From d0cf9d8a3c78cf70e3a78e898fdc1b2adea0e6dd Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Tue, 28 Jun 2016 12:18:51 -0700 Subject: ARM: brcmstb: Add earlyprintk support using run-time checks The SUN_TOP_CTRL_FAMILY_ID register is at a fixed absolute address for all of our supported chips, so utilize its value to determine what the UARTA base address should be based on the value we read. Since the code is called both during decompressor when the MMU is off, and after the MMU has been turned on in the kernel, and we want to do the lookup only once, we use the same technique as tegra.S and have a shared storage location between the decompressor and the kernel. Signed-off-by: Florian Fainelli --- arch/arm/Kconfig.debug | 14 ++-- arch/arm/include/debug/brcmstb.S | 145 +++++++++++++++++++++++++++++++++++++++ arch/arm/mach-bcm/brcmstb.c | 16 +++++ 3 files changed, 168 insertions(+), 7 deletions(-) create mode 100644 arch/arm/include/debug/brcmstb.S (limited to 'arch/arm') diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index a9693b6987a6..a660508a58bd 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -186,10 +186,11 @@ choice config DEBUG_BRCMSTB_UART bool "Use BRCMSTB UART for low-level debug" depends on ARCH_BRCMSTB - select DEBUG_UART_8250 help Say Y here if you want the debug print routines to direct - their output to the first serial port on these devices. + their output to the first serial port on these devices. The + UART physical and virtual address is automatically provided + based on the chip identification register value. If you have a Broadcom STB chip and would like early print messages to appear over the UART, select this option. @@ -1430,6 +1431,7 @@ config DEBUG_LL_INCLUDE default "debug/zynq.S" if DEBUG_ZYNQ_UART0 || DEBUG_ZYNQ_UART1 default "debug/bcm63xx.S" if DEBUG_BCM63XX_UART default "debug/digicolor.S" if DEBUG_DIGICOLOR_UA0 + default "debug/brcmstb.S" if DEBUG_BRCMSTB_UART default "mach/debug-macro.S" # Compatibility options for PL01x @@ -1520,7 +1522,6 @@ config DEBUG_UART_PHYS default 0xe6e60000 if DEBUG_RCAR_GEN2_SCIF0 default 0xe8008000 if DEBUG_R7S72100_SCIF2 default 0xf0000be0 if ARCH_EBSA110 - default 0xf040ab00 if DEBUG_BRCMSTB_UART default 0xf1012000 if DEBUG_MVEBU_UART0_ALTERNATE default 0xf1012100 if DEBUG_MVEBU_UART1_ALTERNATE default 0xf7fc9000 if DEBUG_BERLIN_UART @@ -1604,7 +1605,6 @@ config DEBUG_UART_VIRT default 0xfb009000 if DEBUG_REALVIEW_STD_PORT default 0xfb00c000 if DEBUG_AT91_SAMA5D4_USART3 default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT - default 0xfc40ab00 if DEBUG_BRCMSTB_UART default 0xfc705000 if DEBUG_ZTE_ZX default 0xfcfe8600 if DEBUG_BCM63XX_UART default 0xfd000000 if DEBUG_SPEAR3XX || DEBUG_SPEAR13XX @@ -1677,8 +1677,7 @@ config DEBUG_UART_8250_WORD DEBUG_ALPINE_UART0 || \ DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \ DEBUG_DAVINCI_DA8XX_UART2 || \ - DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2 || \ - DEBUG_BRCMSTB_UART + DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2 config DEBUG_UART_8250_PALMCHIP bool "8250 UART is Palmchip BK-310x" @@ -1697,7 +1696,8 @@ config DEBUG_UNCOMPRESS bool depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG || ARM_SINGLE_ARMV7M default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \ - (!DEBUG_TEGRA_UART || !ZBOOT_ROM) + (!DEBUG_TEGRA_UART || !ZBOOT_ROM) && \ + !DEBUG_BRCMSTB_UART help This option influences the normal decompressor output for multiplatform kernels. Normally, multiplatform kernels disable diff --git a/arch/arm/include/debug/brcmstb.S b/arch/arm/include/debug/brcmstb.S new file mode 100644 index 000000000000..9113d7b33ae0 --- /dev/null +++ b/arch/arm/include/debug/brcmstb.S @@ -0,0 +1,145 @@ +/* + * Copyright (C) 2016 Broadcom + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include + +/* Physical register offset and virtual register offset */ +#define REG_PHYS_BASE 0xf0000000 +#define REG_VIRT_BASE 0xfc000000 +#define REG_PHYS_ADDR(x) ((x) + REG_PHYS_BASE) + +/* Product id can be read from here */ +#define SUN_TOP_CTRL_BASE REG_PHYS_ADDR(0x404000) + +#define UARTA_3390 REG_PHYS_ADDR(0x40a900) +#define UARTA_7250 REG_PHYS_ADDR(0x40b400) +#define UARTA_7268 REG_PHYS_ADDR(0x40c000) +#define UARTA_7271 UARTA_7268 +#define UARTA_7364 REG_PHYS_ADDR(0x40b000) +#define UARTA_7366 UARTA_7364 +#define UARTA_74371 REG_PHYS_ADDR(0x406b00) +#define UARTA_7439 