199" + "si-en,sn3199". +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- reg: 0x64, 0x65, 0x66, or 0x67. + +Optional properties: +- audio-gain-db : audio gain selection for external analog modulation input. + Valid values: 0 - 21, step by 3 (rounded down) + Default: 0 + +Each led is represented as a sub-node of the issi,is31fl319x device. +There can be less leds subnodes than the chip can support but not more. + +Required led sub-node properties: +- reg : number of LED line + Valid values: 1 - number of leds supported by the chip variant. + +Optional led sub-node properties: +- label : see Documentation/devicetree/bindings/leds/common.txt. +- linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt. +- led-max-microamp : (optional) + Valid values: 5000 - 40000, step by 5000 (rounded down) + Default: 20000 (20 mA) + Note: a driver will take the lowest of all led limits since the + chip has a single global setting. The lowest value will be chosen + due to the PWM specificity, where lower brightness is achieved + by reducing the dury-cycle of pulses and not the current, which + will always have its peak value equal to led-max-microamp. + +Examples: + +fancy_leds: leds@65 { + compatible = "issi,is31fl3196"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x65>; + + red_aux: led@1 { + label = "red:aux"; + reg = <1>; + led-max-microamp = <10000>; + }; + + green_power: led@5 { + label = "green:power"; + reg = <5>; + linux,default-trigger = "default-on"; + }; +}; -- cgit From 9a6b1f608acd0948acbfc7ddafaf27bc00293302 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 16 Aug 2016 11:25:02 +0200 Subject: leds: pm8058: add device tree bindings This adds the device tree bindings for the PM8058 LEDs. Cc: devicetree@vger.kernel.org Cc: linux-arm-msm@vger.kernel.org Cc: Andy Gross Cc: Stephen Boyd Signed-off-by: Linus Walleij Acked-by: Bjorn Andersson Acked-by: Rob Herring Signed-off-by: Jacek Anaszewski --- .../devicetree/bindings/leds/leds-pm8058.txt | 67 ++++++++++++++++++++++ 1 file changed, 67 insertions(+) create mode 100644 Documentation/devicetree/bindings/leds/leds-pm8058.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/leds/leds-pm8058.txt b/Documentation/devicetree/bindings/leds/leds-pm8058.txt new file mode 100644 index 000000000000..89584c49aab2 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pm8058.txt @@ -0,0 +1,67 @@ +Qualcomm PM8058 LED driver + +The Qualcomm PM8058 is a multi-functional device which contains +an LED driver block for up to six LEDs: three normal LEDs, two +"flash" LEDs and one "keypad backlight" LED. The names are +quoted because sometimes these LED drivers are used for wildly +different things than flash or keypad backlight: their names +are more of a suggestion than a hard-wired usecase. + +Hardware-wise the different LEDs support slightly different +output currents. The "flash" LEDs do not need to charge nor +do they support external triggers. They are just powerful LED +drivers. + +The LEDs appear as children to the PM8058 device, with the +proper compatible string. For the PM8058 bindings see: +mfd/qcom-pm8xxx.txt. + +Each LED is represented as a sub-node of the syscon device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: + +Required properties: +- compatible: one of + "qcom,pm8058-led" (for the normal LEDs at 0x131, 0x132 and 0x133) + "qcom,pm8058-keypad-led" (for the "keypad" LED at 0x48) + "qcom,pm8058-flash-led" (for the "flash" LEDs at 0x49 and 0xFB) + +Optional properties: +- label: see Documentation/devicetree/bindings/leds/common.txt +- default-state: see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: + +qcom,ssbi@500000 { + pmicintc: pmic@0 { + compatible = "qcom,pm8058"; + led@48 { + compatible = "qcom,pm8058-keypad-led"; + reg = <0x48>; + label = "pm8050:white:keypad"; + default-state = "off"; + }; + led@131 { + compatible = "qcom,pm8058-led"; + reg = <0x131>; + label = "pm8058:red"; + default-state = "off"; + }; + led@132 { + compatible = "qcom,pm8058-led"; + reg = <0x132>; + label = "pm8058:yellow"; + default-state = "off"; + linux,default-trigger = "mmc0"; + }; + led@133 { + compatible = "qcom,pm8058-led"; + reg = <0x133>; + label = "pm8058:green"; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; +}; -- cgit From 1d1a77ddc8acfa3d506f1958e09a12085e71fc69 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 16 Aug 2016 21:41:36 +0200 Subject: leds: centralize definition of "default-state" property Four different drivers define the "default-state" property. Move this into the common.txt common LEDs properties. Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij Acked-by: Rob Herring Signed-off-by: Jacek Anaszewski --- Documentation/devicetree/bindings/leds/common.txt | 7 +++++++ Documentation/devicetree/bindings/leds/leds-bcm6328.txt | 2 +- Documentation/devicetree/bindings/leds/leds-bcm6358.txt | 2 +- Documentation/devicetree/bindings/leds/leds-gpio.txt | 9 ++------- Documentation/devicetree/bindings/leds/register-bit-led.txt | 9 ++------- 5 files changed, 13 insertions(+), 16 deletions(-) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 93ef6e6e43b5..696be5792625 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -19,6 +19,13 @@ Optional properties for child nodes: a device, i.e. no other LED class device can be assigned the same label. +- default-state : The initial state of the LED. Valid values are "on", "off", + and "keep". If the LED is already on or off and the default-state property is + set the to same value, then no glitch should be produced where the LED + momentarily turns off (or on). The "keep" setting will keep the LED at + whatever its current state is, without producing a glitch. The default is + off if this property is not present. + - linux,default-trigger : This parameter, if present, is a string defining the trigger assigned to the LED. Current triggers are: "backlight" - LED will act as a back-light, controlled by the framebuffer diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt index 3f48c1eaf085..ccebce597f37 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -49,7 +49,7 @@ LED sub-node optional properties: - active-low : Boolean, makes LED active low. Default : false - default-state : see - Documentation/devicetree/bindings/leds/leds-gpio.txt + Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt index b22a55bcc65d..da5708e7b43b 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6358.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6358.txt @@ -28,7 +28,7 @@ LED sub-node optional properties: - active-low : Boolean, makes LED active low. Default : false - default-state : see - Documentation/devicetree/bindings/leds/leds-gpio.txt + Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index 5b1b43a64265..76535ca37120 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -14,13 +14,8 @@ LED sub-node properties: see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt -- default-state: (optional) The initial state of the LED. Valid - values are "on", "off", and "keep". If the LED is already on or off - and the default-state property is set the to same value, then no - glitch should be produced where the LED momentarily turns off (or - on). The "keep" setting will keep the LED at whatever its current - state is, without producing a glitch. The default is off if this - property is not present. +- default-state: (optional) The initial state of the LED. + see Documentation/devicetree/bindings/leds/common.txt - retain-state-suspended: (optional) The suspend state can be retained.Such as charge-led gpio. - panic-indicator : (optional) diff --git a/Documentation/devicetree/bindings/leds/register-bit-led.txt b/Documentation/devicetree/bindings/leds/register-bit-led.txt index 379cefdc0bda..59b56365f648 100644 --- a/Documentation/devicetree/bindings/leds/register-bit-led.txt +++ b/Documentation/devicetree/bindings/leds/register-bit-led.txt @@ -23,13 +23,8 @@ Optional properties: see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : (optional) see Documentation/devicetree/bindings/leds/common.txt -- default-state: (optional) The initial state of the LED. Valid - values are "on", "off", and "keep". If the LED is already on or off - and the default-state property is set the to same value, then no - glitch should be produced where the LED momentarily turns off (or - on). The "keep" setting will keep the LED at whatever its current - state is, without producing a