From a8972d5a49b408248294b5ecbdd0a085e4726349 Mon Sep 17 00:00:00 2001 From: Hugo Villeneuve Date: Fri, 27 Sep 2024 09:53:05 -0400 Subject: drm: panel: jd9365da-h3: fix reset signal polarity In jadard_prepare() a reset pulse is generated with the following statements (delays ommited for clarity): gpiod_set_value(jadard->reset, 1); --> Deassert reset gpiod_set_value(jadard->reset, 0); --> Assert reset for 10ms gpiod_set_value(jadard->reset, 1); --> Deassert reset However, specifying second argument of "0" to gpiod_set_value() means to deassert the GPIO, and "1" means to assert it. If the reset signal is defined as GPIO_ACTIVE_LOW in the DTS, the above statements will incorrectly generate the reset pulse (inverted) and leave it asserted (LOW) at the end of jadard_prepare(). Fix reset behavior by inverting gpiod_set_value() second argument in jadard_prepare(). Also modify second argument to devm_gpiod_get() in jadard_dsi_probe() to assert the reset when probing. Do not modify it in jadard_unprepare() as it is already properly asserted with "1", which seems to be the intended behavior. Fixes: 6b818c533dd8 ("drm: panel: Add Jadard JD9365DA-H3 DSI panel") Cc: stable@vger.kernel.org Signed-off-by: Hugo Villeneuve Reviewed-by: Neil Armstrong Reviewed-by: Linus Walleij Link: https://lore.kernel.org/r/20240927135306.857617-1-hugo@hugovil.com Signed-off-by: Neil Armstrong Link: https://patchwork.freedesktop.org/patch/msgid/20240927135306.857617-1-hugo@hugovil.com --- drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c b/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c index 45d09e6fa667..7d68a8acfe2e 100644 --- a/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c +++ b/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c @@ -109,13 +109,13 @@ static int jadard_prepare(struct drm_panel *panel) if (jadard->desc->lp11_to_reset_delay_ms) msleep(jadard->desc->lp11_to_reset_delay_ms); - gpiod_set_value(jadard->reset, 1); + gpiod_set_value(jadard->reset, 0); msleep(5); - gpiod_set_value(jadard->reset, 0); + gpiod_set_value(jadard->reset, 1); msleep(10); - gpiod_set_value(jadard->reset, 1); + gpiod_set_value(jadard->reset, 0); msleep(130); ret = jadard->desc->init(jadard); @@ -1130,7 +1130,7 @@ static int jadard_dsi_probe(struct mipi_dsi_device *dsi) dsi->format = desc->format; dsi->lanes = desc->lanes; - jadard->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + jadard->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); if (IS_ERR(jadard->reset)) { DRM_DEV_ERROR(&dsi->dev, "failed to get our reset GPIO\n"); return PTR_ERR(jadard->reset); -- cgit From b3fefbb30a1691533cb905006b69b2a474660744 Mon Sep 17 00:00:00 2001 From: David Hildenbrand Date: Fri, 24 Jan 2025 19:15:23 +0100 Subject: nouveau/svm: fix missing folio unlock + put after make_device_exclusive_range() In case we have to retry the loop, we are missing to unlock+put the folio. In that case, we will keep failing make_device_exclusive_range() because we cannot grab the folio lock, and even return from the function with the folio locked and referenced, effectively never succeeding the make_device_exclusive_range(). While at it, convert the other unlock+put to use a folio as well. This was found by code inspection. Fixes: 8f187163eb89 ("nouveau/svm: implement atomic SVM access") Signed-off-by: David Hildenbrand Reviewed-by: Alistair Popple Tested-by: Alistair Popple Signed-off-by: Danilo Krummrich Link: https://patchwork.freedesktop.org/patch/msgid/20250124181524.3584236-2-david@redhat.com --- drivers/gpu/drm/nouveau/nouveau_svm.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/nouveau/nouveau_svm.c b/drivers/gpu/drm/nouveau/nouveau_svm.c index b4da82ddbb6b..8ea98f06d39a 100644 --- a/drivers/gpu/drm/nouveau/nouveau_svm.c +++ b/drivers/gpu/drm/nouveau/nouveau_svm.c @@ -590,6 +590,7 @@ static int nouveau_atomic_range_fault(struct nouveau_svmm *svmm, unsigned long timeout = jiffies + msecs_to_jiffies(HMM_RANGE_DEFAULT_TIMEOUT); struct mm_struct *mm = svmm->notifier.mm; + struct folio *folio; struct page *page; unsigned long start = args->p.addr; unsigned long notifier_seq; @@ -616,12 +617,16 @@ static int nouveau_atomic_range_fault(struct nouveau_svmm *svmm, ret = -EINVAL; goto out; } + folio = page_folio(page); mutex_lock(&svmm->mutex); if (!mmu_interval_read_retry(¬ifier->notifier, notifier_seq)) break; mutex_unlock(&svmm->mutex); + + folio_unlock(folio); + folio_put(folio); } /* Map the page on the GPU. */ @@ -637,8 +642,8 @@ static int nouveau_atomic_range_fault(struct nouveau_svmm *svmm, ret = nvif_object_ioctl(&svmm->vmm->vmm.object, args, size, NULL); mutex_unlock(&svmm->mutex); - unlock_page(page); - put_page(page); + folio_unlock(folio); + folio_put(folio); out: mmu_interval_notifier_remove(¬ifier->notifier); -- cgit From ef24989a62eefa6293a6c1c59dbb8b7e646e76dd Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Thu, 13 Feb 2025 17:44:43 +0100 Subject: drm/msm/a6xx: Only print the GMU firmware version once We only fetch it once from userland, so let's also only notify the user once and not on every runtime resume. As you can notice by the tags chain, more than one user found this annoying. Reported-by: Jens Glathe Suggested-by: Abel Vesa Suggested-by: Rob Clark Signed-off-by: Konrad Dybcio Reviewed-by: Neil Armstrong Patchwork: https://patchwork.freedesktop.org/patch/637062/ Signed-off-by: Rob Clark --- drivers/gpu/drm/msm/adreno/a6xx_gmu.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/adreno/a6xx_gmu.c b/drivers/gpu/drm/msm/adreno/a6xx_gmu.c index 65d38b25c070..699b0dd34b18 100644 --- a/drivers/gpu/drm/msm/adreno/a6xx_gmu.c +++ b/drivers/gpu/drm/msm/adreno/a6xx_gmu.c @@ -813,10 +813,10 @@ static int a6xx_gmu_fw_load(struct a6xx_gmu *gmu) } ver = gmu_read(gmu, REG_A6XX_GMU_CORE_FW_VERSION); - DRM_INFO("Loaded GMU firmware v%u.%u.%u\n", - FIELD_GET(A6XX_GMU_CORE_FW_VERSION_MAJOR__MASK, ver), - FIELD_GET(A6XX_GMU_CORE_FW_VERSION_MINOR__MASK, ver), - FIELD_GET(A6XX_GMU_CORE_FW_VERSION_STEP__MASK, ver)); + DRM_INFO_ONCE("Loaded GMU firmware v%u.%u.