From 511d05e0dadd91d398ed14f043fbcc93d728b98c Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Thu, 20 Dec 2018 15:10:47 +0100 Subject: mtd: rawnand: sunxi: Handle the tREA > tRC / 2 case In non-EDO, tREA should be less than tRP to guarantee that the controller does not sample the IO lines too early. Unfortunately, the sunxi NAND controller does not allow us to have different values for tRP and tREH (tRP = tREH = tRW / 2). We have 2 options to overcome this limitation: 1/ Extend tRC to fulfil the tREA <= tRC / 2 constraint 2/ Use EDO mode (only works if timings->tRLOH > 0) Signed-off-by: Boris Brezillon Signed-off-by: Miquel Raynal --- drivers/mtd/nand/raw/sunxi_nand.c | 22 +++++++++++++++++++--- 1 file changed, 19 insertions(+), 3 deletions(-) (limited to 'drivers/mtd') diff --git a/drivers/mtd/nand/raw/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c index 4fd1f8da6906..4282bc477761 100644 --- a/drivers/mtd/nand/raw/sunxi_nand.c +++ b/drivers/mtd/nand/raw/sunxi_nand.c @@ -1442,6 +1442,20 @@ static int sunxi_nfc_setup_data_interface(struct nand_chip *nand, int csline, if (timings->tRHW_min > (min_clk_period * 20)) min_clk_period = DIV_ROUND_UP(timings->tRHW_min, 20); + /* + * In non-EDO, tREA should be less than tRP to guarantee that the + * controller does not sample the IO lines too early. Unfortunately, + * the sunxi NAND controller does not allow us to have different + * values for tRP and tREH (tRP = tREH = tRW / 2). + * + * We have 2 options to overcome this limitation: + * + * 1/ Extend tRC to fulfil the tREA <= tRC / 2 constraint + * 2/ Use EDO mode (only works if timings->tRLOH > 0) + */ + if (timings->tREA_max > min_clk_period && !timings->tRLOH_min) + min_clk_period = timings->tREA_max; + tWB = sunxi_nand_lookup_timing(tWB_lut, timings->tWB_max, min_clk_period); if (tWB < 0) { @@ -1497,14 +1511,16 @@ static int sunxi_nfc_setup_data_interface(struct nand_chip *nand, int csline, return -EINVAL; } + sunxi_nand->timing_ctl = 0; + /* * ONFI specification 3.1, paragraph 4.15.2 dictates that EDO data * output cycle timings shall be used if the host drives tRC less than - * 30 ns. + * 30 ns. We should also use EDO mode if tREA is bigger than tRP. */ min_clk_period = NSEC_PER_SEC / real_clk_rate; - sunxi_nand->timing_ctl = ((min_clk_period * 2) < 30) ? - NFC_TIMING_CTL_EDO : 0; + if (min_clk_period * 2 < 30 || min_clk_period * 1000 < timings->tREA_max) + sunxi_nand->timing_ctl = NFC_TIMING_CTL_EDO; return 0; } -- cgit