From ffba2123e1714a27e9362fda57c42155dda37efc Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 22 Mar 2022 20:32:55 -0700 Subject: net: stmmac: dwmac-qcom-ethqos: Enable RGMII functional clock on resume When the Qualcomm ethqos driver is properly described in its associated GDSC power-domain, the hardware will be powered down and loose its state between qcom_ethqos_probe() and stmmac_init_dma_engine(). The result of this is that the functional clock from the RGMII IO macro is no longer provides and the DMA software reset in dwmac4_dma_reset() will time out, due to lacking clock signal. Re-enable the functional clock, as part of the Qualcomm specific clock enablement sequence to avoid this problem. The final clock configuration will be adjusted by ethqos_fix_mac_speed() once the link is being brought up. Fixes: a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos") Signed-off-by: Bjorn Andersson Tested-and-reviewed-by: Bhupesh Sharma Link: https://lore.kernel.org/r/20220323033255.2282930-1-bjorn.andersson@linaro.org Signed-off-by: Jakub Kicinski --- drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c index 0cc28c79cc61..835caa15d55f 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c @@ -487,6 +487,13 @@ static int ethqos_clks_config(void *priv, bool enabled) dev_err(ðqos->pdev->dev, "rgmii_clk enable failed\n"); return ret; } + + /* Enable functional clock to prevent DMA reset to timeout due + * to lacking PHY clock after the hardware block has been power + * cycled. The actual configuration will be adjusted once + * ethqos_fix_mac_speed() is invoked. + */ + ethqos_set_func_clk_en(ethqos); } else { clk_disable_unprepare(ethqos->rgmii_clk); } -- cgit From 109d899452ba17996eccec7ae8249fb1f8900a16 Mon Sep 17 00:00:00 2001 From: Alvin Šipraga Date: Wed, 23 Mar 2022 13:42:25 +0100 Subject: net: dsa: realtek: make interface drivers depend on OF MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The kernel test robot reported build warnings with a randconfig that built realtek-{smi,mdio} without CONFIG_OF set. Since both interface drivers are using OF and will not probe without, add the corresponding dependency to Kconfig. Link: https://lore.kernel.org/all/202203231233.Xx73Y40o-lkp@intel.com/ Link: https://lore.kernel.org/all/202203231439.ycl0jg50-lkp@intel.com/ Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers") Fixes: 765c39a4fafe ("net: dsa: realtek: convert subdrivers into modules") Signed-off-by: Alvin Šipraga Reviewed-by: Andrew Lunn Acked-by: Luiz Angelo Daros de Luca Link: https://lore.kernel.org/r/20220323124225.91763-1-alvin@pqrs.dk Signed-off-by: Jakub Kicinski --- drivers/net/dsa/realtek/Kconfig | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/dsa/realtek/Kconfig b/drivers/net/dsa/realtek/Kconfig index b7427a8292b2..1aa79735355f 100644 --- a/drivers/net/dsa/realtek/Kconfig +++ b/drivers/net/dsa/realtek/Kconfig @@ -12,6 +12,7 @@ menuconfig NET_DSA_REALTEK config NET_DSA_REALTEK_MDIO tristate "Realtek MDIO connected switch driver" depends on NET_DSA_REALTEK + depends on OF help Select to enable support for registering switches configured through MDIO. @@ -19,6 +20,7 @@ config NET_DSA_REALTEK_MDIO config NET_DSA_REALTEK_SMI tristate "Realtek SMI connected switch driver" depends on NET_DSA_REALTEK + depends on OF help Select to enable support for registering switches connected through SMI. -- cgit From 9fe087dda5bf097007b263664051bc0e84f6580d Mon Sep 17 00:00:00 2001 From: Greg Jesionowski Date: Wed, 23 Mar 2022 15:00:24 -0700 Subject: net: usb: ax88179_178a: add Allied Telesis AT-UMCs Adds the driver_info and IDs for the AX88179 based Allied Telesis AT-UMC family of devices. Signed-off-by: Greg Jesionowski Link: https://lore.kernel.org/r/20220323220024.GA36800@test-HP-EliteDesk-800-G1-SFF Signed-off-by: Jakub Kicinski --- drivers/net/usb/ax88179_178a.c | 51 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+) (limited to 'drivers') diff --git a/drivers/net/usb/ax88179_178a.c b/drivers/net/usb/ax88179_178a.c index a31098981a65..e2fa56b92685 100644 --- a/drivers/net/usb/ax88179_178a.c +++ b/drivers/net/usb/ax88179_178a.c @@ -1872,6 +1872,45 @@ static const struct driver_info mct_info = { .tx_fixup = ax88179_tx_fixup, }; +static const struct driver_info at_umc2000_info = { + .description = "AT-UMC2000 USB 3.0/USB 3.1 Gen 1 to Gigabit Ethernet Adapter", + .bind = ax88179_bind, + .unbind = ax88179_unbind, + .status = ax88179_status, + .link_reset = ax88179_link_reset, + .reset = ax88179_reset, + .stop = ax88179_stop, + .flags = FLAG_ETHER | FLAG_FRAMING_AX, + .rx_fixup = ax88179_rx_fixup, + .tx_fixup = ax88179_tx_fixup, +}; + +static const struct driver_info at_umc200_info = { + .description = "AT-UMC200 USB 3.0/USB 3.1 Gen 1 to Fast Ethernet Adapter", + .bind = ax88179_bind, + .unbind = ax88179_unbind, + .status = ax88179_status, + .link_reset = ax88179_link_reset, + .reset = ax88179_reset, + .stop = ax88179_stop, + .flags = FLAG_ETHER | FLAG_FRAMING_AX, + .rx_fixup = ax88179_rx_fixup, + .tx_fixup = ax88179_tx_fixup, +}; + +static const struct driver_info at_umc2000sp_info = { + .description = "AT-UMC2000/SP USB 3.0/USB 3.1 Gen 1 to Gigabit Ethernet Adapter", + .bind = ax88179_bind, + .unbind = ax88179_unbind, + .status = ax88179_status, + .link_reset = ax88179_link_reset, + .reset = ax88179_reset, + .stop = ax88179_stop, + .flags = FLAG_ETHER | FLAG_FRAMING_AX, + .rx_fixup = ax88179_rx_fixup, + .tx_fixup = ax88179_tx_fixup, +}; + static const struct usb_device_id products[] = { { /* ASIX AX88179 10/100/1000 */ @@ -1913,6 +1952,18 @@ static const struct usb_device_id products[] = { /* Magic Control Technology U3-A9003 USB 3.0 Gigabit Ethernet Adapter */ USB_DEVICE(0x0711, 0x0179), .driver_info = (unsigned long)&mct_info, +}, { + /* Allied Telesis AT-UMC2000 USB 3.0/USB 3.1 Gen 1 to Gigabit Ethernet Adapter */ + USB_DEVICE(0x07c9, 0x000e), + .driver_info = (unsigned long)&at_umc2000_info, +}, { + /* Allied Telesis AT-UMC200 USB 3.0/USB 3.1 Gen 1 to Fast Ethernet Adapter */ + USB_DEVICE(0x07c9, 0x000f), + .driver_info = (unsigned long)&at_umc200_info, +}, { + /* Allied Telesis AT-UMC2000/SP USB 3.0/USB 3.1 Gen 1 to Gigabit Ethernet Adapter */ + USB_DEVICE(0x07c9, 0x0010), + .driver_info = (unsigned long)&at_umc2000sp_info, }, { }, }; -- cgit From feb13dcb1818b775fbd9191f797be67cd605f03e Mon Sep 17 00:00:00 2001 From: Vladimir Oltean Date: Thu, 24 Mar 2022 18:12:10 +0200 Subject: net: enetc: report software timestamping via SO_TIMESTAMPING Let user space properly determine that the enetc driver provides software timestamps. Fixes: 4caefbce06d1 ("enetc: add software timestamping") Signed-off-by: Vladimir Oltean Reviewed-by: Claudiu Manoil Link: https://lore.kernel.org/r/20220324161210.4122281-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski --- drivers/net/ethernet/freescale/enetc/enetc_ethtool.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/freescale/enetc/enetc_ethtool.c b/drivers/net/ethernet/freescale/enetc/enetc_ethtool.c index fa5b4f885b17..60ec64bfb3f0 100644 --- a/drivers/net/ethernet/freescale/enetc/enetc_ethtool.c +++ b/drivers/net/ethernet/freescale/enetc/enetc_ethtool.c @@ -674,7 +674,10 @@ static int enetc_get_ts_info(struct net_device *ndev, #ifdef CONFIG_FSL_ENETC_PTP_CLOCK info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE | SOF_TIMESTAMPING_RX_HARDWARE | - SOF_TIMESTAMPING_RAW_HARDWARE; + SOF_TIMESTAMPING_RAW_HARDWARE | + SOF_TIMESTAMPING_TX_SOFTWARE | + SOF_TIMESTAMPING_RX_SOFTWARE | + SOF_TIMESTAMPING_SOFTWARE; info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON) | -- cgit From 264a9c5c9dff40f92a2a9ad1757d59a4438114fd Mon Sep 17 00:00:00 2001 From: Casper Andersson Date: Thu, 24 Mar 2022 12:38:52 +0100 Subject: net: sparx5: Remove unused GLAG handling in PGID Removes PGID handling for GLAG since it is not used yet. According to feedback on previous patch. https://lore.kernel.org/netdev/20220322081823.wqbx7vud4q7qtjuq@wse-c0155/T/#t Signed-off-by: Casper Andersson Reviewed-by: Steen Hegelund Signed-off-by: Jakub Kicinski --- drivers/net/ethernet/microchip/sparx5/sparx5_main.h | 4 ---- drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c | 17 ----------------- 2 files changed, 21 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h index 7a04b8f2a546..8e77d7ee8e68 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h @@ -69,9 +69,6 @@ enum sparx5_vlan_port_type { #define PGID_TABLE_SIZE 3290 #define PGID_MCAST_START 65 -#define PGID_GLAG_START 833 -#define PGID_GLAG_END 1088 - #define IFH_LEN 9 /* 36 bytes */ #define NULL_VID 0 #define SPX5_MACT_PULL_DELAY (2 * HZ) @@ -374,7 +371,6 @@ enum sparx5_pgid_type { SPX5_PGID_FREE, SPX5_PGID_RESERVED, SPX5_PGID_MULTICAST, - SPX5_PGID_GLAG }; void sparx5_pgid_init(struct sparx5 *spx5); diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c b/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c index 90366fcb9958..851a559269e1 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c @@ -15,28 +15,11 @@ void sparx5_pgid_init(struct sparx5 *spx5) spx5->pgid_map[i] = SPX5_PGID_RESERVED; } -int sparx5_pgid_alloc_glag(struct sparx5 *spx5, u16 *idx) -{ - int i; - - for (i = PGID_GLAG_START; i <= PGID_GLAG_END; i++) - if (spx5->pgid_map[i] == SPX5_PGID_FREE) { - spx5->pgid_map[i] = SPX5_PGID_GLAG; - *idx = i; - return 0; - } - - return -EBUSY; -} - int sparx5_pgid_alloc_mcast(struct sparx5 *spx5, u16 *idx) { int i; for (i = PGID_MCAST_START; i < PGID_TABLE_SIZE; i++) { - if (i == PGID_GLAG_START) - i = PGID_GLAG_END + 1; - if (spx5->pgid_map[i] == SPX5_PGID_FREE) { spx5->pgid_map[i] = SPX5_PGID_MULTICAST; *idx = i; -- cgit From ad238fc6de7d1adece5167df09464912c098b021 Mon Sep 17 00:00:00 2001 From: Casper Andersson Date: Thu, 24 Mar 2022 12:38:53 +0100 Subject: net: sparx5: Refactor mdb handling according to feedback - Remove mact_lookup and use new mact_find instead. - Make pgid_read_mask