From 3696d303d6a39f916f9ace37d79e3db7937c68a7 Mon Sep 17 00:00:00 2001 From: Bryan Buckley Date: Fri, 30 Sep 2011 11:05:55 -0700 Subject: ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1 Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance with the control module programming guide. This fixes a bug where if trying to use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be affected by a changing SDMMC1_VDDS. Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever SDMMC1_VDDS ramps up/down or changes for cell protection purposes. MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore they can operate independently. Signed-off-by: Bryan Buckley Acked-by: Kishore Kadiyala Tested-by: Balaji T K Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/hsmmc.c | 12 ++++-------- 1 file changed, 4 insertions(+), 8 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c index a9b45c76e1d3..097a42d81e59 100644 --- a/arch/arm/mach-omap2/hsmmc.c +++ b/arch/arm/mach-omap2/hsmmc.c @@ -137,8 +137,7 @@ static void omap4_hsmmc1_before_set_reg(struct device *dev, int slot, */ reg = omap4_ctrl_pad_readl(control_pbias_offset); reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } @@ -156,8 +155,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, else reg |= OMAP4_MMC1_PBIASLITE_VMODE_MASK; reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); timeout = jiffies + msecs_to_jiffies(5); @@ -171,16 +169,14 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) { pr_err("Pbias Voltage is not same as LDO\n"); /* Caution : On VMODE_ERROR Power Down MMC IO */ - reg &= ~(OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + reg &= ~(OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } } else { reg = omap4_ctrl_pad_readl(control_pbias_offset); reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_MMC1_PBIASLITE_VMODE_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PBIASLITE_VMODE_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } } -- cgit From bfd46a543f8f90bb197225900e355ce3c7daeb1f Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 30 Sep 2011 11:05:55 -0700 Subject: ARM: OMAP: Fix i2c init for twl4030 Looks like 2600 kHz rate does not work reliably on 2430, so just use the 100 kHz rate. Otherwise the system often fails to boot properly with: omap_i2c omap_i2c.2: timeout waiting for bus ready omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages twl: clock init err [-110] omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages TWL4030 Unable to unlock IDCODE registers --110 Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-2430sdp.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index 2028464cf5b9..f79b7d2a8ed4 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -193,7 +193,8 @@ static int __init omap2430_i2c_init(void) { omap_register_i2c_bus(1, 100, sdp2430_i2c1_boardinfo, ARRAY_SIZE(sdp2430_i2c1_boardinfo)); - omap2_pmic_init("twl4030", &sdp2430_twldata); + omap_pmic_init(2, 100, "twl4030", INT_24XX_SYS_NIRQ, + &sdp2430_twldata); return 0; } -- cgit From b8e111a74d281b70e88bd67fec48cfda4f9bdce2 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Fri, 30 Sep 2011 11:05:55 -0700 Subject: ARM: OMAP: musb: Remove a redundant omap4430_phy_init call in usb_musb_init Current code calls omap4430_phy_init() twice in usb_musb_init(). Calling omap4430_phy_init() once is enough. This patch removes the first omap4430_phy_init() call, which using an uninitialized pointer as parameter. This patch elimates below build warning: arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init': arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function Signed-off-by: Axel Lin Bjarne Steinsbo Acked-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/usb-musb.