%u\n", + FIELD_GET(A6XX_GMU_CORE_FW_VERSION_MAJOR__MASK, ver), + FIELD_GET(A6XX_GMU_CORE_FW_VERSION_MINOR__MASK, ver), + FIELD_GET(A6XX_GMU_CORE_FW_VERSION_STEP__MASK, ver)); return 0; } -- cgit From 669c285620231786fffe9d87ab432e08a6ed922b Mon Sep 17 00:00:00 2001 From: Rob Clark Date: Mon, 13 Jan 2025 07:48:41 -0800 Subject: drm/msm: Avoid rounding up to one jiffy If userspace is trying to achieve a timeout of zero, let 'em have it. Only round up if the timeout is greater than zero. Fixes: 4969bccd5f4e ("drm/msm: Avoid rounding down to zero jiffies") Signed-off-by: Rob Clark Reviewed-by: Akhil P Oommen Patchwork: https://patchwork.freedesktop.org/patch/632264/ --- drivers/gpu/drm/msm/msm_drv.h | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/msm_drv.h b/drivers/gpu/drm/msm/msm_drv.h index fee31680a6d5..a65077855201 100644 --- a/drivers/gpu/drm/msm/msm_drv.h +++ b/drivers/gpu/drm/msm/msm_drv.h @@ -537,15 +537,12 @@ static inline int align_pitch(int width, int bpp) static inline unsigned long timeout_to_jiffies(const ktime_t *timeout) { ktime_t now = ktime_get(); - s64 remaining_jiffies; - if (ktime_compare(*timeout, now) < 0) { - remaining_jiffies = 0; - } else { - ktime_t rem = ktime_sub(*timeout, now); - remaining_jiffies = ktime_divns(rem, NSEC_PER_SEC / HZ); - } + if (ktime_compare(*timeout, now) <= 0) + return 0; + ktime_t rem = ktime_sub(*timeout, now); + s64 remaining_jiffies = ktime_divns(rem, NSEC_PER_SEC / HZ); return clamp(remaining_jiffies, 1LL, (s64)INT_MAX); } -- cgit From 2f69e54584475ac85ea0e3407c9198ac7c6ea8ad Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 14 Dec 2024 00:14:17 +0200 Subject: drm/msm/dpu: skip watchdog timer programming through TOP on >= SM8450 The SM8450 and later chips have DPU_MDP_PERIPH_0_REMOVED feature bit set, which means that those platforms have dropped some of the registers, including the WD TIMER-related ones. Stop providing the callback to program WD timer on those platforms. Fixes: 100d7ef6995d ("drm/msm/dpu: add support for SM8450") Signed-off-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/628874/ Link: https://lore.kernel.org/r/20241214-dpu-drop-features-v1-1-988f0662cb7e@linaro.org Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.c index ad19330de61a..562a3f4c5238 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.c @@ -272,7 +272,7 @@ static void _setup_mdp_ops(struct dpu_hw_mdp_ops *ops, if (cap & BIT(DPU_MDP_VSYNC_SEL)) ops->setup_vsync_source = dpu_hw_setup_vsync_sel; - else + else if (!(cap & BIT(DPU_MDP_PERIPH_0_REMOVED))) ops->setup_vsync_source = dpu_hw_setup_wd_timer; ops->get_safe_status = dpu_hw_get_safe_status; -- cgit From af0a4a2090cce732c70ad6c5f4145b43f39e3fe9 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 14 Dec 2024 00:14:18 +0200 Subject: drm/msm/dpu: enable DPU_WB_INPUT_CTRL for DPU 5.x Several DPU 5.x platforms are supposed to be using DPU_WB_INPUT_CTRL, to bind WB and PINGPONG blocks, but they do not. Change those platforms to use WB_SM8250_MASK, which includes that bit. Fixes: 1f5bcc4316b3 ("drm/msm/dpu: enable writeback on SC8108X") Fixes: ab2b03d73a66 ("drm/msm/dpu: enable writeback on SM6125") Fixes: 47cebb740a83 ("drm/msm/dpu: enable writeback on SM8150") Signed-off-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/628876/ Link: https://lore.kernel.org/r/20241214-dpu-drop-features-v1-2-988f0662cb7e@linaro.org Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_0_sm8150.h | 2 +- drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_1_sc8180x.h | 2 +- drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_4_sm6125.h | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_0_sm8150.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_0_sm8150.h index 421afacb7248..36cc9dbc00b5 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_0_sm8150.h +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_0_sm8150.h @@ -297,7 +297,7 @@ static const struct dpu_wb_cfg sm8150_wb[] = { { .name = "wb_2", .id = WB_2, .base = 0x65000, .len = 0x2c8, - .features = WB_SDM845_MASK, + .features = WB_SM8250_MASK, .format_list = wb2_formats_rgb, .num_formats = ARRAY_SIZE(wb2_formats_rgb), .clk_ctrl = DPU_CLK_CTRL_WB2, diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_1_sc8180x.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_1_sc8180x.h index 641023b102bf..e8eacdb47967 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_1_sc8180x.h +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_1_sc8180x.h @@ -304,7 +304,7 @@ static const struct dpu_wb_cfg sc8180x_wb[] = { { .name = "wb_2", .id = WB_2, .base = 0x65000, .len = 0x2c8, - .features = WB_SDM845_MASK, + .features = WB_SM8250_MASK, .format_list = wb2_formats_rgb, .num_formats = ARRAY_SIZE(wb2_formats_rgb), .clk_ctrl = DPU_CLK_CTRL_WB2, diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_4_sm6125.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_4_sm6125.h index d039b96beb97..76f60a2df7a8 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_4_sm6125.h +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_4_sm6125.h @@ -144,7 +144,7 @@ static const struct dpu_wb_cfg sm6125_wb[] = { { .name = "wb_2", .id = WB_2, .base = 0x65000, .len = 0x2c8, - .features = WB_SDM845_MASK, + .features = WB_SM8250_MASK, .format_list = wb2_formats_rgb, .num_formats = ARRAY_SIZE(wb2_formats_rgb), .clk_ctrl = DPU_CLK_CTRL_WB2, -- cgit From 24b50b7340ab7e7b004ee6db43d625caa68498b0 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Tue, 17 Dec 2024 14:35:40 +0200 Subject: drm/msm/dpu: correct LM pairing for SM6150 The SM6150 platform doesn't have 3DMux (MERGE_3D) block, so it can not split the screen between two LMs. Drop lm_pair fields as they don't make sense for this platform. Suggested-by: Abhinav Kumar Fixes: cb2f9144693b ("drm/msm/dpu: Add SM6150 support") Signed-off-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/629377/ Link: https://lore.kernel.org/r/20241217-dpu-fix-sm6150-v2-1-9acc8f5addf3@linaro.org Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_3_sm6150.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_3_sm6150.h b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_3_sm6150.h index 621a2140f675..d761ed705bac 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_3_sm6150.h +++ b/drivers/gpu/drm/msm/disp/dpu1/catalog/dpu_5_3_sm6150.h @@ -116,14 +116,12 @@ static const struct dpu_lm_cfg sm6150_lm[] = { .sblk = &sdm845_lm_sblk, .pingpong = PINGPONG_0, .dspp = DSPP_0, - .lm_pair = LM_1, }, { .name = "lm_1", .id = LM_1, .base = 0x45000, .len = 0x320, .features = MIXER_QCM2290_MASK, .sblk = &sdm845_lm_sblk, .pingpong = PINGPONG_1, - .lm_pair = LM_0, }, { .name = "lm_2", .id = LM_2, .base = 0x46000, .len = 0x320, -- cgit From df9cf852ca3099feb8fed781bdd5d3863af001c8 Mon Sep 17 00:00:00 2001 From: Abhinav Kumar Date: Thu, 6 Feb 2025 11:46:36 -0800 Subject: drm/msm/dp: account for widebus and yuv420 during mode validation Widebus allows the DP controller to operate in 2 pixel per clock mode. The mode validation logic validates the mode->clock against the max DP pixel clock. However the max DP pixel clock limit assumes widebus is already enabled. Adjust the mode validation logic to only compare the adjusted pixel clock which accounts for widebus against the max DP pixel clock. Also fix the mode validation logic for YUV420 modes as in that case as