glitch. The default is off if this - property is not present. +- default-state: (optional) The initial state of the LED + see Documentation/devicetree/bindings/leds/common.txt Example: -- cgit From 1f70cb4045cba47287fed3ba98dadc7187f13ef8 Mon Sep 17 00:00:00 2001 From: Rafał Miłecki Date: Fri, 26 Aug 2016 16:19:36 +0200 Subject: Documentation: move oneshot trigger attributes documentation to ABI MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Documentation of sysfs interface should be in ABI in the first place. This moves relevant part of documentation and mentions where to look for it. Fix trivial typos whilst we are at it. Signed-off-by: Rafał Miłecki Signed-off-by: Jacek Anaszewski --- Documentation/ABI/testing/sysfs-class-led | 3 +- .../ABI/testing/sysfs-class-led-trigger-oneshot | 36 ++++++++++++++++++++++ Documentation/leds/ledtrig-oneshot.txt | 20 ++---------- 3 files changed, 40 insertions(+), 19 deletions(-) create mode 100644 Documentation/ABI/testing/sysfs-class-led-trigger-oneshot (limited to 'Documentation') diff --git a/Documentation/ABI/testing/sysfs-class-led b/Documentation/ABI/testing/sysfs-class-led index 3646ec85d513..86ace287d48b 100644 --- a/Documentation/ABI/testing/sysfs-class-led +++ b/Documentation/ABI/testing/sysfs-class-led @@ -24,7 +24,8 @@ Description: of led events. You can change triggers in a similar manner to the way an IO scheduler is chosen. Trigger specific parameters can appear in - /sys/class/leds/ once a given trigger is selected. + /sys/class/leds/ once a given trigger is selected. For + their documentation see sysfs-class-led-trigger-*. What: /sys/class/leds//inverted Date: January 2011 diff --git a/Documentation/ABI/testing/sysfs-class-led-trigger-oneshot b/Documentation/ABI/testing/sysfs-class-led-trigger-oneshot new file mode 100644 index 000000000000..378a3a4df3c8 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-led-trigger-oneshot @@ -0,0 +1,36 @@ +What: /sys/class/leds//delay_on +Date: Jun 2012 +KernelVersion: 3.6 +Contact: linux-leds@vger.kernel.org +Description: + Specifies for how many milliseconds the LED has to stay at + LED_FULL brightness after it has been armed. + Defaults to 100 ms. + +What: /sys/class/leds//delay_off +Date: Jun 2012 +KernelVersion: 3.6 +Contact: linux-leds@vger.kernel.org +Description: + Specifies for how many milliseconds the LED has to stay at + LED_OFF brightness after it has been armed. + Defaults to 100 ms. + +What: /sys/class/leds//invert +Date: Jun 2012 +KernelVersion: 3.6 +Contact: linux-leds@vger.kernel.org +Description: + Reverse the blink logic. If set to 0 (default) blink on for + delay_on ms, then blink off for delay_off ms, leaving the LED + normally off. If set to 1, blink off for delay_off ms, then + blink on for delay_on ms, leaving the LED normally on. + Setting this value also immediately changes the LED state. + +What: /sys/class/leds//shot +Date: Jun 2012 +KernelVersion: 3.6 +Contact: linux-leds@vger.kernel.org +Description: + Write any non-empty string to signal an events, this starts a + blink sequence if not already running. diff --git a/Documentation/leds/ledtrig-oneshot.txt b/Documentation/leds/ledtrig-oneshot.txt index 07cd1fa41a3a..fe57474a12e2 100644 --- a/Documentation/leds/ledtrig-oneshot.txt +++ b/Documentation/leds/ledtrig-oneshot.txt @@ -21,24 +21,8 @@ below: echo oneshot > trigger -This adds the following sysfs attributes to the LED: - - delay_on - specifies for how many milliseconds the LED has to stay at - LED_FULL brightness after it has been armed. - Default to 100 ms. - - delay_off - specifies for how many milliseconds the LED has to stay at - LED_OFF brightness after it has been armed. - Default to 100 ms. - - invert - reverse the blink logic. If set to 0 (default) blink on for delay_on - ms, then blink off for delay_off ms, leaving the LED normally off. If - set to 1, blink off for delay_off ms, then blink on for delay_on ms, - leaving the LED normally on. - Setting this value also immediately change the LED state. - - shot - write any non-empty string to signal an events, this starts a blink - sequence if not already running. +This adds sysfs attributes to the LED that are documented in: +Documentation/ABI/testing/sysfs-class-led-trigger-oneshot Example use-case: network devices, initialization: -- cgit From be4fdf99fa4dc95aa01144b207caf2cc9fa074d8 Mon Sep 17 00:00:00 2001 From: Vadim Pasternak Date: Thu, 8 Sep 2016 07:25:53 +0000 Subject: leds: add driver for Mellanox systems LEDs This makes it possible to create a set of LEDs for Mellanox systems: "msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740", "msn2100". Driver obtains LED devices according to system configuration, provided through system DMI data, like mlxcpld:fan1:green, mlxcpld:fan1:red and creates devices in form: "devicename:colour:function". LED setting is controlled through on board CPLD Lattice device. For setting particular LED off, solid, blink: echo 0 > /sys/class/leds/mlxcpld\:status\:green/brightness echo 1 > /sys/class/leds/mlxcpld\:status\:green/brightness echo timer > /sys/class/leds/mlxcpld\:status\:green/trigger On module probing all LEDs are set green, on removing - off. Last setting overwrites previous, f.e. sequence for changing LED from green - red - green: echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness echo 1 > /sys/class/leds/mlxcpld\:psu\:red/brightness echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness Note: LEDs cannot be turned on/off simultaneously. The Kconfig currently controlling compilation of this code is: drivers/leds/Kconfig:config LEDS_MLXCPLD Signed-off-by: Vadim Pasternak Reviewed-by: Jiri Pirko Reviewed-by: Wei Yongjun Signed-off-by: Jacek Anaszewski --- Documentation/leds/leds-mlxcpld.txt | 110 ++++++++++++++++++++++++++++++++++++ 1 file changed, 110 insertions(+) create mode 100644 Documentation/leds/leds-mlxcpld.txt (limited to 'Documentation') diff --git a/Documentation/leds/leds-mlxcpld.txt b/Documentation/leds/leds-mlxcpld.txt new file mode 100644 index 000000000000..a0e8fd457117 --- /dev/null +++ b/Documentation/leds/leds-mlxcpld.txt @@ -0,0 +1,110 @@ +Kernel driver for Mellanox systems LEDs +======================================= + +Provide system LED support for the nex Mellanox systems: +"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", +"msn2410", "msb7800", "msn2740", "msn2100". + +Description +----------- +Driver provides the following LEDs for the systems "msx6710", "msx6720", +"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740": + mlxcpld:fan1:green + mlxcpld:fan1:red + mlxcpld:fan2:green + mlxcpld:fan2:red + mlxcpld:fan3:green + mlxcpld:fan3:red + mlxcpld:fan4:green + mlxcpld:fan4:red + mlxcpld:psu:green + mlxcpld:psu:red + mlxcpld:status:green + mlxcpld:status:red + + "status" + CPLD reg offset: 0x20 + Bits [3:0] + + "psu" + CPLD reg offset: 0x20 + Bits [7:4] + + "fan1" + CPLD reg offset: 0x21 + Bits [3:0] + + "fan2" + CPLD reg offset: 0x21 + Bits [7:4] + + "fan3" + CPLD reg offset: 0x22 + Bits [3:0] + + "fan4" + CPLD reg offset: 0x22 + Bits [7:4] + + Color mask for all the above LEDs: + [bit3,bit2,bit1,bit0] or + [bit7,bit6,bit5,bit4]: + [0,0,0,0] = LED OFF + [0,1,0,1] = Red static ON + [1,1,0,1] = Green static ON + [0,1,1,0] = Red blink 3Hz + [1,1,1,0] = Green blink 3Hz + [0,1,1,1] = Red blink 6Hz + [1,1,1,1] = Green blink 6Hz + +Driver provides the following LEDs for the system "msn2100": + mlxcpld:fan:green + mlxcpld:fan:red + mlxcpld:psu1:green + mlxcpld:psu1:red + mlxcpld:psu2:green + mlxcpld:psu2:red + mlxcpld:status:green + mlxcpld:status:red + mlxcpld:uid:blue + + "status" + CPLD reg offset: 0x20 + Bits [3:0] + + "fan" + CPLD reg offset: 0x21 + Bits [3:0] + + "psu1" + CPLD reg offset: 0x23 + Bits [3:0] + + "psu2" + CPLD reg offset: 0x23 + Bits [7:4] + + "uid" + CPLD reg offset: 0x24 + Bits [3:0] + + Color mask for all the above LEDs, excepted uid: + [bit3,bit2,bit1,bit0] or + [bit7,bit6,bit5,bit4]: + [0,0,0,0] = LED OFF + [0,1,0,1] = Red static ON + [1,1,0,1] = Green static ON + [0,1,1,0] = Red blink 3Hz + [1,1,1,0] = Green blink 3Hz + [0,1,1,1] = Red blink 6Hz + [1,1,1,1] = Green blink 6Hz + + Color mask for uid LED: + [bit3,bit2,bit1,bit0]: + [0,0,0,0] = LED OFF + [1,1,0,1] = Blue static ON + [1,1,1,0] = Blue blink 3Hz + [1,1,1,1] = Blue blink 6Hz + +Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle). +For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec. -- cgit