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index a65145b02a55..19e4dac62a8c 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -137,9 +137,6 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data) musb_plat.mode = board_data->mode; musb_plat.extvbus = board_data->extvbus; - if (cpu_is_omap44xx()) - omap4430_phy_init(dev); - if (cpu_is_omap3517() || cpu_is_omap3505()) { oh_name = "am35x_otg_hs"; name = "musb-am35x"; -- cgit From 002ea9eefec98dada56fd5f8e432a4e8570c2a26 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 29 Sep 2011 09:37:23 +0100 Subject: ARM: 7113/1: mm: Align bank start to MAX_ORDER_NR_PAGES The VM subsystem assumes that there are valid memmap entries from the bank start aligned to MAX_ORDER_NR_PAGES. On the Ux500 we have a lot of mem=N arguments on the commandline triggering this bug several times over and causing kernel oops messages. Cc: stable@kernel.org Cc: Michael Bohan Cc: Nicolas Pitre Signed-off-by: Johan Palsson Signed-off-by: Rabin Vincent Signed-off-by: Linus Walleij Signed-off-by: Russell King --- arch/arm/mm/init.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index cc7e2d8be9aa..f8037ba338ac 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -496,6 +496,13 @@ static void __init free_unused_memmap(struct meminfo *mi) */ bank_start = min(bank_start, ALIGN(prev_bank_end, PAGES_PER_SECTION)); +#else + /* + * Align down here since the VM subsystem insists that the + * memmap entries are valid from the bank start aligned to + * MAX_ORDER_NR_PAGES. + */ + bank_start = round_down(bank_start, MAX_ORDER_NR_PAGES); #endif /* * If we had a previous bank, and there is a space -- cgit From 98e87d57aab9b1594f9cc53a386fcb6f2f2ba6e2 Mon Sep 17 00:00:00 2001 From: srinidhi kasagar Date: Tue, 20 Sep 2011 11:15:46 +0530 Subject: ARM: mach-ux500: enable fix for ARM errata 754322 This applies ARM errata fix 754322 for all ux500 platforms. Cc: stable@kernel.org Signed-off-by: srinidhi kasagar Signed-off-by: Linus Walleij --- arch/arm/mach-ux500/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig index 4210cb434dbc..a3e0c8692f0d 100644 --- a/arch/arm/mach-ux500/Kconfig +++ b/arch/arm/mach-ux500/Kconfig @@ -6,6 +6,7 @@ config UX500_SOC_COMMON select ARM_GIC select HAS_MTU select ARM_ERRATA_753970 + select ARM_ERRATA_754322 menu "Ux500 SoC" -- cgit From 3faf12cd8603e3efbcc7e570e07dfd1ea2a17095 Mon Sep 17 00:00:00 2001 From: Marc Dietrich Date: Fri, 7 Oct 2011 08:31:41 -0700 Subject: ARM: tegra: fix compilation error due to mach/hardware.h removal This fixes a compilation error in cpu-tegra.c which was introduced in dc8d966bccde ("ARM: convert PCI defines to variables") which removed the now obsolete mach/hardware.h from the mach-tegra subtree. Signed-off-by: Marc Dietrich Signed-off-by: Olof Johansson Cc: Sergei Shtylyov Signed-off-by: Linus Torvalds --- arch/arm/mach-tegra/cpu-tegra.