well, only half the pixel clock is needed. Cc: stable@vger.kernel.org Fixes: 757a2f36ab09 ("drm/msm/dp: enable widebus feature for display port") Fixes: 6db6e5606576 ("drm/msm/dp: change clock related programming for YUV420 over DP") Reviewed-by: Dmitry Baryshkov Tested-by: Dale Whinham Patchwork: https://patchwork.freedesktop.org/patch/635789/ Link: https://lore.kernel.org/r/20250206-dp-widebus-fix-v2-1-cb89a0313286@quicinc.com Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/dp/dp_display.c | 11 ++++++----- drivers/gpu/drm/msm/dp/dp_drm.c | 5 ++++- 2 files changed, 10 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c index d852e7a85334..a129e26c3ddb 100644 --- a/drivers/gpu/drm/msm/dp/dp_display.c +++ b/drivers/gpu/drm/msm/dp/dp_display.c @@ -930,16 +930,17 @@ enum drm_mode_status msm_dp_bridge_mode_valid(struct drm_bridge *bridge, return -EINVAL; } - if (mode->clock > DP_MAX_PIXEL_CLK_KHZ) - return MODE_CLOCK_HIGH; - msm_dp_display = container_of(dp, struct msm_dp_display_private, msm_dp_display); link_info = &msm_dp_display->panel->link_info; - if (drm_mode_is_420_only(&dp->connector->display_info, mode) && - msm_dp_display->panel->vsc_sdp_supported) + if ((drm_mode_is_420_only(&dp->connector->display_info, mode) && + msm_dp_display->panel->vsc_sdp_supported) || + msm_dp_wide_bus_available(dp)) mode_pclk_khz /= 2; + if (mode_pclk_khz > DP_MAX_PIXEL_CLK_KHZ) + return MODE_CLOCK_HIGH; + mode_bpp = dp->connector->display_info.bpc * num_components; if (!mode_bpp) mode_bpp = default_bpp; diff --git a/drivers/gpu/drm/msm/dp/dp_drm.c b/drivers/gpu/drm/msm/dp/dp_drm.c index d3e241ea6941..16b7913d1eef 100644 --- a/drivers/gpu/drm/msm/dp/dp_drm.c +++ b/drivers/gpu/drm/msm/dp/dp_drm.c @@ -257,7 +257,10 @@ static enum drm_mode_status msm_edp_bridge_mode_valid(struct drm_bridge *bridge, return -EINVAL; } - if (mode->clock > DP_MAX_PIXEL_CLK_KHZ) + if (msm_dp_wide_bus_available(dp)) + mode_pclk_khz /= 2; + + if (mode_pclk_khz > DP_MAX_PIXEL_CLK_KHZ) return MODE_CLOCK_HIGH; /* -- cgit From 978ca99d6bd87b84ff7788eea4d2c328a70530f6 Mon Sep 17 00:00:00 2001 From: Ethan Carter Edwards Date: Sun, 9 Feb 2025 22:51:54 -0500 Subject: drm/msm/dpu: Fix uninitialized variable There is a possibility for an uninitialized *ret* variable to be returned in some code paths. Fix this by initializing *ret* to 0. Addresses-Coverity-ID: 1642546 ("Uninitialized scalar variable") Fixes: 774bcfb73176 ("drm/msm/dpu: add support for virtual planes") Signed-off-by: Ethan Carter Edwards Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/636201/ Link: https://lore.kernel.org/r/20250209-dpu-v2-1-114dfd4ebefd@ethancedwards.com Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c index 098abc2c0003..af3e541f60c3 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c @@ -1164,7 +1164,6 @@ int dpu_assign_plane_resources(struct dpu_global_state *global_state, unsigned int num_planes) { unsigned int i; - int ret; for (i = 0; i < num_planes; i++) { struct drm_plane_state *plane_state = states[i]; @@ -1173,13 +1172,13 @@ int dpu_assign_plane_resources(struct dpu_global_state *global_state, !plane_state->visible) continue; - ret = dpu_plane_virtual_assign_resources(crtc, global_state, + int ret = dpu_plane_virtual_assign_resources(crtc, global_state, state, plane_state); if (ret) - break; + return ret; } - return ret; + return 0; } static void dpu_plane_flush_csc(struct dpu_plane *pdpu, struct dpu_sw_pipe *pipe) -- cgit From f063ac6b55df03ed25996bdc84d9e1c50147cfa1 Mon Sep 17 00:00:00 2001 From: Jessica Zhang Date: Tue, 11 Feb 2025 19:59:19 -0800 Subject: drm/msm/dpu: Disable dither in phys encoder cleanup Disable pingpong dither in dpu_encoder_helper_phys_cleanup(). This avoids the issue where an encoder unknowingly uses dither after reserving a pingpong block that was previously bound to an encoder that had enabled dither. Cc: stable@vger.kernel.org Reported-by: Dmitry Baryshkov Closes: https://lore.kernel.org/all/jr7zbj5w7iq4apg3gofuvcwf4r2swzqjk7sshwcdjll4mn6ctt@l2n3qfpujg3q/ Signed-off-by: Jessica Zhang Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Fixes: 3c128638a07d ("drm/msm/dpu: add support for dither block in display") Patchwork: https://patchwork.freedesktop.org/patch/636517/ Link: https://lore.kernel.org/r/20250211-dither-disable-v1-1-ac2cb455f6b9@quicinc.com Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c index 5172ab4dea99..48e6e8d74c85 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c @@ -2281,6 +2281,9 @@ void dpu_encoder_helper_phys_cleanup(struct dpu_encoder_phys *phys_enc) } } + if (phys_enc->hw_pp && phys_enc->hw_pp->ops.setup_dither) + phys_enc->hw_pp->ops.setup_dither(phys_enc->hw_pp, NULL); + /* reset the merge 3D HW block */ if (phys_enc->hw_pp && phys_enc->hw_pp->merge_3d) { phys_enc->hw_pp->merge_3d->ops.setup_3d_mode(phys_enc->hw_pp->merge_3d, -- cgit From 144429831f447223253a0e4376489f84ff37d1a7 Mon Sep 17 00:00:00 2001 From: Marijn Suijten Date: Tue, 11 Feb 2025 00:19:32 +0100 Subject: drm/msm/dpu: Don't leak bits_per_component into random DSC_ENC fields What used to be the input_10_bits boolean - feeding into the lowest bit of DSC_ENC - on MSM downstream turned into an accidental OR with the full bits_per_component number when it was ported to the upstream kernel. On typical bpc=8 setups we don't notice this because line_buf_depth is always an odd value (it contains bpc+1) and will also set the 4th bit after left-shifting by 3 (hence this |= bits_per_component is a no-op). Now that guards are being removed to allow more bits_per_component values besides 8 (possible since commit 49fd30a7153b ("drm/msm/dsi: use DRM DSC helpers for DSC setup")), a bpc of 10 will instead clash with the 5th bit which is convert_rgb. This is "fortunately" also always set to true by MSM's dsi_populate_dsc_params() already, but once a bpc of 12 starts being used it'll write into simple_422 which is normally false. To solve all these overlaps, simply replicate downstream code and only set this lowest bit if bits_per_component is equal to 10. It is unclear why DSC requires this only for bpc=10 but not bpc=12, and also notice that this lowest bit wasn't set previously despite having a panel and patch on the list using it without any mentioned issues. Fixes: c110cfd1753e ("drm/msm/disp/dpu1: Add support for DSC") Signed-off-by: Marijn Suijten Reviewed-by: Abhinav Kumar Reviewed-by: Konrad Dybcio Reviewed-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/636311/ Link: https://lore.kernel.org/r/20250211-dsc-10-bit-v1-1-1c85a9430d9a@somainline.org Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c index 657200401f57..cec6d4e8baec 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.c @@ -52,6 +52,7 @@ static void dpu_hw_dsc_config(struct dpu_hw_dsc *hw_dsc, u32 slice_last_group_size; u32 det_thresh_flatness; bool is_cmd_mode = !