From bf29c2ff82fd37f4a5e0c6983016c15430ac6e35 Mon Sep 17 00:00:00 2001 From: Rasmus Villemoes Date: Fri, 4 Oct 2019 15:32:02 +0200 Subject: pwm: mxs: Implement ->apply() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit In preparation for supporting setting the polarity, switch the driver to support the ->apply() method. Signed-off-by: Rasmus Villemoes Reviewed-by: Uwe Kleine-König Signed-off-by: Thierry Reding --- drivers/pwm/pwm-mxs.c | 70 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 70 insertions(+) (limited to 'drivers/pwm') diff --git a/drivers/pwm/pwm-mxs.c b/drivers/pwm/pwm-mxs.c index b14376b47ac8..10efd3de0bb3 100644 --- a/drivers/pwm/pwm-mxs.c +++ b/drivers/pwm/pwm-mxs.c @@ -26,6 +26,7 @@ #define PERIOD_PERIOD_MAX 0x10000 #define PERIOD_ACTIVE_HIGH (3 << 16) #define PERIOD_INACTIVE_LOW (2 << 18) +#define PERIOD_POLARITY_NORMAL (PERIOD_ACTIVE_HIGH | PERIOD_INACTIVE_LOW) #define PERIOD_CDIV(div) (((div) & 0x7) << 20) #define PERIOD_CDIV_MAX 8 @@ -41,6 +42,74 @@ struct mxs_pwm_chip { #define to_mxs_pwm_chip(_chip) container_of(_chip, struct mxs_pwm_chip, chip) +static int mxs_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, + const struct pwm_state *state) +{ + struct mxs_pwm_chip *mxs = to_mxs_pwm_chip(chip); + int ret, div = 0; + unsigned int period_cycles, duty_cycles; + unsigned long rate; + unsigned long long c; + + if (state->polarity != PWM_POLARITY_NORMAL) + return -ENOTSUPP; + + /* + * If the PWM channel is disabled, make sure to turn on the + * clock before calling clk_get_rate() and writing to the + * registers. Otherwise, just keep it enabled. + */ + if (!pwm_is_enabled(pwm)) { + ret = clk_prepare_enable(mxs->clk); + if (ret) + return ret; + } + + if (!state->enabled && pwm_is_enabled(pwm)) + writel(1 << pwm->hwpwm, mxs->base + PWM_CTRL + CLR); + + rate = clk_get_rate(mxs->clk); + while (1) { + c = rate / cdiv[div]; + c = c * state->period; + do_div(c, 1000000000); + if (c < PERIOD_PERIOD_MAX) + break; + div++; + if (div >= PERIOD_CDIV_MAX) + return -EINVAL; + } + + period_cycles = c; + c *= state->duty_cycle; + do_div(c, state->period); + duty_cycles = c; + + /* + * The data sheet the says registers must be written to in + * this order (ACTIVEn, then PERIODn). Also, the new settings + * only take effect at the beginning of a new period, avoiding + * glitches. + */ + writel(duty_cycles << 16, + mxs->base + PWM_ACTIVE0 + pwm->hwpwm * 0x20); + writel(PERIOD_PERIOD(period_cycles) | PERIOD_POLARITY_NORMAL | PERIOD_CDIV(div), + mxs->base + PWM_PERIOD0 + pwm->hwpwm * 0x20); + + if (state->enabled) { + if (!pwm_is_enabled(pwm)) { + /* + * The clock was enabled above. Just enable + * the channel in the control register. + */ + writel(1 << pwm->hwpwm, mxs->base + PWM_CTRL + SET); + } + } else { + clk_disable_unprepare(mxs->clk); + } + return 0; +} + static int mxs_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, int duty_ns, int period_ns) { @@ -116,6 +185,7 @@ static void mxs_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm) } static const struct pwm_ops mxs_pwm_ops = { + .apply = mxs_pwm_apply, .config = mxs_pwm_config, .enable = mxs_pwm_enable, .disable = mxs_pwm_disable, -- cgit