From 9b26d5c044d6a29ebfb1845408e0f2a7c5f89818 Mon Sep 17 00:00:00 2001 From: Dario Binacchi Date: Mon, 8 Jan 2024 21:15:52 +0100 Subject: drm/panel: nt35510: move hardwired parameters to configuration This patch, preparatory for future developments, move the hardwired parameters to configuration data to allow the addition of new NT35510-based panels. Signed-off-by: Dario Binacchi Reviewed-by: Linus Walleij Tested-by: Linus Walleij Signed-off-by: Linus Walleij Link: https://patchwork.freedesktop.org/patch/msgid/20240108201618.2798649-8-dario.binacchi@amarulasolutions.com --- drivers/gpu/drm/panel/panel-novatek-nt35510.c | 140 +++++++++++++++++++++----- 1 file changed, 115 insertions(+), 25 deletions(-) (limited to 'drivers/gpu/drm/panel') diff --git a/drivers/gpu/drm/panel/panel-novatek-nt35510.c b/drivers/gpu/drm/panel/panel-novatek-nt35510.c index 83a9cf53d269..3ecaf87939e6 100644 --- a/drivers/gpu/drm/panel/panel-novatek-nt35510.c +++ b/drivers/gpu/drm/panel/panel-novatek-nt35510.c @@ -171,6 +171,10 @@ struct nt35510_config { * timing in the display controller. */ const struct drm_display_mode mode; + /** + * @mode_flags: DSI operation mode related flags + */ + unsigned long mode_flags; /** * @avdd: setting for AVDD ranging from 0x00 = 6.5V to 0x14 = 4.5V * in 0.1V steps the default is 0x05 which means 6.0V @@ -273,6 +277,100 @@ struct nt35510_config { * same layout of bytes as @vgp. */ u8 vgn[NT35510_P1_VGN_LEN]; + /** + * @dopctr: setting optional control for display + * ERR bits 0..1 in the first byte is the ERR pin output signal setting. + * 0 = Disable, ERR pin output low + * 1 = ERR pin output CRC error only + * 2 = ERR pin output ECC error only + * 3 = ERR pin output CRC and ECC error + * The default is 0. + * N565 bit 2 in the first byte is the 16-bit/pixel format selection. + * 0 = R[4:0] + G[5:3] & G[2:0] + B[4:0] + * 1 = G[2:0] + R[4:0] & B[4:0] + G[5:3] + * The default is 0. + * DIS_EoTP_HS bit 3 in the first byte is "DSI protocol violation" error + * reporting. + * 0 = reporting when error + * 1 = not reporting when error + * DSIM bit 4 in the first byte is the video mode data type enable + * 0 = Video mode data type disable + * 1 = Video mode data type enable + * The default is 0. + * DSIG bit 5 int the first byte is the generic r/w data type enable + * 0 = Generic r/w disable + * 1 = Generic r/w enable + * The default is 0. + * DSITE bit 6 in the first byte is TE line enable + * 0 = TE line is disabled + * 1 = TE line is enabled + * The default is 0. + * RAMKP bit 7 in the first byte is the frame memory keep/loss in + * sleep-in mode + * 0 = contents loss in sleep-in + * 1 = contents keep in sleep-in + * The default is 0. + * CRL bit 1 in the second byte is the source driver data shift + * direction selection. This bit is XOR operation with bit RSMX + * of 3600h command. + * 0 (RMSX = 0) = S1 -> S1440 + * 0 (RMSX = 1) = S1440 -> S1 + * 1 (RMSX = 0) = S1440 -> S1 + * 1 (RMSX = 1) = S1 -> S1440 + * The default is 0. + * CTB bit 2 in the second byte is the vertical scanning direction + * selection for gate control signals. This bit is XOR operation + * with bit ML of 3600h command. + * 0 (ML = 0) = Forward (top -> bottom) + * 0 (ML = 1) = Reverse (bottom -> top) + * 1 (ML = 0) = Reverse (bottom -> top) + * 1 (ML = 1) = Forward (top -> bottom) + * The default is 0. + * CRGB bit 3 in the second byte is RGB-BGR order selection. This + * bit is XOR operation with bit RGB of 3600h command. + * 0 (RGB = 0) = RGB/Normal + * 0 (RGB = 1) = BGR/RB swap + * 1 (RGB = 0) = BGR/RB swap + * 1 (RGB = 1) = RGB/Normal + * The default is 0. + * TE_PWR_SEL bit 4 in the second byte is the TE output voltage + * level selection (only valid when DSTB_SEL = 0 or DSTB_SEL = 1, + * VSEL = High and VDDI = 1.665~3.3V). + * 0 = TE output voltage level is VDDI + * 1 = TE output voltage level is VDDA + * The default is 0. + */ + u8 dopctr[NT35510_P0_DOPCTR_LEN]; + /** + * @madctl: Memory data access control + * RSMY bit 0 is flip vertical. Flips the display image top to