(mode & DSC_MODE_VIDEO); + bool input_10_bits = dsc->bits_per_component == 10; DPU_REG_WRITE(c, DSC_COMMON_MODE, mode); @@ -68,7 +69,7 @@ static void dpu_hw_dsc_config(struct dpu_hw_dsc *hw_dsc, data |= (dsc->line_buf_depth << 3); data |= (dsc->simple_422 << 2); data |= (dsc->convert_rgb << 1); - data |= dsc->bits_per_component; + data |= input_10_bits; DPU_REG_WRITE(c, DSC_ENC, data); -- cgit From 5e192eefebaab5bdcf716add8910d7f8a2e30e3c Mon Sep 17 00:00:00 2001 From: Jessica Zhang Date: Wed, 8 Jan 2025 14:40:48 -0800 Subject: drm/msm/dpu: Drop extraneous return in dpu_crtc_reassign_planes() Drop extra return at the end of dpu_crtc_reassign_planes() Fixes: 774bcfb73176 ("drm/msm/dpu: add support for virtual planes") Signed-off-by: Jessica Zhang Reviewed-by: Dmitry Baryshkov Patchwork: https://patchwork.freedesktop.org/patch/631565/ Link: https://lore.kernel.org/r/20250108-virtual-planes-fixes-v1-2-420cb36df94a@quicinc.com Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c index 7191b1a6d41b..e5dcd41a361f 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c @@ -1228,8 +1228,6 @@ static int dpu_crtc_reassign_planes(struct drm_crtc *crtc, struct drm_crtc_state done: kfree(states); return ret; - - return 0; } static int dpu_crtc_atomic_check(struct drm_crtc *crtc, -- cgit From 588257897058a0b1aa47912db4fe93c6ff5e3887 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 14 Feb 2025 16:08:41 +0100 Subject: drm/msm/dsi/phy: Protect PHY_CMN_CLK_CFG0 updated from driver side PHY_CMN_CLK_CFG0 register is updated by the PHY driver and by two divider clocks from Common Clock Framework: devm_clk_hw_register_divider_parent_hw(). Concurrent access by the clocks side is protected with spinlock, however driver's side in restoring state is not. Restoring state is called from msm_dsi_phy_enable(), so there could be a path leading to concurrent and conflicting updates with clock framework. Add missing lock usage on the PHY driver side, encapsulated in its own function so the code will be still readable. While shuffling the code, define and use PHY_CMN_CLK_CFG0 bitfields to make the code more readable and obvious. Fixes: 1ef7c99d145c ("drm/msm/dsi: add support for 7nm DSI PHY/PLL") Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Signed-off-by: Krzysztof Kozlowski Patchwork: https://patchwork.freedesktop.org/patch/637376/ Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-1-0943b850722c@linaro.org Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c | 14 ++++++++++++-- drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml | 5 ++++- 2 files changed, 16 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c index 031446c87dae..25ca649de717 100644 --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c @@ -372,6 +372,15 @@ static void dsi_pll_enable_pll_bias(struct dsi_pll_7nm *pll) ndelay(250); } +static void dsi_pll_cmn_clk_cfg0_write(struct dsi_pll_7nm *pll, u32 val) +{ + unsigned long flags; + + spin_lock_irqsave(&pll->postdiv_lock, flags); + writel(val, pll->phy->base + REG_DSI_7nm_PHY_CMN_CLK_CFG0); + spin_unlock_irqrestore(&pll->postdiv_lock, flags); +} + static void dsi_pll_disable_global_clk(struct dsi_pll_7nm *pll) { u32 data; @@ -574,8 +583,9 @@ static int dsi_7nm_pll_restore_state(struct msm_dsi_phy *phy) val |= cached->pll_out_div; writel(val, pll_7nm->phy->pll_base + REG_DSI_7nm_PHY_PLL_PLL_OUTDIV_RATE); - writel(cached->bit_clk_div | (cached->pix_clk_div << 4), - phy_base + REG_DSI_7nm_PHY_CMN_CLK_CFG0); + dsi_pll_cmn_clk_cfg0_write(pll_7nm, + DSI_7nm_PHY_CMN_CLK_CFG0_DIV_CTRL_3_0(cached->bit_clk_div) | + DSI_7nm_PHY_CMN_CLK_CFG0_DIV_CTRL_7_4(cached->pix_clk_div)); val = readl(phy_base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); val &= ~0x3; diff --git a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml index d54b72f92449..e0bf6e016b4c 100644 --- a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml +++ b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml @@ -9,7 +9,10 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd"> - + + + + -- cgit From 5a97bc924ae0804b8dbf627e357acaa5ef761483 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 14 Feb 2025 16:08:42 +0100 Subject: drm/msm/dsi/phy: Protect PHY_CMN_CLK_CFG1 against clock driver PHY_CMN_CLK_CFG1 register is updated by the PHY driver and by a mux clock from Common Clock Framework: devm_clk_hw_register_mux_parent_hws(). There could be a path leading to concurrent and conflicting updates between PHY driver and clock framework, e.g. changing the mux and enabling PLL clocks. Add dedicated spinlock to be sure all PHY_CMN_CLK_CFG1 updates are synchronized. While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to make the code more readable and obvious. Fixes: 1ef7c99d145c ("drm/msm/dsi: add support for 7nm DSI PHY/PLL") Signed-off-by: Krzysztof Kozlowski Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/637378/ Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-2-0943b850722c@linaro.org Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c | 35 ++++++++++++++-------- .../gpu/drm/msm/registers/display/dsi_phy_7nm.xml | 5 +++- 2 files changed, 26 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c index 25ca649de717..388017db45d8 100644 --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c @@ -83,6 +83,9 @@ struct dsi_pll_7nm { /* protects REG_DSI_7nm_PHY_CMN_CLK_CFG0 register */ spinlock_t postdiv_lock; + /* protects REG_DSI_7nm_PHY_CMN_CLK_CFG1 register */ + spinlock_t pclk_mux_lock; + struct pll_7nm_cached_state cached_state; struct dsi_pll_7nm *slave; @@ -381,22 +384,32 @@ static void dsi_pll_cmn_clk_cfg0_write(struct dsi_pll_7nm *pll, u32 val) spin_unlock_irqrestore(&pll->postdiv_lock, flags); } -static void dsi_pll_disable_global_clk(struct dsi_pll_7nm *pll) +static void dsi_pll_cmn_clk_cfg1_update(struct dsi_pll_7nm *pll, u32 mask, + u32 val) { + unsigned long flags; u32 data; + spin_lock_irqsave(&pll->pclk_mux_lock, flags); data = readl(pll->phy->base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); - writel(data & ~BIT(5), pll->phy->base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); + data &= ~mask; + data |= val & mask; + + writel(data, pll->phy->base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); + spin_unlock_irqrestore(&pll->pclk_mux_lock, flags); +} + +static void dsi_pll_disable_global_clk(struct dsi_pll_7nm *pll) +{ + dsi_pll_cmn_clk_cfg1_update(pll, DSI_7nm_PHY_CMN_CLK_CFG1_CLK_EN, 0); } static void dsi_pll_enable_global_clk(struct dsi_pll_7nm *pll) { - u32 data; + u32 cfg_1 = DSI_7nm_PHY_CMN_CLK_CFG1_CLK_EN | DSI_7nm_PHY_CMN_CLK_CFG1_CLK_EN_SEL; writel(0x04, pll->phy->base + REG_DSI_7nm_PHY_CMN_CTRL_3); - - data = readl(pll->phy->base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); - writel(data | BIT(5) | BIT(4), pll->phy->base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); + dsi_pll_cmn_clk_cfg1_update(pll, cfg_1, cfg_1); } static void dsi_pll_phy_dig_reset(struct dsi_pll_7nm *pll) @@ -574,7 +587,6 @@ static int dsi_7nm_pll_restore_state(struct msm_dsi_phy *phy) { struct dsi_pll_7nm *pll_7nm = to_pll_7nm(phy->vco_hw); struct pll_7nm_cached_state *cached = &pll_7nm->cached_state; - void __iomem *phy_base = pll_7nm->phy->base; u32 val; int ret; @@ -586,11 +598,7 @@ static int dsi_7nm_pll_restore_state(struct msm_dsi_phy *phy) dsi_pll_cmn_clk_cfg0_write(pll_7nm, DSI_7nm_PHY_CMN_CLK_CFG0_DIV_CTRL_3_0(cached->bit_clk_div) | DSI_7nm_PHY_CMN_CLK_CFG0_DIV_CTRL_7_4(cached->pix_clk_div)); - - val = readl(phy_base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); - val &= ~0x3; - val |= cached->pll_mux; - writel(val, phy_base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); + dsi_pll_cmn_clk_cfg1_update(pll_7nm, 0x3, cached->pll_mux); ret = dsi_pll_7nm_vco_set_rate(phy->vco_hw, pll_7nm->vco_current_rate, @@ -743,7 +751,7 @@ static int pll_7nm_register(struct dsi_pll_7nm *pll_7nm, struct clk_hw **provide pll_by_2_bit, }), 2, 0, pll_7nm->phy->base + REG_DSI_7nm_PHY_CMN_CLK_CFG1, - 0, 1, 0, NULL); + 0, 1, 0, &pll_7nm->pclk_mux_lock); if (IS_ERR(hw)) { ret = PTR_ERR(hw); goto fail; @@ -788,6 +796,7 @@ static int dsi_pll_7nm_init(struct msm_dsi_phy *phy) pll_7nm_list[phy->id] = pll_7nm; spin_lock_init(&pll_7nm->postdiv_lock); + spin_lock_init(&pll_7nm->pclk_mux_lock); pll_7nm->phy = phy; diff --git a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml index e0bf6e016b4c..cfaf78c028b1 100644 --- a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml +++ b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml @@ -13,7 +13,10 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd"> - + + + + -- cgit From 73f69c6be2a9f22c31c775ec03c6c286bfe12cfa Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 14 Feb 2025 16:08:43 +0100 Subject: drm/msm/dsi/phy: Do not overwite PHY_CMN_CLK_CFG1 when choosing bitclk source PHY_CMN_CLK_CFG1 register has four fields being used in the driver: DSI clock divider, source of bitclk and two for enabling the DSI PHY PLL clocks. dsi_7nm_set_usecase() sets only the source of bitclk, so should leave all other bits untouched. Use newly introduced dsi_pll_cmn_clk_cfg1_update() to update respective bits without overwriting the rest. While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to make the code more readable and obvious. Fixes: 1ef7c99d145c ("drm/msm/dsi: add support for 7nm DSI PHY/PLL") Signed-off-by: Krzysztof Kozlowski Reviewed-by: Dmitry Baryshkov Reviewed-by: Abhinav Kumar Patchwork: https://patchwork.freedesktop.org/patch/637380/ Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-3-0943b850722c@linaro.org Signed-off-by: Abhinav Kumar --- drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c | 4 ++-- drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml | 1 + 2 files changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c index 388017db45d8..798168180c1a 100644 --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c @@ -617,7 +617,6 @@ static int dsi_7nm_pll_restore_state(struct msm_dsi_phy *phy) static int dsi_7nm_set_usecase(struct msm_dsi_phy *phy) { struct dsi_pll_7nm *pll_7nm = to_pll_7nm(phy->vco_hw); - void __iomem *base = phy->base; u32 data = 0x0; /* internal PLL */ DBG("DSI PLL%d", pll_7nm->phy->id); @@ -636,7 +635,8 @@ static int dsi_7nm_set_usecase(struct msm_dsi_phy *phy) } /* set PLL src */ - writel(data << 2, base + REG_DSI_7nm_PHY_CMN_CLK_CFG1); + dsi_pll_cmn_clk_cfg1_update(pll_7nm, DSI_7nm_PHY_CMN_CLK_CFG1_BITCLK_SEL__MASK, + DSI_7nm_PHY_CMN_CLK_CFG1_BITCLK_SEL(data)); return 0; } diff --git a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml index cfaf78c028b1..35f7f40e405b 100644 --- a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml +++ b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml @@ -16,6 +16,7 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd"> + -- cgit From e49477f7f78598295551d486ecc7f020d796432e Mon Sep 17 00:00:00 2001 From: Krzysztof Karas Date: Thu, 16 Jan 2025 10:40:46 +0000 Subject: drm/i915/gt: Use spin_lock_irqsave() in interruptible context spin_lock/unlock() functions used in interrupt contexts could result in a deadlock, as seen in GitLab issue #13399, which occurs when interrupt comes in while holding a lock. Try to remedy the problem by saving irq state before spin lock acquisition. v2: add irqs' state save/restore calls to all locks/unlocks in signal_irq_work() execution (Maciej) v3: use with spin_lock_irqsave() in guc_lrc_desc_unpin() instead of other lock/unlock calls and add Fixes and Cc tags (Tvrtko); change title and commit message Fixes: 2f2cc53b5fe7 ("drm/i915/guc: Close deregister-context race against CT-loss") Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13399 Signed-off-by: Krzysztof Karas Cc: # v6.9+ Reviewed-by: Maciej Patelczyk Reviewed-by: Andi Shyti Signed-off-by: Andi Shyti Link: https://patchwork.freedesktop.org/patch/msgid/pusppq5ybyszau2oocboj3mtj5x574gwij323jlclm5zxvimmu@mnfg6odxbpsv (cherry picked from commit c088387ddd6482b40f21ccf23db1125e8fa4af7e) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/i915/gt/uc/intel_guc_submission.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/gt/uc/intel_guc_submission.c b/drivers/gpu/drm/i915/gt/uc/intel_guc_submission.c index cc05bd9e43b4..3fce5c000144 100644 --- a/drivers/gpu/drm/i915/gt/uc/intel_guc_submission.c +++ b/drivers/gpu/drm/i915/gt/uc/intel_guc_submission.c @@ -3449,10 +3449,10 @@ static inline int guc_lrc_desc_unpin(struct intel_context *ce) */ ret = deregister_context(ce, ce->guc_id.id); if (ret) { - spin_lock(&ce->guc_state.lock); + spin_lock_irqsave(&ce->guc_state.lock, flags); set_context_registered(ce); clr_context_destroyed(ce); - spin_unlock(&ce->guc_state.lock); + spin_unlock_irqrestore(&ce->guc_state.lock, flags); /* * As gt-pm is awake at function entry, intel_wakeref_put_async merely decrements * the wakeref immediately but per function spec usage call this after unlock. -- cgit From 0c455f3a12298e9c89a78d2f3327e15e52c0adc5 Mon Sep 17 00:00:00 2001 From: Lucas De Marchi Date: Thu, 13 Feb 2025 11:28:59 -0800 Subject: drm/xe: Fix error handling in xe_irq_install() When devm_add_action_or_reset() fails, it already calls the function passed as parameter and that function is already free'ing the irqs. Drop the goto and