From ba714a9c1dea85e0bf2899d02dfeb9c70040427c Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Tue, 23 May 2017 23:23:32 +0200 Subject: pinctrl/amd: Use regular interrupt instead of chained The AMD pinctrl driver uses a chained interrupt to demultiplex the GPIO interrupts. Kevin Vandeventer reported, that his new AMD Ryzen locks up hard on boot when the AMD pinctrl driver is initialized. The reason is an interrupt storm. It's not clear whether that's caused by hardware or firmware or both. Using chained interrupts on X86 is a dangerous endavour. If a system is misconfigured or the hardware buggy there is no safety net to catch an interrupt storm. Convert the driver to use a regular interrupt for the demultiplex handler. This allows the interrupt storm detector to catch the malfunction and lets the system boot up. This should be backported to stable because it's likely that more users run into this problem as the AMD Ryzen machines are spreading. Reported-by: Kevin Vandeventer Link: https://bugzilla.suse.com/show_bug.cgi?id=1034261 Signed-off-by: Thomas Gleixner Signed-off-by: Linus Walleij --- drivers/pinctrl/pinctrl-amd.c | 91 +++++++++++++++++++------------------------ 1 file changed, 41 insertions(+), 50 deletions(-) (limited to 'drivers') diff --git a/drivers/pinctrl/pinctrl-amd.c b/drivers/pinctrl/pinctrl-amd.c index 1482d132fbb8..e432ec887479 100644 --- a/drivers/pinctrl/pinctrl-amd.c +++ b/drivers/pinctrl/pinctrl-amd.c @@ -495,64 +495,54 @@ static struct irq_chip amd_gpio_irqchip = { .flags = IRQCHIP_SKIP_SET_WAKE, }; -static void amd_gpio_irq_handler(struct irq_desc *desc) +#define PIN_IRQ_PENDING (BIT(INTERRUPT_STS_OFF) | BIT(WAKE_STS_OFF)) + +static irqreturn_t amd_gpio_irq_handler(int irq, void *dev_id) { - u32 i; - u32 off; - u32 reg; - u32 pin_reg; - u64 reg64; - int handled = 0; - unsigned int irq; + struct amd_gpio *gpio_dev = dev_id; + struct gpio_chip *gc = &gpio_dev->gc; + irqreturn_t ret = IRQ_NONE; + unsigned int i, irqnr; unsigned long flags; - struct irq_chip *chip = irq_desc_get_chip(desc); - struct gpio_chip *gc = irq_desc_get_handler_data(desc); - struct amd_gpio *gpio_dev = gpiochip_get_data(gc); + u32 *regs, regval; + u64 status, mask; - chained_irq_enter(chip, desc); - /*enable GPIO interrupt again*/ + /* Read the wake status */ raw_spin_lock_irqsave(&gpio_dev->lock, flags); - reg = readl(gpio_dev->base + WAKE_INT_STATUS_REG1); - reg64 = reg; - reg64 = reg64 << 32; - - reg = readl(gpio_dev->base + WAKE_INT_STATUS_REG0); - reg64 |= reg; + status = readl(gpio_dev->base + WAKE_INT_STATUS_REG1); + status <<= 32; + status |= readl(gpio_dev->base + WAKE_INT_STATUS_REG0); raw_spin_unlock_irqrestore(&gpio_dev->lock, flags); - /* - * first 46 bits indicates interrupt status. - * one bit represents four interrupt sources. - */ - for (off = 0; off < 46 ; off++) { - if (reg64 & BIT(off)) { - for (i = 0; i < 4; i++) { - pin_reg = readl(gpio_dev->base + - (off * 4 + i) * 4); - if ((pin_reg & BIT(INTERRUPT_STS_OFF)) || - (pin_reg & BIT(WAKE_STS_OFF))) { - irq = irq_find_mapping(gc->irqdomain, - off * 4 + i); - generic_handle_irq(irq); - writel(pin_reg, - gpio_dev->base - + (off * 4 + i) * 4); - handled++; - } - } + /* Bit 0-45 contain the relevant status bits */ + status &= (1ULL << 46) - 1; + regs = gpio_dev->base; + for (mask = 1, irqnr = 0; status; mask <<= 1, regs += 4, irqnr += 4) { + if (!(status & mask)) + continue; + status &= ~mask; + + /* Each status bit covers four pins */ + for (i = 0; i < 4; i++) { + regval = readl(regs + i); + if (!(regval & PIN_IRQ_PENDING)) + continue; + irq = irq_find_mapping(gc->irqdomain, irqnr + i); + generic_handle_irq(irq); + /* Clear interrupt */ + writel(regval, regs + i); + ret = IRQ_HANDLED; } } - if (handled == 0) - handle_bad_irq(desc); - + /* Signal EOI to the GPIO unit */ raw_spin_lock_irqsave(&gpio_dev->lock, flags); - reg = readl(gpio_dev->base + WAKE_INT_MASTER_REG); - reg |= EOI_MASK; - writel(reg, gpio_dev->base + WAKE_INT_MASTER_REG); + regval = readl(gpio_dev->base + WAKE_INT_MASTER_REG); + regval |= EOI_MASK; + writel(regval, gpio_dev->base + WAKE_INT_MASTER_REG); raw_spin_unlock_irqrestore(&gpio_dev->lock, flags); - chained_irq_exit(chip, desc); + return ret; } static int amd_get_groups_count(struct pinctrl_dev *pctldev) @@ -821,10 +811,11 @@ static int amd_gpio_probe(struct platform_device *pdev) goto out2; } - gpiochip_set_chained_irqchip(&gpio_dev->gc, - &amd_gpio_irqchip, - irq_base, - amd_gpio_irq_handler); + ret = devm_request_irq(&pdev->dev, irq_base, amd_gpio_irq_handler, 0, + KBUILD_MODNAME, gpio_dev); + if (ret) + goto out2; + platform_set_drvdata(pdev, gpio_dev); dev_dbg(&pdev->dev, "amd gpio driver loaded\n"); -- cgit From b7c747d4627462f25b3daabf49c18895a6722faa Mon Sep 17 00:00:00 2001 From: Alexandre TORGUE Date: Tue, 30 May 2017 16:43:04 +0200 Subject: pinctrl: stm32: Fix bad function call In stm32_pconf_parse_conf function, stm32_pmx_gpio_set_direction is called with wrong parameter value. Indeed, using NULL value for range will raise an oops. Fixes: aceb16dc2da5 ("pinctrl: Add STM32 MCUs support") Reported-by: Dan Carpenter Signed-off-by: Alexandre TORGUE Signed-off-by: Linus Walleij --- drivers/pinctrl/stm32/pinctrl-stm32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c index d3c5f5dfbbd7..222b6685b09f 100644 --- a/drivers/pinctrl/stm32/pinctrl-stm32.c +++ b/drivers/pinctrl/stm32/pinctrl-stm32.c @@ -798,7 +798,7 @@ static int stm32_pconf_parse_conf(struct pinctrl_dev *pctldev, break; case PIN_CONFIG_OUTPUT: __stm32_gpio_set(bank, offset, arg); - ret = stm32_pmx_gpio_set_direction(pctldev, NULL, pin, false); + ret = stm32_pmx_gpio_set_direction(pctldev, range, pin, false); break; default: ret = -EINVAL; -- cgit