function. - Set PGID arbiter to start searching at PGID_BASE + 8. This is according to feedback on previous patch. https://lore.kernel.org/netdev/20220322081823.wqbx7vud4q7qtjuq@wse-c0155/T/#t Signed-off-by: Casper Andersson Reviewed-by: Steen Hegelund Signed-off-by: Jakub Kicinski --- .../net/ethernet/microchip/sparx5/sparx5_mactable.c | 19 ++++--------------- drivers/net/ethernet/microchip/sparx5/sparx5_main.h | 3 ++- drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c | 3 +++ .../net/ethernet/microchip/sparx5/sparx5_switchdev.c | 18 ++++++++---------- drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c | 7 +++++++ 5 files changed, 24 insertions(+), 26 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_mactable.c b/drivers/net/ethernet/microchip/sparx5/sparx5_mactable.c index 35abb3d0ce19..a5837dbe0c7e 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_mactable.c +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_mactable.c @@ -212,19 +212,7 @@ bool sparx5_mact_find(struct sparx5 *sparx5, mutex_unlock(&sparx5->lock); - return ret == 0; -} - -static int sparx5_mact_lookup(struct sparx5 *sparx5, - const unsigned char mac[ETH_ALEN], - u16 vid) -{ - u32 pcfg2; - - if (sparx5_mact_find(sparx5, mac, vid, &pcfg2)) - return 1; - - return 0; + return ret; } int sparx5_mact_forget(struct sparx5 *sparx5, @@ -305,9 +293,10 @@ int sparx5_add_mact_entry(struct sparx5 *sparx5, { struct sparx5_mact_entry *mact_entry; int ret; + u32 cfg2; - ret = sparx5_mact_lookup(sparx5, addr, vid); - if (ret) + ret = sparx5_mact_find(sparx5, addr, vid, &cfg2); + if (!ret) return 0; /* In case the entry already exists, don't add it again to SW, diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h index 8e77d7ee8e68..b197129044b5 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h @@ -65,10 +65,10 @@ enum sparx5_vlan_port_type { #define PGID_IPV6_MC_CTRL (PGID_BASE + 5) #define PGID_BCAST (PGID_BASE + 6) #define PGID_CPU (PGID_BASE + 7) +#define PGID_MCAST_START (PGID_BASE + 8) #define PGID_TABLE_SIZE 3290 -#define PGID_MCAST_START 65 #define IFH_LEN 9 /* 36 bytes */ #define NULL_VID 0 #define SPX5_MACT_PULL_DELAY (2 * HZ) @@ -325,6 +325,7 @@ void sparx5_mact_init(struct sparx5 *sparx5); /* sparx5_vlan.c */ void sparx5_pgid_update_mask(struct sparx5_port *port, int pgid, bool enable); +void sparx5_pgid_read_mask(struct sparx5 *sparx5, int pgid, u32 portmask[3]); void sparx5_update_fwd(struct sparx5 *sparx5); void sparx5_vlan_init(struct sparx5 *sparx5); void sparx5_vlan_port_setup(struct sparx5 *sparx5, int portno); diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c b/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c index 851a559269e1..af8b435009f4 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_pgid.c @@ -19,6 +19,9 @@ int sparx5_pgid_alloc_mcast(struct sparx5 *spx5, u16 *idx) { int i; + /* The multicast area starts at index 65, but the first 7 + * are reserved for flood masks and CPU. Start alloc after that. + */ for (i = PGID_MCAST_START; i < PGID_TABLE_SIZE; i++) { if (spx5->pgid_map[i] == SPX5_PGID_FREE) { spx5->pgid_map[i] = SPX5_PGID_MULTICAST; diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c b/drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c index 2d8e0b81c839..5389fffc694a 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c @@ -406,11 +406,11 @@ static int sparx5_handle_port_mdb_add(struct net_device *dev, res = sparx5_mact_find(spx5, v->addr, vid, &mact_entry); - if (res) { + if (res == 0) { pgid_idx = LRN_MAC_ACCESS_CFG_2_MAC_ENTRY_ADDR_GET(mact_entry); - /* MC_IDX has an offset of 65 in the PGID table. */ - pgid_idx += PGID_MCAST_START; + /* MC_IDX starts after the port masks in the PGID table */ + pgid_idx += SPX5_PORTS; sparx5_pgid_update_mask(port, pgid_idx, true); } else { err = sparx5_pgid_alloc_mcast(spx5, &pgid_idx); @@ -468,17 +468,15 @@ static int sparx5_handle_port_mdb_del(struct net_device *dev, res = sparx5_mact_find(spx5, v->addr, vid, &mact_entry); - if (res) { + if (res == 0) { pgid_idx = LRN_MAC_ACCESS_CFG_2_MAC_ENTRY_ADDR_GET(mact_entry); - /* MC_IDX has an offset of 65 in the PGID table. */ - pgid_idx += PGID_MCAST_START; + /* MC_IDX starts after the port masks in the PGID table */ + pgid_idx += SPX5_PORTS; sparx5_pgid_update_mask(port, pgid_idx, false); - pgid_entry[0] = spx5_rd(spx5, ANA_AC_PGID_CFG(pgid_idx)); - pgid_entry[1] = spx5_rd(spx5, ANA_AC_PGID_CFG1(pgid_idx)); - pgid_entry[2] = spx5_rd(spx5, ANA_AC_PGID_CFG2(pgid_idx)); - if (pgid_entry[0] == 0 && pgid_entry[1] == 0 && pgid_entry[2] == 0) { + sparx5_pgid_read_mask(spx5, pgid_idx, pgid_entry); + if (bitmap_empty((unsigned long *)pgid_entry, SPX5_PORTS)) { /* No ports are in MC group. Remove entry */ err = sparx5_mdb_del_entry(dev, spx5, v->addr, vid, pgid_idx); if (err) diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c b/drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c index 8e56ffa1c4f7..37e4ac965849 