From 851320e3f33503f557135a7fef6da66a2f7eec55 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 13 Sep 2013 12:09:53 -0700 Subject: ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c) removed legacy booting in favor of device tree based booting for pandaboard. That caused the WLAN to stop working as the related .dts entries fell through the cracks. The legacy muxing was setting pulls for GPIO 48 and 49, so let's keep that behaviour for now to avoid further regressions for BT and FM. Also input logic was enabled for MMC CLK line, but I've verified that the input logic we don't need enabled for CLK line as it's not bidirectional. Also, we want to use non-removable instead of ti,non-removable as the ti,non-removable also sets no_regulator_off_init which is really not what we want as then wl12xx won't get powered up and down which is needed for resetting it. Note that looks like the WLAN interface fails to come up after a warm reset, but that most likely was also happening with the legacy booting and needs a separate fix. Cc: Paolo Pisati Cc: Rajendra Nayak Cc: Luciano Coelho Signed-off-by: Tony Lindgren Signed-off-by: Benoit Cousson --- arch/arm/boot/dts/omap4-panda-common.dtsi | 46 ++++++++++++++++++++++++++++++- 1 file changed, 45 insertions(+), 1 deletion(-) (limited to 'arch/arm/boot/dts/omap4-panda-common.dtsi') diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index faa95b5b242e..814ab67c8c29 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -107,6 +107,19 @@ */ clock-frequency = <19200000>; }; + + /* regulator for wl12xx on sdio5 */ + wl12xx_vmmc: wl12xx_vmmc { + pinctrl-names = "default"; + pinctrl-0 = <&wl12xx_gpio>; + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio2 11 0>; + startup-delay-us = <70000>; + enable-active-high; + }; }; &omap4_pmx_wkup { @@ -235,6 +248,33 @@ 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ >; }; + + /* + * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP + * REVISIT: Are the pull-ups needed for GPIO 48 and 49? + */ + wl12xx_gpio: pinmux_wl12xx_gpio { + pinctrl-single,pins = < + 0x26 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */ + 0x2c (PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */ + 0x30 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */ + 0x32 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */ + >; + }; + + /* wl12xx GPIO inputs and SDIO pins */ + wl12xx_pins: pinmux_wl12xx_pins { + pinctrl-single,pins = < + 0x38 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */ + 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ + 0x108 (PIN_OUTPUT | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ + 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ + 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ + 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ + >; + }; }; &i2c1 { @@ -314,8 +354,12 @@ }; &mmc5 { - ti,non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&wl12xx_pins>; + vmmc-supply = <&wl12xx_vmmc>; + non-removable; bus-width = <4>; + cap-power-off-card; }; &emif1 { -- cgit