From 49a80424e3ec23ee2748f360348e167d5c748256 Mon Sep 17 00:00:00 2001 From: Lukas Wunner Date: Sun, 2 Jan 2022 18:49:44 +0100 Subject: serial: pl011: Drop redundant DTR/RTS preservation on close/open Commit d8d8ffa47783 ("amba-pl011: do not disable RTS during shutdown") amended the PL011 serial driver to leave DTR/RTS polarity untouched on tty close. That change made sense. But the commit also added code to save DTR/RTS state to an internal variable on tty close and restore it on tty open. That part of the commit makes less sense: The driver has no ->pm() callback, so the uart remains powered after tty close and automatically preserves register state, including DTR/RTS. Saving and restoring registers isn't the job of the ->startup() and ->shutdown() callbacks anyway. Rather, it should happen in ->pm(). Additionally, after pl011_startup() restores the state, the serial core overrides it in uart_port_dtr_rts() if a baud rate has been set: tty_port_open() uart_port_activate() uart_startup() uart_port_startup() pl011_startup() # restores DTR/RTS from uap->old_cr tty_port_block_til_ready() tty_port_raise_dtr_rts # if (C_BAUD(tty)) uart_dtr_rts() uart_port_dtr_rts() # raises DTR/RTS The serial core also overrides DTR/RTS on tty close in uart_shutdown() if C_HUPCL(tty) is set. So a user-defined DTR/RTS polarity won't survive a close/open cycle anyway, unless the user has set the baud rate to zero and disabled hupcl on the tty. Bottom line is, the code to save and restore DTR/RTS has no effect. Remove it. Cc: Linus Walleij Cc: Russell King Signed-off-by: Lukas Wunner Link: https://lore.kernel.org/r/e22089ab49e6e78822c50c8c4db46bf3ee885623.1641129328.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/amba-pl011.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) (limited to 'drivers/tty') diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 7ca4f0da8309..1f1df46242f9 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -230,7 +230,6 @@ struct uart_amba_port { unsigned int im; /* interrupt mask */ unsigned int old_status; unsigned int fifosize; /* vendor-specific */ - unsigned int old_cr; /* state during shutdown */ unsigned int fixed_baud; /* vendor-set fixed baud rate */ char type[12]; bool rs485_tx_started; @@ -1805,8 +1804,8 @@ static int pl011_startup(struct uart_port *port) spin_lock_irq(&uap->port.lock); - /* restore RTS and DTR */ - cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR); + cr = pl011_read(uap, REG_CR); + cr &= UART011_CR_RTS | UART011_CR_DTR; cr |= UART01x_CR_UARTEN | UART011_CR_RXE; if (port->rs485.flags & SER_RS485_ENABLED) { @@ -1883,7 +1882,6 @@ static void pl011_disable_uart(struct uart_amba_port *uap) uap->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS); spin_lock_irq(&uap->port.lock); cr = pl011_read(uap, REG_CR); - uap->old_cr = cr; cr &= UART011_CR_RTS | UART011_CR_DTR; cr |= UART01x_CR_UARTEN | UART011_CR_TXE; pl011_write(cr, uap, REG_CR); @@ -2699,7 +2697,6 @@ static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap, index = pl011_probe_dt_alias(index, dev); - uap->old_cr = 0; uap->port.dev = dev; uap->port.mapbase = mmiobase->start; uap->port.membase = base; -- cgit