just return. The caller, xe_device_probe(), should also do the same thing instead of wrongly doing `goto err` and calling the unrelated xe_display_fini() function. Fixes: 14d25d8d684d ("drm/xe: change old msi irq api to a new one") Reviewed-by: Rodrigo Vivi Reviewed-by: Himal Prasad Ghimiray Link: https://patchwork.freedesktop.org/patch/msgid/20250213192909.996148-3-lucas.demarchi@intel.com Signed-off-by: Lucas De Marchi (cherry picked from commit 121b214cdf10d4129b64f2b1f31807154c74ae55) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/xe/xe_irq.c | 14 +------------- 1 file changed, 1 insertion(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/xe/xe_irq.c b/drivers/gpu/drm/xe/xe_irq.c index 32f5a67a917b..08552ee3fb94 100644 --- a/drivers/gpu/drm/xe/xe_irq.c +++ b/drivers/gpu/drm/xe/xe_irq.c @@ -757,19 +757,7 @@ int xe_irq_install(struct xe_device *xe) xe_irq_postinstall(xe); - err = devm_add_action_or_reset(xe->drm.dev, irq_uninstall, xe); - if (err) - goto free_irq_handler; - - return 0; - -free_irq_handler: - if (xe_device_has_msix(xe)) - xe_irq_msix_free(xe); - else - xe_irq_msi_free(xe); - - return err; + return devm_add_action_or_reset(xe->drm.dev, irq_uninstall, xe); } static void xe_irq_msi_synchronize_irq(struct xe_device *xe) -- cgit From 879f70382ff3e92fc854589ada3453e3f5f5b601 Mon Sep 17 00:00:00 2001 From: Imre Deak Date: Fri, 14 Feb 2025 16:19:51 +0200 Subject: drm/i915/dsi: Use TRANS_DDI_FUNC_CTL's own port width macro The format of the port width field in the DDI_BUF_CTL and the TRANS_DDI_FUNC_CTL registers are different starting with MTL, where the x3 lane mode for HDMI FRL has a different encoding in the two registers. To account for this use the TRANS_DDI_FUNC_CTL's own port width macro. Cc: # v6.5+ Fixes: b66a8abaa48a ("drm/i915/display/mtl: Fill port width in DDI_BUF_/TRANS_DDI_FUNC_/PORT_BUF_CTL for HDMI") Reviewed-by: Jani Nikula Signed-off-by: Imre Deak Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-2-imre.deak@intel.com (cherry picked from commit 76120b3a304aec28fef4910204b81a12db8974da) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/i915/display/icl_dsi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c index c977b74f82f0..82bf6c654de2 100644 --- a/drivers/gpu/drm/i915/display/icl_dsi.c +++ b/drivers/gpu/drm/i915/display/icl_dsi.c @@ -809,8 +809,8 @@ gen11_dsi_configure_transcoder(struct intel_encoder *encoder, /* select data lane width */ tmp = intel_de_read(display, TRANS_DDI_FUNC_CTL(display, dsi_trans)); - tmp &= ~DDI_PORT_WIDTH_MASK; - tmp |= DDI_PORT_WIDTH(intel_dsi->lane_count); + tmp &= ~TRANS_DDI_PORT_WIDTH_MASK; + tmp |= TRANS_DDI_PORT_WIDTH(intel_dsi->lane_count); /* select input pipe */ tmp &= ~TRANS_DDI_EDP_INPUT_MASK; -- cgit From 166ce267ae3f96e439d8ccc838e8ec4d8b4dab73 Mon Sep 17 00:00:00 2001 From: Imre Deak Date: Fri, 14 Feb 2025 16:19:52 +0200 Subject: drm/i915/ddi: Fix HDMI port width programming in DDI_BUF_CTL Fix the port width programming in the DDI_BUF_CTL register on MTLP+, where this had an off-by-one error. Cc: # v6.5+ Fixes: b66a8abaa48a ("drm/i915/display/mtl: Fill port width in DDI_BUF_/TRANS_DDI_FUNC_/PORT_BUF_CTL for HDMI") Reviewed-by: Jani Nikula Signed-off-by: Imre Deak Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-3-imre.deak@intel.com (cherry picked from commit b2ecdabe46d23db275f94cd7c46ca414a144818b) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/i915/display/intel_ddi.c | 2 +- drivers/gpu/drm/i915/i915_reg.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c index acb986bc1f33..2b9240ab547d 100644 --- a/drivers/gpu/drm/i915/display/intel_ddi.c +++ b/drivers/gpu/drm/i915/display/intel_ddi.c @@ -3487,7 +3487,7 @@ static void intel_ddi_enable_hdmi(struct intel_atomic_state *state, intel_de_rmw(dev_priv, XELPDP_PORT_BUF_CTL1(dev_priv, port), XELPDP_PORT_WIDTH_MASK | XELPDP_PORT_REVERSAL, port_buf); - buf_ctl |= DDI_PORT_WIDTH(lane_count); + buf_ctl |= DDI_PORT_WIDTH(crtc_state->lane_count); if (DISPLAY_VER(dev_priv) >= 20) buf_ctl |= XE2LPD_DDI_BUF_D2D_LINK_ENABLE; diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 765e6c0528fb..786c727aea45 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -3633,7 +3633,7 @@ enum skl_power_gate { #define DDI_BUF_IS_IDLE (1 << 7) #define DDI_BUF_CTL_TC_PHY_OWNERSHIP REG_BIT(6) #define DDI_A_4_LANES (1 << 4) -#define DDI_PORT_WIDTH(width) (((width) - 1) << 1) +#define DDI_PORT_WIDTH(width) (((width) == 3 ? 4 : ((width) - 1)) << 1) #define DDI_PORT_WIDTH_MASK (7 << 1) #define DDI_PORT_WIDTH_SHIFT 1 #define DDI_INIT_DISPLAY_DETECTED (1 << 0) -- cgit From 07fb70d82e0df085980246bf17bc12537588795f Mon Sep 17 00:00:00 2001 From: Ville Syrjälä Date: Wed, 12 Feb 2025 18:43:21 +0200 Subject: drm/i915: Make sure all planes in use by the joiner have their crtc included MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Any active plane needs to have its crtc included in the atomic state. For planes enabled via uapi that is all handler in the core. But when we use a plane for joiner the uapi code things the plane is disabled and therefore doesn't have a crtc. So we need to pull those in by hand. We do it first thing in intel_joiner_add_affected_crtcs() so that any newly added crtc will subsequently pull in all of its joined crtcs as well. The symptoms from failing to do this are: - duct tape in the form of commit 1d5b09f8daf8 ("drm/i915: Fix NULL ptr deref by checking new_crtc_state") - the plane's hw state will get overwritten by the disabled uapi state if it can't find the uapi counterpart plane in the atomic state from where it should copy the correct state Cc: stable@vger.kernel.org Reviewed-by: Maarten Lankhorst Signed-off-by: Ville Syrjälä Link: https://patchwork.freedesktop.org/patch/msgid/20250212164330.16891-2-ville.syrjala@linux.intel.com (cherry picked from commit 91077d1deb5374eb8be00fb391710f00e751dc4b) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/i915/display/intel_display.