REG_PHYS_ADDR(0x40a900) +#define UARTA_7445 REG_PHYS_ADDR(0x40ab00) + +#define UART_SHIFT 2 + +#define checkuart(rp, rv, family_id, family) \ + /* Load family id */ \ + ldr rp, =family_id ; \ + /* Compare SUN_TOP_CTRL value against it */ \ + cmp rp, rv ; \ + /* Passed test, load address */ \ + ldreq rp, =UARTA_##family ; \ + /* Jump to save UART address */ \ + beq 91f + + .macro addruart, rp, rv, tmp + adr \rp, 99f @ actual addr of 99f + ldr \rv, [\rp] @ linked addr is stored there + sub \rv, \rv, \rp @ offset between the two + ldr \rp, [\rp, #4] @ linked brcmstb_uart_config + sub \tmp, \rp, \rv @ actual brcmstb_uart_config + ldr \rp, [\tmp] @ Load brcmstb_uart_config + cmp \rp, #1 @ needs initialization? + bne 100f @ no; go load the addresses + mov \rv, #0 @ yes; record init is done + str \rv, [\tmp] + + /* Check SUN_TOP_CTRL base */ + ldr \rp, =SUN_TOP_CTRL_BASE @ load SUN_TOP_CTRL PA + ldr \rv, [\rp, #0] @ get register contents + and \rv, \rv, #0xffffff00 @ strip revision bits [7:0] + + /* Chip specific detection starts here */ +20: checkuart(\rp, \rv, 0x33900000, 3390) +21: checkuart(\rp, \rv, 0x72500000, 7250) +22: checkuart(\rp, \rv, 0x72680000, 7268) +23: checkuart(\rp, \rv, 0x72710000, 7271) +24: checkuart(\rp, \rv, 0x73640000, 7364) +25: checkuart(\rp, \rv, 0x73660000, 7366) +26: checkuart(\rp, \rv, 0x07437100, 74371) +27: checkuart(\rp, \rv, 0x74390000, 7439) +28: checkuart(\rp, \rv, 0x74450000, 7445) + + /* No valid UART found */ +90: mov \rp, #0 + /* fall through */ + + /* Record whichever UART we chose */ +91: str \rp, [\tmp, #4] @ Store in brcmstb_uart_phys + cmp \rp, #0 @ Valid UART address? + bne 92f @ Yes, go process it + str \rp, [\tmp, #8] @ Store 0 in brcmstb_uart_virt + b 100f @ Done +92: and \rv, \rp, #0xffffff @ offset within 16MB section + add \rv, \rv, #REG_VIRT_BASE + str \rv, [\tmp, #8] @ Store in brcmstb_uart_virt + b 100f + + .align +99: .word . + .word brcmstb_uart_config + .ltorg + + /* Load previously selected UART address */ +100: ldr \rp, [\tmp, #4] @ Load brcmstb_uart_phys + ldr \rv, [\tmp, #8] @ Load brcmstb_uart_virt + .endm + + .macro store, rd, rx:vararg + str \rd, \rx + .endm + + .macro load, rd, rx:vararg + ldr \rd, \rx + .endm + + .macro senduart,rd,rx + store \rd, [\rx, #UART_TX << UART_SHIFT] + .endm + + .macro busyuart,rd,rx +1002: load \rd, [\rx, #UART_LSR << UART_SHIFT] + and \rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE + teq \rd, #UART_LSR_TEMT | UART_LSR_THRE + bne 1002b + .endm + + .macro waituart,rd,rx + .endm + +/* + * Storage for the state maintained by the macros above. + * + * In the kernel proper, this data is located in arch/arm/mach-bcm/brcmstb.c. + * That's because this header is included from multiple files, and we only + * want a single copy of the data. In particular, the UART probing code above + * assumes it's running using physical addresses. This is true when this file + * is included from head.o, but not when included from debug.o. So we need + * to share the probe results between the two copies, rather than having + * to re-run the probing again later. + * + * In the decompressor, we put the symbol/storage right here, since common.c + * isn't included in the decompressor build. This symbol gets put in .text + * even though it's really data, since .data is discarded from the + * decompressor. Luckily, .text is writeable in the decompressor, unless + * CONFIG_ZBOOT_ROM. That dependency is handled in arch/arm/Kconfig.debug. + */ +#if defined(ZIMAGE) +brcmstb_uart_config: + /* Debug UART initialization required */ + .word 1 + /* Debug UART physical address */ + .word 0 + /* Debug UART virtual address */ + .word 0 +#endif diff --git a/arch/arm/mach-bcm/brcmstb.c b/arch/arm/mach-bcm/brcmstb.c index 99a67cfb7c0d..07e3a86c6466 100644 --- a/arch/arm/mach-bcm/brcmstb.c +++ b/arch/arm/mach-bcm/brcmstb.c @@ -19,6 +19,22 @@ #include #include +/* + * Storage for debug-macro.S's state. + * + * This must be in .data not .bss so that it gets initialized each time the + * kernel is loaded. The data is declared here rather than debug-macro.S so + * that multiple inclusions of debug-macro.S point at the same data. + */ +u32 brcmstb_uart_config[3] = { + /* Debug UART initialization required */ + 1, + /* Debug UART physical address */ + 0, + /* Debug UART virtual address */ + 0, +}; + static void __init brcmstb_init_irq(void) { irqchip_init(); -- cgit