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-tegra/cpu-tegra.c b/arch/arm/mach-tegra/cpu-tegra.c index 0e1016a827ac..0e0fd4d889bd 100644 --- a/arch/arm/mach-tegra/cpu-tegra.c +++ b/arch/arm/mach-tegra/cpu-tegra.c @@ -32,7 +32,6 @@ #include -#include #include /* Frequency table index must be sequential starting at 0 */ -- cgit From 29a541f6c1f6e4a85628bb86071b9e72c9f8be2c Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Mon, 3 Oct 2011 18:30:53 +0100 Subject: ARM: 7117/1: perf: fix HW_CACHE_* events on Cortex-A9 Using COHERENT_LINE_{MISS,HIT} for cache misses and references respectively is completely wrong. Instead, use the L1D events which are a better and more useful approximation despite ignoring instruction traffic. Reported-by: Alasdair Grant Reported-by: Matt Horsnell Reported-by: Michael Williams Cc: stable@kernel.org Cc: Jean Pihet Signed-off-by: Will Deacon Signed-off-by: Russell King --- arch/arm/kernel/perf_event_v7.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/perf_event_v7.c b/arch/arm/kernel/perf_event_v7.c index 4c851834f68e..6be3e2e4d838 100644 --- a/arch/arm/kernel/perf_event_v7.c +++ b/arch/arm/kernel/perf_event_v7.c @@ -321,8 +321,8 @@ static const unsigned armv7_a9_perf_map[PERF_COUNT_HW_MAX] = { [PERF_COUNT_HW_CPU_CYCLES] = ARMV7_PERFCTR_CPU_CYCLES, [PERF_COUNT_HW_INSTRUCTIONS] = ARMV7_PERFCTR_INST_OUT_OF_RENAME_STAGE, - [PERF_COUNT_HW_CACHE_REFERENCES] = ARMV7_PERFCTR_COHERENT_LINE_HIT, - [PERF_COUNT_HW_CACHE_MISSES] = ARMV7_PERFCTR_COHERENT_LINE_MISS, + [PERF_COUNT_HW_CACHE_REFERENCES] = ARMV7_PERFCTR_DCACHE_ACCESS, + [PERF_COUNT_HW_CACHE_MISSES] = ARMV7_PERFCTR_DCACHE_REFILL, [PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = ARMV7_PERFCTR_PC_WRITE, [PERF_COUNT_HW_BRANCH_MISSES] = ARMV7_PERFCTR_PC_BRANCH_MIS_PRED, [PERF_COUNT_HW_BUS_CYCLES] = ARMV7_PERFCTR_CLOCK_CYCLES, -- cgit From bb1ac3ec95cf0cce5145617b140f2090ed45d565 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Thu, 6 Oct 2011 14:57:24 +0100 Subject: ARM: 7122/1: localtimer: add header linux/errno.h explicitly MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Per the text in Documentation/SubmitChecklist as below, we should explicitly have header linux/errno.h in localtimer.h for ENXIO reference. 1: If you use a facility then #include the file that defines/declares that facility. Don't depend on other header files pulling in ones that you use. Otherwise, we may run into some compiling error like the following one, if any file includes localtimer.h without CONFIG_LOCAL_TIMERS defined. arch/arm/include/asm/localtimer.h: In function ‘local_timer_setup’: arch/arm/include/asm/localtimer.h:53:10: error: ‘ENXIO’ undeclared (first use in this function) Signed-off-by: Shawn Guo Signed-off-by: Russell King --- arch/arm/include/asm/localtimer.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/localtimer.h b/arch/arm/include/asm/localtimer.h index 080d74f8128d..ff66638ff54d 100644 --- a/arch/arm/include/asm/localtimer.h +++ b/arch/arm/include/asm/localtimer.h @@ -10,6 +10,8 @@ #ifndef __ASM_ARM_LOCALTIMER_H #define __ASM_ARM_LOCALTIMER_H +#include + struct clock_event_device; /* -- cgit From f8be12d15374413cf437741a282e97129e759209 Mon Sep 17 00:00:00 2001 From: Zoltan Devai Date: Mon, 10 Oct 2011 14:54:12 +0100 Subject: ARM: 7128/1: vic: Don't write to the read-only register VIC_IRQ_STATUS This is unneeded and causes an abort on the SPMP8000 platform. Acked-by: Linus Walleij Signed-off-by: Zoltan Devai Signed-off-by: Russell King --- arch/arm/common/vic.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/common/vic.c b/arch/arm/common/vic.c index 7aa4262ada7a..197f81c77351 100644 --- a/arch/arm/common/vic.c +++ b/arch/arm/common/vic.c @@ -259,7 +259,6 @@ static void __init vic_disable(void __iomem *base) writel(0, base + VIC_INT_SELECT); writel(0, base + VIC_INT_ENABLE); writel(~0, base + VIC_INT_ENABLE_CLEAR); - writel(0, base + VIC_IRQ_STATUS); writel(0, base + VIC_ITCR); writel(~0, base + VIC_INT_SOFT_CLEAR); } -- cgit