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c index 4271da219b41..41128469f12a 100644 --- a/drivers/gpu/drm/i915/display/intel_display.c +++ b/drivers/gpu/drm/i915/display/intel_display.c @@ -6628,12 +6628,30 @@ static int intel_async_flip_check_hw(struct intel_atomic_state *state, struct in static int intel_joiner_add_affected_crtcs(struct intel_atomic_state *state) { struct drm_i915_private *i915 = to_i915(state->base.dev); + const struct intel_plane_state *plane_state; struct intel_crtc_state *crtc_state; + struct intel_plane *plane; struct intel_crtc *crtc; u8 affected_pipes = 0; u8 modeset_pipes = 0; int i; + /* + * Any plane which is in use by the joiner needs its crtc. + * Pull those in first as this will not have happened yet + * if the plane remains disabled according to uapi. + */ + for_each_new_intel_plane_in_state(state, plane, plane_state, i) { + crtc = to_intel_crtc(plane_state->hw.crtc); + if (!crtc) + continue; + + crtc_state = intel_atomic_get_crtc_state(&state->base, crtc); + if (IS_ERR(crtc_state)) + return PTR_ERR(crtc_state); + } + + /* Now pull in all joined crtcs */ for_each_new_intel_crtc_in_state(state, crtc, crtc_state, i) { affected_pipes |= crtc_state->joiner_pipes; if (intel_crtc_needs_modeset(crtc_state)) -- cgit From 643f209ba3fdd4099416aaf9efa8266f7366d6fb Mon Sep 17 00:00:00 2001 From: José Roberto de Souza Date: Thu, 23 Jan 2025 12:22:04 -0800 Subject: drm/xe: Make GUC binaries dump consistent with other binaries in devcoredump MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit All other(hwsp, hwctx and vmas) binaries follow this format: [name].length: 0x1000 [name].data: xxxxxxx [name].error: errno The error one is just in case by some reason it was not able to capture the binary. So this GuC binaries should follow the same patern. v2: - renamed GUC binary to LOG Cc: John Harrison Cc: Lucas De Marchi Reviewed-by: Lucas De Marchi Signed-off-by: José Roberto de Souza Link: https://patchwork.freedesktop.org/patch/msgid/20250123202307.95103-3-jose.souza@intel.com Signed-off-by: Lucas De Marchi (cherry picked from commit cb1f868ca13756c0c18ba54d1591332476760d07) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/xe/xe_guc_ct.c | 6 ++++-- drivers/gpu/drm/xe/xe_guc_log.c | 3 ++- 2 files changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/xe/xe_guc_ct.c b/drivers/gpu/drm/xe/xe_guc_ct.c index 50c8076b5158..497036675a38 100644 --- a/drivers/gpu/drm/xe/xe_guc_ct.c +++ b/drivers/gpu/drm/xe/xe_guc_ct.c @@ -1723,9 +1723,11 @@ void xe_guc_ct_snapshot_print(struct xe_guc_ct_snapshot *snapshot, drm_printf(p, "\tg2h outstanding: %d\n", snapshot->g2h_outstanding); - if (snapshot->ctb) - xe_print_blob_ascii85(p, "CTB data", '\n', + if (snapshot->ctb) { + drm_printf(p, "[CTB].length: 0x%lx\n", snapshot->ctb_size); + xe_print_blob_ascii85(p, "[CTB].data", '\n', snapshot->ctb, 0, snapshot->ctb_size); + } } else { drm_puts(p, "CT disabled\n"); } diff --git a/drivers/gpu/drm/xe/xe_guc_log.c b/drivers/gpu/drm/xe/xe_guc_log.c index 2baa4d95571f..2457572ed86a 100644 --- a/drivers/gpu/drm/xe/xe_guc_log.c +++ b/drivers/gpu/drm/xe/xe_guc_log.c @@ -208,10 +208,11 @@ void xe_guc_log_snapshot_print(struct xe_guc_log_snapshot *snapshot, struct drm_ drm_printf(p, "GuC timestamp: 0x%08llX [%llu]\n", snapshot->stamp, snapshot->stamp); drm_printf(p, "Log level: %u\n", snapshot->level); + drm_printf(p, "[LOG].length: 0x%lx\n", snapshot->size); remain = snapshot->size; for (i = 0; i < snapshot->num_chunks; i++) { size_t size = min(GUC_LOG_CHUNK_SIZE, remain); - const char *prefix = i ? NULL : "Log data"; + const char *prefix = i ? NULL : "[LOG].data"; char suffix = i == snapshot->num_chunks - 1 ? '\n' : 0; xe_print_blob_ascii85(p, prefix, suffix, snapshot->copy[i], 0, size); -- cgit From 213e24250feed3bcf58d7594298df2d7e78a88ab Mon Sep 17 00:00:00 2001 From: Lucas De Marchi Date: Tue, 28 Jan 2025 07:42:42 -0800 Subject: drm/xe/guc: Fix size_t print format MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Use %zx format to print size_t to remove the following warning when building for i386: >> drivers/gpu/drm/xe/xe_guc_ct.c:1727:43: warning: format specifies type 'unsigned long' but the argument has type 'size_t' (aka 'unsigned int') [-Wformat] 1727 | drm_printf(p, "[CTB].length: 0x%lx\n", snapshot->ctb_size); | ~~~ ^~~~~~~~~~~~~~~~~~ | %zx Cc: José Roberto de Souza Reported-by: kernel test robot Closes: https://lore.kernel.org/oe-kbuild-all/202501281627.H6nj184e-lkp@intel.com/ Fixes: 643f209ba3fd ("drm/xe: Make GUC binaries dump consistent with other binaries in devcoredump") Reviewed-by: Rodrigo Vivi Link: https://patchwork.freedesktop.org/patch/msgid/20250128154242.3371687-1-lucas.demarchi@intel.com Signed-off-by: Lucas De Marchi (cherry picked from commit 7748289df510638ba61fed86b59ce7d2fb4a194c) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/xe/xe_guc_ct.c | 2 +- drivers/gpu/drm/xe/xe_guc_log.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/xe/xe_guc_ct.c b/drivers/gpu/drm/xe/xe_guc_ct.c index 497036675a38..72ad576fc18e 100644 --- a/drivers/gpu/drm/xe/xe_guc_ct.c +++ b/drivers/gpu/drm/xe/xe_guc_ct.c @@ -1724,7 +1724,7 @@ void xe_guc_ct_snapshot_print(struct xe_guc_ct_snapshot *snapshot, snapshot->g2h_outstanding); if (snapshot->ctb) { - drm_printf(p, "[CTB].length: 0x%lx\n", snapshot->ctb_size); + drm_printf(p, "[CTB].length: 0x%zx\n", snapshot->ctb_size); xe_print_blob_ascii85(p, "[CTB].data", '\n', snapshot->ctb, 0, snapshot->ctb_size); } diff --git a/drivers/gpu/drm/xe/xe_guc_log.c b/drivers/gpu/drm/xe/xe_guc_log.c index 2457572ed86a..0ca3056d8bd3 100644 --- a/drivers/gpu/drm/xe/xe_guc_log.c +++ b/drivers/gpu/drm/xe/xe_guc_log.c @@ -208,7 +208,7 @@ void xe_guc_log_snapshot_print(struct xe_guc_log_snapshot *snapshot, struct drm_ drm_printf(p, "GuC timestamp: 0x%08llX [%llu]\n", snapshot->stamp, snapshot->stamp); drm_printf(p, "Log level: %u\n", snapshot->level); - drm_printf(p, "[LOG].length: 0x%lx\n", snapshot->size); + drm_printf(p, "[LOG].length: 0x%zx\n", snapshot->size); remain = snapshot->size; for (i = 0; i < snapshot->num_chunks; i++) { size_t size = min(GUC_LOG_CHUNK_SIZE, remain); -- cgit From 3dbc0215e3c502a9f3221576da0fdc9847fb9721 Mon Sep 17 00:00:00 2001 From: Aaron Kling Date: Tue, 18 Feb 2025 03:28:03 -0600 Subject: drm/nouveau/pmu: Fix gp10b firmware guard Most kernel configs enable multiple Tegra SoC generations, causing this typo to go unnoticed. But in the case where a kernel config is strictly for Tegra186, this is a problem. Fixes: 989863d7cbe5 ("drm/nouveau/pmu: select implementation based on available firmware") Signed-off-by: Aaron Kling Signed-off-by: Danilo Krummrich Link: https://patchwork.freedesktop.org/patch/msgid/20250218-nouveau-gm10b-guard-v2-1-a4de71500d48@gmail.com --- drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp10b.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp10b.c b/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp10b.c index a6f410ba60bc..d393bc540f86 100644 --- a/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp10b.c +++ b/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/gp10b.c @@ -75,7 +75,7 @@ gp10b_pmu_acr = { .bootstrap_multiple_falcons = gp10b_pmu_acr_bootstrap_multiple_falcons, }; -#if IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC) +#if IS_ENABLED(CONFIG_ARCH_TEGRA_186_SOC) MODULE_FIRMWARE("nvidia/gp10b/pmu/desc.bin"); MODULE_FIRMWARE("nvidia/gp10b/pmu/image.bin"); MODULE_FIRMWARE("nvidia/gp10b/pmu/sig.bin"); -- cgit From 838c17fd077e611b12c78feb0feee1b30ed09b63 Mon Sep 17 00:00:00 2001 From: Su Hui Date: Tue, 11 Feb 2025 09:53:55 +0800 Subject: accel/amdxdna: Add missing include linux/slab.h MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When compiling without CONFIG_IA32_EMULATION, there can be some errors: drivers/accel/amdxdna/amdxdna_mailbox.c: In function ‘mailbox_release_msg’: drivers/accel/amdxdna/amdxdna_mailbox.c:197:2: error: implicit declaration of function ‘kfree’. 