down. + * RSMX bit 1 is flip horizontal. Flips the display image left to right. + * MH bit 2 is the horizontal refresh order. + * RGB bit 3 is the RGB-BGR order. + * 0 = RGB color sequence + * 1 = BGR color sequence + * ML bit 4 is the vertical refresh order. + * MV bit 5 is the row/column exchange. + * MX bit 6 is the column address order. + * MY bit 7 is the row address order. + */ + u8 madctl; + /** + * @sdhdtctr: source output data hold time + * 0x00..0x3F = 0..31.5us in steps of 0.5us + * The default is 0x05 = 2.5us. + */ + u8 sdhdtctr; + /** + * @gseqctr: EQ control for gate signals + * GFEQ_XX[3:0]: time setting of EQ step for falling edge in steps + * of 0.5us. + * The default is 0x07 = 3.5us + * GREQ_XX[7:4]: time setting of EQ step for rising edge in steps + * of 0.5us. + * The default is 0x07 = 3.5us + */ + u8 gseqctr[NT35510_P0_GSEQCTR_LEN]; /** * @sdeqctr: Source driver control settings, first byte is * 0 for mode 1 and 1 for mode 2. Mode 1 uses two steps and @@ -536,46 +634,28 @@ static int nt35510_setup_display(struct nt35510 *nt) { struct mipi_dsi_device *dsi = to_mipi_dsi_device(nt->dev); const struct nt35510_config *conf = nt->conf; - u8 dopctr[NT35510_P0_DOPCTR_LEN]; - u8 gseqctr[NT35510_P0_GSEQCTR_LEN]; u8 dpfrctr[NT35510_P0_DPFRCTR1_LEN]; - /* FIXME: set up any rotation (assume none for now) */ - u8 addr_mode = NT35510_ROTATE_0_SETTING; - u8 val; int ret; - /* Enable TE, EoTP and RGB pixel format */ - dopctr[0] = NT35510_DOPCTR_0_DSITE | NT35510_DOPCTR_0_EOTP | - NT35510_DOPCTR_0_N565; - dopctr[1] = NT35510_DOPCTR_1_CTB; ret = nt35510_send_long(nt, dsi, NT35510_P0_DOPCTR, NT35510_P0_DOPCTR_LEN, - dopctr); + conf->dopctr); if (ret) return ret; - ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_ADDRESS_MODE, &addr_mode, - sizeof(addr_mode)); + ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_ADDRESS_MODE, &conf->madctl, + sizeof(conf->madctl)); if (ret < 0) return ret; - /* - * Source data hold time, default 0x05 = 2.5us - * 0x00..0x3F = 0 .. 31.5us in steps of 0.5us - * 0x0A = 5us - */ - val = 0x0A; - ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDHDTCTR, &val, - sizeof(val)); + ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDHDTCTR, &conf->sdhdtctr, + sizeof(conf->sdhdtctr)); if (ret < 0) return ret; - /* EQ control for gate signals, 0x00 = 0 us */ - gseqctr[0] = 0x00; - gseqctr[1] = 0x00; ret = nt35510_send_long(nt, dsi, NT35510_P0_GSEQCTR, NT35510_P0_GSEQCTR_LEN, - gseqctr); + conf->gseqctr); if (ret) return ret; @@ -896,7 +976,6 @@ static int nt35510_probe(struct mipi_dsi_device *dsi) */ dsi->hs_rate = 349440000; dsi->lp_rate = 9600000; - dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS; /* * Every new incarnation of this display must have a unique @@ -908,6 +987,8 @@ static int nt35510_probe(struct mipi_dsi_device *dsi) return -ENODEV; } + dsi->mode_flags = nt->conf->mode_flags; + nt->supplies[0].supply = "vdd"; /* 2.3-4.8 V */ nt->supplies[1].supply = "vddi"; /* 1.65-3.3V */ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(nt->supplies), @@ -1030,6 +1111,7 @@ static const struct nt35510_config nt35510_hydis_hva40wv1 = { .vtotal = 800 + 2 + 0 + 5, /* VBP = 5 */ .flags = 0, }, + .mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS, /* 0x09: AVDD = 5.6V */ .avdd = { 0x09, 0x09, 0x09 }, /* 0x34: PCK = Hsync/2, BTP = 2 x VDDB */ @@ -1050,6 +1132,14 @@ static const struct nt35510_config nt35510_hydis_hva40wv1 = { .vgp = { 0x00, 0xA3, 0x00 }, /* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */ .vgn = { 0x00, 0xA3, 0x00 }, + /* Enable TE, EoTP and RGB pixel format */ + .dopctr = { NT35510_DOPCTR_0_DSITE | NT35510_DOPCTR_0_EOTP | + NT35510_DOPCTR_0_N565, NT35510_DOPCTR_1_CTB }, + .madctl = NT35510_ROTATE_0_SETTING, + /* 0x0A: SDT = 5 us */ + .sdhdtctr = 0x0A, + /* EQ control for gate signals, 0x00 = 0 us */ + .gseqctr = { 0x00, 0x00 }, /* SDEQCTR: source driver EQ mode 2, 2.5 us rise time on each step */ .sdeqctr = { 0x01, 0x05, 0x05, 0x05 }, /* SDVPCTR: Normal operation off color during v porch */ -- cgit