From fd385b33762620a48d098e0490b98782fe9d07a6 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 3 Feb 2014 14:46:19 +0100 Subject: ARM: ux500: move AB8500 YCBCR settings to device tree This moves the pin control settings for the YCBCR connector on the AB8500 over to the device tree as a hog. Cc: Patrice Chotard Cc: Lee Jones Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-href-ab8500.dtsi | 23 ++++++++++++++++++++++- arch/arm/mach-ux500/board-mop500-pins.c | 10 ---------- 2 files changed, 22 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/ste-href-ab8500.dtsi b/arch/arm/boot/dts/ste-href-ab8500.dtsi index 58b00d0f023e..2b548e90878e 100644 --- a/arch/arm/boot/dts/ste-href-ab8500.dtsi +++ b/arch/arm/boot/dts/ste-href-ab8500.dtsi @@ -31,7 +31,8 @@ <&gpio39_default_mode>, <&gpio42_default_mode>, <&gpio26_default_mode>, - <&gpio35_default_mode>; + <&gpio35_default_mode>, + <&ycbcr_default_mode>; /* * Pins 2, 4, 10, 11, 12, 13, 16, 24, 25, 36, 37, 38, 39 and 42 @@ -246,6 +247,26 @@ }; }; }; + /* + * This sets up the YCBCR connector pins, i.e. analog video out. + * Set as input with no bias. + */ + ycbcr { + ycbcr_default_mode: ycbcr_default { + default_mux { + ste,function = "ycbcr"; + ste,pins = "ycbcr0123_d_1"; + }; + default_cfg { + ste,pins = "GPIO6_Y18", + "GPIO7_AA20", + "GPIO8_W18", + "GPIO9_AA19"; + input-enable; + bias-disable; + }; + }; + }; }; }; }; diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c index 139298043685..d58513b08a6d 100644 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ b/arch/arm/mach-ux500/board-mop500-pins.c @@ -56,16 +56,6 @@ static struct pinctrl_map __initdata ab8500_pinmap[] = { AB8500_MUX_STATE("gpio3_a_1", "gpio", "regulator.36", PINCTRL_STATE_SLEEP), AB8500_PIN_STATE("GPIO3_U9", in_pd, "regulator.36", PINCTRL_STATE_SLEEP), - /* - * pins 6,7,8 and 9 are muxed in YCBCR0123 - * configured in INPUT PULL UP - */ - AB8500_MUX_HOG("ycbcr0123_d_1", "ycbcr"), - AB8500_PIN_HOG("GPIO6_Y18", in_nopull), - AB8500_PIN_HOG("GPIO7_AA20", in_nopull), - AB8500_PIN_HOG("GPIO8_W18", in_nopull), - AB8500_PIN_HOG("GPIO9_AA19", in_nopull), - /* * pins 14,15 are muxed in PWM1 and PWM2 * configured in INPUT PULL DOWN -- cgit