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_vlan.c @@ -138,6 +138,13 @@ void sparx5_pgid_update_mask(struct sparx5_port *port, int pgid, bool enable) } } +void sparx5_pgid_read_mask(struct sparx5 *spx5, int pgid, u32 portmask[3]) +{ + portmask[0] = spx5_rd(spx5, ANA_AC_PGID_CFG(pgid)); + portmask[1] = spx5_rd(spx5, ANA_AC_PGID_CFG1(pgid)); + portmask[2] = spx5_rd(spx5, ANA_AC_PGID_CFG2(pgid)); +} + void sparx5_update_fwd(struct sparx5 *sparx5) { DECLARE_BITMAP(workmask, SPX5_PORTS); -- cgit From ccb18f05535c96d26e2d559d402acb87700fc5a7 Mon Sep 17 00:00:00 2001 From: Jian Shen Date: Thu, 24 Mar 2022 20:54:47 +0800 Subject: net: hns3: fix bug when PF set the duplicate MAC address for VFs If the MAC address A is configured to vport A and then vport B. The MAC address of vport A in the hardware becomes invalid. If the address of vport A is changed to MAC address B, the driver needs to delete the MAC address A of vport A. Due to the MAC address A of vport A has become invalid in the hardware entry, so "-ENOENT" is returned. In this case, the "used_umv_size" value recorded in driver is not updated. As a result, the MAC entry status of the software is inconsistent with that of the hardware. Therefore, the driver updates the umv size even if the MAC entry cannot be found. Ensure that the software and hardware status is consistent. Fixes: ee4bcd3b7ae4 ("net: hns3: refactor the MAC address configure") Signed-off-by: Jian Shen Signed-off-by: Guangbin Huang Signed-off-by: Jakub Kicinski --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 78d0498bdabc..0e1a110e7847 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -8438,12 +8438,11 @@ int hclge_rm_uc_addr_common(struct hclge_vport *vport, hnae3_set_bit(req.entry_type, HCLGE_MAC_VLAN_BIT0_EN_B, 0); hclge_prepare_mac_addr(&req, addr, false); ret = hclge_remove_mac_vlan_tbl(vport, &req); - if (!ret) { + if (!ret || ret == -ENOENT) { mutex_lock(&hdev->vport_lock); hclge_update_umv_space(vport, true); mutex_unlock(&hdev->vport_lock); - } else if (ret == -ENOENT) { - ret = 0; + return 0; } return ret; -- cgit From c0f46de30c965d4ba208b5bf1a6d3437a7556ee2 Mon Sep 17 00:00:00 2001 From: Jian Shen Date: Thu, 24 Mar 2022 20:54:48 +0800 Subject: net: hns3: fix port base vlan add fail when concurrent with reset Currently, Port base vlan is initiated by PF and configured to its VFs, by using command "ip link set vf vlan ". When a global reset was triggered, the hardware vlan table and the soft recorded vlan information will be cleared by PF, and restored them until VFs were ready. There is a short time window between the table had been cleared and before table restored. If configured a new port base vlan tag at this moment, driver will check the soft recorded vlan information, and find there hasn't the old tag in it, which causing a warning print. Due to the port base vlan is managed by PF, so the VFs's port base vlan restoring should be handled by PF when PF was ready. This patch fixes it. Fixes: 039ba863e8d7 ("net: hns3: optimize the filter table entries handling when resetting") Signed-off-by: Jian Shen Signed-off-by: Guangbin Huang Signed-off-by: Jakub Kicinski --- .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 62 +++++++++++++++------- .../ethernet/hisilicon/hns3/hns3pf/hclge_main.h | 3 ++ 2 files changed, 46 insertions(+), 19 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 0e1a110e7847..34c6280c9af2 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1872,6 +1872,7 @@ static int hclge_alloc_vport(struct hclge_dev *hdev) vport->vf_info.link_state = IFLA_VF_LINK_STATE_AUTO; vport->mps = HCLGE_MAC_DEFAULT_FRAME; vport->port_base_vlan_cfg.state = HNAE3_PORT_BASE_VLAN_DISABLE; + vport->port_base_vlan_cfg.tbl_sta = true; vport->rxvlan_cfg.rx_vlan_offload_en = true; vport->req_vlan_fltr_en = true; INIT_LIST_HEAD(&vport->vlan_list); @@ -9915,34 +9916,52 @@ void hclge_uninit_vport_vlan_table(struct hclge_dev *hdev) } } -void hclge_restore_vport_vlan_table(struct hclge_vport *vport) +void hclge_restore_vport_port_base_vlan_config(struct hclge_dev *hdev) { - struct hclge_vport_vlan_cfg *vlan, *tmp; - struct hclge_dev *hdev = vport->back; + struct hclge_vlan_info *vlan_info; + struct hclge_vport *vport; u16 vlan_proto; u16 vlan_id; u16 state; + int vf_id; int ret; - vlan_proto = vport->port_base_vlan_cfg.vlan_info.vlan_proto; - vlan_id = vport->port_base_vlan_cfg.vlan_info.vlan_tag; - state = vport->port_base_vlan_cfg.state; + /* PF should restore all vfs port base vlan */ + for (vf_id = 0; vf_id < hdev->num_alloc_vfs; vf_id++) { + vport = &hdev->vport[vf_id + HCLGE_VF_VPORT_START_NUM]; + vlan_info = vport->port_base_vlan_cfg.tbl_sta ? + &vport->port_base_vlan_cfg.vlan_info : + &vport->port_base_vlan_cfg.old_vlan_info; - if (state != HNAE3_PORT_BASE_VLAN_DISABLE) { - clear_bit(vport->vport_id, hdev->vlan_table[vlan_id]); - hclge_set_vlan_filter_hw(hdev, htons(vlan_proto), - vport->vport_id, vlan_id, - false); - return; + vlan_id = vlan_info->vlan_tag; + vlan_proto = vlan_info->vlan_proto; + state = vport->port_base_vlan_cfg.state; + + if (state != HNAE3_PORT_BASE_VLAN_DISABLE) { + clear_bit(vport->vport_id, hdev->vlan_table[vlan_id]); + ret = hclge_set_vlan_filter_hw(hdev, htons(vlan_proto), + vport->vport_id, + vlan_id, false); + vport->port_base_vlan_cfg.tbl_sta = ret == 0; + } } +} - list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { - ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q), - vport->vport_id, - vlan->vlan_id, false); - if (ret) - break; - vlan->hd_tbl_status = true; +void hclge_restore_vport_vlan_table(struct hclge_vport *vport) +{ + struct hclge_vport_vlan_cfg *vlan, *tmp; + struct hclge_dev *hdev = vport->back; + int ret; + + if (vport->port_base_vlan_cfg.state == HNAE3_PORT_BASE_VLAN_DISABLE) { + list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { + ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q), + vport->vport_id, + vlan->vlan_id, false); + if (ret) + break; + vlan->hd_tbl_status = true; + } } } @@ -9983,6 +10002,7 @@ static void hclge_restore_hw_table(struct hclge_dev *hdev) struct hnae3_handle *handle = &vport->nic; hclge_restore_mac_table_common(vport); + hclge_restore_vport_port_base_vlan_config(hdev); hclge_restore_vport_vlan_table(vport); set_bit(HCLGE_STATE_FD_USER_DEF_CHANGED, &hdev->state); hclge_restore_fd_entries(handle); @@ -10039,6 +10059,8 @@ static int hclge_update_vlan_filter_entries(struct hclge_vport *vport, false); } + vport->port_base_vlan_cfg.tbl_sta = false; + /* force add VLAN 0 */ ret = hclge_set_vf_vlan_common(hdev, vport->vport_id, false, 0); if (ret) @@ -10128,7 +10150,9 @@ out: else nic->port_base_vlan_state = HNAE3_PORT_BASE_VLAN_ENABLE; + vport->port_base_vlan_cfg.old_vlan_info = *old_vlan_info; vport->port_base_vlan_cfg.vlan_info = *vlan_info; + vport->port_base_vlan_cfg.tbl_sta = true; hclge_set_vport_vlan_fltr_change(vport); return 0; diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h index fc92ae385e30..a0f619c77eae 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h @@ -985,7 +985,9 @@ struct hclge_vlan_info { struct hclge_port_base_vlan_config { u16 state; + bool tbl_sta; struct hclge_vlan_info vlan_info; + struct hclge_vlan_info old_vlan_info; }; struct hclge_vf_info { @@ -1100,6 +1102,7 @@ void hclge_rm_vport_all_mac_table(struct hclge_vport *vport, bool is_del_list, void hclge_rm_vport_all_vlan_table(struct hclge_vport *vport, bool is_del_list); void hclge_uninit_vport_vlan_table(struct hclge_dev *hdev); void hclge_restore_mac_table_common(struct hclge_vport *vport); +void hclge_restore_vport_port_base_vlan_config(struct hclge_dev *hdev); void hclge_restore_vport_vlan_table(struct hclge_vport *vport); int hclge_update_port_base_vlan_cfg(struct hclge_vport *vport, u16 state, struct hclge_vlan_info *vlan_info); -- cgit From 1932a624ab88ff407d1a1d567fe581faa15dc725 Mon Sep 17 00:00:00 2001 From: Jian Shen Date: Thu, 24 Mar 2022 20:54:49 +0800 Subject: net: hns3: add vlan list lock to protect vlan list When adding port base VLAN, vf VLAN need to remove from HW and modify the vlan state in vf VLAN list as false. If the periodicity task is freeing the same node, it may cause "use after free" error. This patch adds a vlan list lock to protect the vlan list. Fixes: c6075b193462 ("net: hns3: Record VF vlan tables") Signed-off-by: Jian Shen Signed-off-by: Guangbin Huang Signed-off-by: Jakub Kicinski --- .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 38 +++++++++++++++++++--- .../ethernet/hisilicon/hns3/hns3pf/hclge_main.h | 1 + 2 files changed, 35 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 34c6280c9af2..67d60e00170f 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -9818,19 +9818,28 @@ static void hclge_add_vport_vlan_table(struct hclge_vport *vport, u16 vlan_id, bool writen_to_tbl) { struct hclge_vport_vlan_cfg *vlan, *tmp; + struct hclge_dev *hdev = vport->back; - list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) - if (vlan->vlan_id == vlan_id) + mutex_lock(&hdev->vport_lock); + + list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { + if (vlan->vlan_id == vlan_id) { + mutex_unlock(&hdev->vport_lock); return; + } + } vlan = kzalloc(sizeof(*vlan), GFP_KERNEL); - if (!vlan) + if (!vlan) { + mutex_unlock(&hdev->vport_lock); return; + } vlan->hd_tbl_status = writen_to_tbl; vlan->vlan_id = vlan_id; list_add_tail(&vlan->node, &vport->vlan_list); + mutex_unlock(&hdev->vport_lock); } static int hclge_add_vport_all_vlan_table(struct hclge_vport *vport) @@ -9839,6 +9848,8 @@ static int hclge_add_vport_all_vlan_table(struct hclge_vport *vport) struct hclge_dev *hdev = vport->back; int ret; + mutex_lock(&hdev->vport_lock); + list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { if (!vlan->hd_tbl_status) { ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q), @@ -9848,12 +9859,16 @@ static int hclge_add_vport_all_vlan_table(struct hclge_vport *vport) dev_err(&hdev->pdev->dev, "restore vport vlan list failed, ret=%d\n", ret); + + mutex_unlock(&hdev->vport_lock); return ret; } } vlan->hd_tbl_status = true; } + mutex_unlock(&hdev->vport_lock); + return 0; } @@ -9863,6 +9878,8 @@ static void hclge_rm_vport_vlan_table(struct hclge_vport *vport, u16 vlan_id, struct hclge_vport_vlan_cfg *vlan, *tmp; struct hclge_dev *hdev = vport->back; + mutex_lock(&hdev->vport_lock); + list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { if (vlan->vlan_id == vlan_id) { if (is_write_tbl && vlan->hd_tbl_status) @@ -9877,6 +9894,8 @@ static void hclge_rm_vport_vlan_table(struct hclge_vport *vport, u16 vlan_id, break; } } + + mutex_unlock(&hdev->vport_lock); } void hclge_rm_vport_all_vlan_table(struct hclge_vport *vport, bool is_del_list) @@ -9884,6 +9903,8 @@ void hclge_rm_vport_all_vlan_table(struct hclge_vport *vport, bool is_del_list) struct hclge_vport_vlan_cfg *vlan, *tmp; struct hclge_dev *hdev = vport->back; + mutex_lock(&hdev->vport_lock); + list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { if (vlan->hd_tbl_status) hclge_set_vlan_filter_hw(hdev, @@ -9899,6 +9920,7 @@ void hclge_rm_vport_all_vlan_table(struct hclge_vport *vport, bool is_del_list) } } clear_bit(vport->vport_id, hdev->vf_vlan_full); + mutex_unlock(&hdev->vport_lock); } void hclge_uninit_vport_vlan_table(struct hclge_dev *hdev) @@ -9907,6 +9929,8 @@ void hclge_uninit_vport_vlan_table(struct hclge_dev *hdev) struct hclge_vport *vport; int i; + mutex_lock(&hdev->vport_lock); + for (i = 0; i < hdev->num_alloc_vport; i++) { vport = &hdev->vport[i]; list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { @@ -9914,6 +9938,8 @@ void hclge_uninit_vport_vlan_table(struct hclge_dev *hdev) kfree(vlan); } } + + mutex_unlock(&hdev->vport_lock); } void hclge_restore_vport_port_base_vlan_config(struct hclge_dev *hdev) @@ -9953,6 +9979,8 @@ void hclge_restore_vport_vlan_table(struct hclge_vport *vport) struct hclge_dev *hdev = vport->back; int ret; + mutex_lock(&hdev->vport_lock); + if (vport->port_base_vlan_cfg.state == HNAE3_PORT_BASE_VLAN_DISABLE) { list_for_each_entry_safe(vlan, tmp, &vport->vlan_list, node) { ret = hclge_set_vlan_filter_hw(hdev, htons(ETH_P_8021Q), @@ -9963,6 +9991,8 @@ void hclge_restore_vport_vlan_table(struct hclge_vport *vport) vlan->hd_tbl_status = true; } } + + mutex_unlock(&hdev->vport_lock); } /* For global reset and imp reset, hardware will clear the mac table, @@ -11861,8 +11891,8 @@ static void hclge_uninit_ae_dev(struct hnae3_ae_dev *ae_dev) hclge_misc_irq_uninit(hdev); hclge_devlink_uninit(hdev); hclge_pci_uninit(hdev); - mutex_destroy(&hdev->vport_lock); hclge_uninit_vport_vlan_table(hdev); + mutex_destroy(&hdev->vport_lock); ae_dev->priv = NULL; } diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h index a0f619c77eae..c70239758bb2 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h @@ -1033,6 +1033,7 @@ struct hclge_vport { spinlock_t mac_list_lock; /* protect mac address need to add/detele */ struct list_head uc_mac_list; /* Store VF unicast table */ struct list_head mc_mac_list; /* Store VF multicast table */ + struct list_head vlan_list; /* Store VF vlan table */ }; -- cgit From 190cd8a72b0181c543ecada6243be3a50636941b Mon Sep 17 00:00:00 2001 From: Jian Shen Date: Thu, 24 Mar 2022 20:54:50 +0800 Subject: net: hns3: refine the process when PF set VF VLAN Currently, when PF set VF VLAN, it sends notify mailbox to VF if VF alive. VF stop its traffic, and send request mailbox to PF, then PF updates VF VLAN. It's a bit complex. If VF is killed before sending request, PF will not set VF VLAN without any log. This patch refines the process, PF can set VF VLAN direclty, and then notify the VF. If VF is resetting at that time, the notify may be dropped, so VF should query it after reset finished. Fixes: 92f11ea177cd ("net: hns3: fix set port based VLAN issue for VF") Signed-off-by: Jian Shen Signed-off-by: Guangbin Huang Signed-off-by: Jakub Kicinski --- .../net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 18 +++++++++++++----- .../net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c | 5 +++++ 2 files changed, 18 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 67d60e00170f..279a1771fe7c 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -8993,11 +8993,16 @@ static int hclge_set_vf_mac(struct hnae3_handle *handle, int vf, ether_addr_copy(vport->vf_info.mac, mac_addr); + /* there is a timewindow for PF to know VF unalive, it may + * cause send mailbox fail, but it doesn't matter, VF will + * query it when reinit. + */ if (test_bit(HCLGE_VPORT_STATE_ALIVE, &vport->state)) { dev_info(&hdev->pdev->dev, "MAC of VF %d has been set to %s, and it will be reinitialized!