197 | kfree(mb_msg); | ^~~~~ drivers/accel/amdxdna/amdxdna_mailbox.c: In function ‘xdna_mailbox_send_msg’: drivers/accel/amdxdna/amdxdna_mailbox.c:418:11: error:implicit declaration of function ‘kzalloc’. 418 | mb_msg = kzalloc(sizeof(*mb_msg) + pkg_size, GFP_KERNEL); | ^~~~~~~ Add the missing include. Fixes: b87f920b9344 ("accel/amdxdna: Support hardware mailbox") Signed-off-by: Su Hui Reviewed-by: Lizhi Hou Reviewed-by: Jeffrey Hugo Signed-off-by: Lizhi Hou Link: https://patchwork.freedesktop.org/patch/msgid/20250211015354.3388171-1-suhui@nfschina.com --- drivers/accel/amdxdna/amdxdna_mailbox.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/accel/amdxdna/amdxdna_mailbox.c b/drivers/accel/amdxdna/amdxdna_mailbox.c index 814b16bb1953..e5301fac1397 100644 --- a/drivers/accel/amdxdna/amdxdna_mailbox.c +++ b/drivers/accel/amdxdna/amdxdna_mailbox.c @@ -8,6 +8,7 @@ #include #include #include +#include #include #define CREATE_TRACE_POINTS -- cgit From b9275eabe31e6679ae12c46a4a0a18d622db4570 Mon Sep 17 00:00:00 2001 From: Imre Deak Date: Tue, 18 Feb 2025 00:38:27 +0200 Subject: drm/i915/dp: Fix error handling during 128b/132b link training At the end of a 128b/132b link training sequence, the HW expects the transcoder training pattern to be set to TPS2 and from that to normal mode (disabling the training pattern). Transitioning from TPS1 directly to normal mode leaves the transcoder in a stuck state, resulting in page-flip timeouts later in the modeset sequence. Atm, in case of a failure during link training, the transcoder may be still set to output the TPS1 pattern. Later the transcoder is then set from TPS1 directly to normal mode in intel_dp_stop_link_train(), leading to modeset failures later as described above. Fix this by setting the training patter to TPS2, if the link training failed at any point. The clue in the specification about the above HW behavior is the explicit mention that TPS2 must be set after the link training sequence (and there isn't a similar requirement specified for the 8b/10b link training), see the Bspec links below. v2: Add bspec aspect/link to the commit log. (Jani) Bspec: 54128, 65448, 68849 Cc: stable@vger.kernel.org # v5.18+ Cc: Jani Nikula Signed-off-by: Imre Deak Acked-by: Jani Nikula Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-2-imre.deak@intel.com Signed-off-by: Rodrigo Vivi (cherry picked from commit 8b4bbaf8ddc1f68f3ee96a706f65fdb1bcd9d355) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/i915/display/intel_dp_link_training.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/display/intel_dp_link_training.c b/drivers/gpu/drm/i915/display/intel_dp_link_training.c index 8b1977cfec50..6696a32cdd3e 100644 --- a/drivers/gpu/drm/i915/display/intel_dp_link_training.c +++ b/drivers/gpu/drm/i915/display/intel_dp_link_training.c @@ -1563,7 +1563,7 @@ intel_dp_128b132b_link_train(struct intel_dp *intel_dp, if (wait_for(intel_dp_128b132b_intra_hop(intel_dp, crtc_state) == 0, 500)) { lt_err(intel_dp, DP_PHY_DPRX, "128b/132b intra-hop not clear\n"); - return false; + goto out; } if (intel_dp_128b132b_lane_eq(intel_dp, crtc_state) && @@ -1575,6 +1575,19 @@ intel_dp_128b132b_link_train(struct intel_dp *intel_dp, passed ? "passed" : "failed", crtc_state->port_clock, crtc_state->lane_count); +out: + /* + * Ensure that the training pattern does get set to TPS2 even in case + * of a failure, as is the case at the end of a passing link training + * and what is expected by the transcoder. Leaving TPS1 set (and + * disabling the link train mode in DP_TP_CTL later from TPS1 directly) + * would result in a stuck transcoder HW state and flip-done timeouts + * later in the modeset sequence. + */ + if (!passed) + intel_dp_program_link_training_pattern(intel_dp, crtc_state, + DP_PHY_DPRX, DP_TRAINING_PATTERN_2); + return passed; } -- cgit From 8058b49bf6fff777bf3f47309c7b15dbef2191af Mon Sep 17 00:00:00 2001 From: Imre Deak Date: Tue, 18 Feb 2025 00:38:28 +0200 Subject: drm/i915/dp: Fix disabling the transcoder function in 128b/132b mode During disabling the transcoder in DP 128b/132b mode (both in case of an MST master transcoder and in case of SST) the transcoder function must be first disabled without changing any other field in the register (in particular leaving the DDI port and mode select fields unchanged) and clearing the DDI port and mode select fields separately, later during the disabling sequences. Fix the sequence accordingly. Bspec: 54128, 65448, 68849 Cc: Jani Nikula Fixes: 79a6734cd56e ("drm/i915/ddi: disable trancoder port select for 128b/132b SST") Signed-off-by: Imre Deak Reviewed-by: Jani Nikula Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-3-imre.deak@intel.com Signed-off-by: Rodrigo Vivi (cherry picked from commit 2ed653c7b843db0670136330480842d76cb65cd8) Signed-off-by: Rodrigo Vivi --- drivers/gpu/drm/i915/display/intel_ddi.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c index 2b9240ab547d..18c66992aa1d 100644 --- a/drivers/gpu/drm/i915/display/intel_ddi.c +++ b/drivers/gpu/drm/i915/display/intel_ddi.c @@ -658,7 +658,6 @@ void intel_ddi_disable_transcoder_func(const struct intel_crtc_state *crtc_state struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc); struct drm_i915_private *dev_priv = to_i915(crtc->base.dev); enum transcoder cpu_transcoder = crtc_state->cpu_transcoder; - bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST); u32 ctl; if (DISPLAY_VER(dev_priv) >= 11) @@ -678,8 +677,7 @@ void intel_ddi_disable_transcoder_func(const struct intel_crtc_state *crtc_state TRANS_DDI_PORT_SYNC_MASTER_SELECT_MASK); if (DISPLAY_VER(dev_priv) >= 12) { - if (!intel_dp_mst_is_master_trans(crtc_state) || - (!is_mst && intel_dp_is_uhbr(crtc_state))) { + if (!intel_dp_mst_is_master_trans(crtc_state)) { ctl &= ~(TGL_TRANS_DDI_PORT_MASK | TRANS_DDI_MODE_SELECT_MASK); } @@ -3134,7 +3132,7 @@ static void intel_ddi_post_disable_dp(struct intel_atomic_state *state, intel_dp_set_power(intel_dp, DP_SET_POWER_D3); if (DISPLAY_VER(dev_priv) >= 12) { - if (is_mst) { + if (is_mst || intel_dp_is_uhbr(old_crtc_state)) { enum transcoder cpu_transcoder = old_crtc_state->cpu_transcoder; intel_de_rmw(dev_priv, -- cgit