\n", vf, format_mac_addr); - return hclge_inform_reset_assert_to_vf(vport); + (void)hclge_inform_reset_assert_to_vf(vport); + return 0; } dev_info(&hdev->pdev->dev, "MAC of VF %d has been set to %s\n", @@ -10250,14 +10255,17 @@ static int hclge_set_vf_vlan_filter(struct hnae3_handle *handle, int vfid, return ret; } - /* for DEVICE_VERSION_V3, vf doesn't need to know about the port based + /* there is a timewindow for PF to know VF unalive, it may + * cause send mailbox fail, but it doesn't matter, VF will + * query it when reinit. + * for DEVICE_VERSION_V3, vf doesn't need to know about the port based * VLAN state. */ if (ae_dev->dev_version < HNAE3_DEVICE_VERSION_V3 && test_bit(HCLGE_VPORT_STATE_ALIVE, &vport->state)) - hclge_push_vf_port_base_vlan_info(&hdev->vport[0], - vport->vport_id, state, - &vlan_info); + (void)hclge_push_vf_port_base_vlan_info(&hdev->vport[0], + vport->vport_id, + state, &vlan_info); return 0; } diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c index 93389bec8d89..342d7cdf6285 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c @@ -2862,6 +2862,11 @@ static int hclgevf_reset_hdev(struct hclgevf_dev *hdev) return ret; } + /* get current port based vlan state from PF */ + ret = hclgevf_get_port_base_vlan_filter_state(hdev); + if (ret) + return ret; + set_bit(HCLGEVF_STATE_PROMISC_CHANGED, &hdev->state); hclgevf_init_rxd_adv_layout(hdev); -- cgit From bf8bfc4336f7a34e48b3bbd19b1542bf085bdc3d Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Thu, 24 Mar 2022 16:24:38 -0700 Subject: net: phy: broadcom: Fix brcm_fet_config_init() A Broadcom AC201 PHY (same entry as 5241) would be flagged by the Broadcom UniMAC MDIO controller as not completing the turn around properly since the PHY expects 65 MDC clock cycles to complete a write cycle, and the MDIO controller was only sending 64 MDC clock cycles as determined by looking at a scope shot. This would make the subsequent read fail with the UniMAC MDIO controller command field having MDIO_READ_FAIL set and we would abort the brcm_fet_config_init() function and thus not probe the PHY at all. After issuing a software reset, wait for at least 1ms which is well above the 1us reset delay advertised by the datasheet and issue a dummy read to let the PHY turn around the line properly. This read specifically ignores -EIO which would be returned by MDIO controllers checking for the line being turned around. If we have a genuine reaad failure, the next read of the interrupt status register would pick it up anyway. Fixes: d7a2ed9248a3 ("broadcom: Add AC131 phy support") Signed-off-by: Florian Fainelli Link: https://lore.kernel.org/r/20220324232438.1156812-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski --- drivers/net/phy/broadcom.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) (limited to 'drivers') diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c index 3c683e0e40e9..e36809aa6d30 100644 --- a/drivers/net/phy/broadcom.c +++ b/drivers/net/phy/broadcom.c @@ -11,6 +11,7 @@ */ #include "bcm-phy-lib.h" +#include #include #include #include @@ -602,6 +603,26 @@ static int brcm_fet_config_init(struct phy_device *phydev) if (err < 0) return err; + /* The datasheet indicates the PHY needs up to 1us to complete a reset, + * build some slack here. + */ + usleep_range(1000, 2000); + + /* The PHY requires 65 MDC clock cycles to complete a write operation + * and turnaround the line properly. + * + * We ignore -EIO here as the MDIO controller (e.g.: mdio-bcm-unimac) + * may flag the lack of turn-around as a read failure. This is + * particularly true with this combination since the MDIO controller + * only used 64 MDC cycles. This is not a critical failure in this + * specific case and it has no functional impact otherwise, so we let + * that one go through. If there is a genuine bus error, the next read + * of MII_BRCM_FET_INTREG will error out. + */ + err = phy_read(phydev, MII_BMCR); + if (err < 0 && err != -EIO) + return err; + reg = phy_read(phydev, MII_BRCM_FET_INTREG); if (reg < 0) return reg; -- cgit From 8778372118023e2258612c03573c47efef41d755 Mon Sep 17 00:00:00 2001 From: Hao Chen Date: Sat, 26 Mar 2022 17:51:00 +0800 Subject: net: hns3: fix ethtool tx copybreak buf size indicating not aligned issue When use ethtoool set tx copybreak buf size to a large value which causes order exceeding 10 or memory is not enough, it causes allocating tx copybreak buffer failed and print "the active tx spare buf is 0, not enabled tx spare buffer", however, use --get-tunable parameter query tx copybreak buf size and it indicates setting value not 0. So, it's necessary to change the print value from setting value to 0. Set kinfo.tx_spare_buf_size to 0 when set tx copybreak buf size failed. Fixes: e445f08af2b1 ("net: hns3: add support to set/get tx copybreak buf size via ethtool for hns3 driver") Signed-off-by: Hao Chen Signed-off-by: Guangbin Huang Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3_enet.c | 20 ++++++++++++-------- drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c | 3 ++- 2 files changed, 14 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c index 0b8a73c40b12..16137238ddbf 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c @@ -1028,13 +1028,12 @@ static bool hns3_can_use_tx_sgl(struct hns3_enet_ring *ring, static void hns3_init_tx_spare_buffer(struct hns3_enet_ring *ring) { + u32 alloc_size = ring->tqp->handle->kinfo.tx_spare_buf_size; struct hns3_tx_spare *tx_spare; struct page *page; - u32 alloc_size; dma_addr_t dma; int order; - alloc_size = ring->tqp->handle->kinfo.tx_spare_buf_size; if (!alloc_size) return; @@ -1044,30 +1043,35 @@ static void hns3_init_tx_spare_buffer(struct hns3_enet_ring *ring) if (!tx_spare) { /* The driver still work without the tx spare buffer */ dev_warn(ring_to_dev(ring), "failed to allocate hns3_tx_spare\n"); - return; + goto devm_kzalloc_error; } page = alloc_pages_node(dev_to_node(ring_to_dev(ring)), GFP_KERNEL, order); if (!page) { dev_warn(ring_to_dev(ring), "failed to allocate tx spare pages\n"); - devm_kfree(ring_to_dev(ring), tx_spare); - return; + goto alloc_pages_error; } dma = dma_map_page(ring_to_dev(ring), page, 0, PAGE_SIZE << order, DMA_TO_DEVICE); if (dma_mapping_error(ring_to_dev(ring), dma)) { dev_warn(ring_to_dev(ring), "failed to map pages for tx spare\n"); - put_page(page); - devm_kfree(ring_to_dev(ring), tx_spare); - return; + goto dma_mapping_error; } tx_spare->dma = dma; tx_spare->buf = page_address(page); tx_spare->len = PAGE_SIZE << order; ring->tx_spare = tx_spare; + return; + +dma_mapping_error: + put_page(page); +alloc_pages_error: + devm_kfree(ring_to_dev(ring), tx_spare); +devm_kzalloc_error: + ring->tqp->handle->kinfo.tx_spare_buf_size = 0; } /* Use hns3_tx_spare_space() to make sure there is enough buffer diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c index 6469238ae090..ae30dbe7ef52 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c @@ -1818,7 +1818,8 @@ static int hns3_set_tunable(struct net_device *netdev, old_tx_spare_buf_size = h->kinfo.tx_spare_buf_size; new_tx_spare_buf_size = *(u32 *)data; ret = hns3_set_tx_spare_buf_size(netdev, new_tx_spare_buf_size); - if (ret) { + if (ret || + (!priv->ring->tx_spare && new_tx_spare_buf_size != 0)) { int ret1; netdev_warn(netdev, -- cgit From a89cbb16995bf15582e0d1bdb922ad1a54a2fa8c Mon Sep 17 00:00:00 2001 From: Hao Chen Date: Sat, 26 Mar 2022 17:51:01 +0800 Subject: net: hns3: add max order judgement for tx spare buffer Add max order judgement for tx spare buffer to avoid triggering call trace, print related fail information instead, when user set tx spare buf size to a large value which causes order exceeding 10. Fixes: e445f08af2b1 ("net: hns3: add support to set/get tx copybreak buf size via ethtool for hns3 driver") Signed-off-by: Hao Chen Signed-off-by: Guangbin Huang Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3_enet.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c index 16137238ddbf..530ba8bef503 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c @@ -1038,6 +1038,12 @@ static void hns3_init_tx_spare_buffer(struct hns3_enet_ring *ring) return; order = get_order(alloc_size); + if (order >= MAX_ORDER) { + if (net_ratelimit()) + dev_warn(ring_to_dev(ring), "failed to allocate tx spare buffer, exceed to max order\n"); + return; + } + tx_spare = devm_kzalloc(ring_to_dev(ring), sizeof(*tx_spare), GFP_KERNEL); if (!tx_spare) { -- cgit From 671cb8cbb9c9e24b681d21b1bfae991e2386ac73 Mon Sep 17 00:00:00 2001 From: Peng Li Date: Sat, 26 Mar 2022 17:51:02 +0800 Subject: net: hns3: clean residual vf config after disable sriov After disable sriov, VF still has some config and info need to be cleaned, which configured by PF. This patch clean the HW config and SW struct vport->vf_info. Fixes: fa8d82e853e8 ("net: hns3: Add support of .sriov_configure in HNS3 driver") Signed-off-by: Peng Li Signed-off-by: Guangbin Huang Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hnae3.h | 3 ++ drivers/net/ethernet/hisilicon/hns3/hns3_enet.c | 18 ++++++++ .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 50 ++++++++++++++++++++++ 3 files changed, 71 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hnae3.h b/drivers/net/ethernet/hisilicon/hns3/hnae3.h index 6f18c9a03231..d44dd7091fa1 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hnae3.h +++ b/drivers/net/ethernet/hisilicon/hns3/hnae3.h @@ -537,6 +537,8 @@ struct hnae3_ae_dev { * Get 1588 rx hwstamp * get_ts_info * Get phc info + * clean_vf_config + * Clean residual vf info after disable sriov */ struct hnae3_ae_ops { int (*init_ae_dev)(struct hnae3_ae_dev *ae_dev); @@ -730,6 +732,7 @@ struct hnae3_ae_ops { struct ethtool_ts_info *info); int (*get_link_diagnosis_info)(struct hnae3_handle *handle, u32 *status_code); + void (*clean_vf_config)(struct hnae3_ae_dev *ae_dev, int num_vfs); }; struct hnae3_dcb_ops { diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c index 530ba8bef503..14dc12c2155d 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3_enet.c @@ -3060,6 +3060,21 @@ static int hns3_probe(struct pci_dev *pdev, const struct pci_device_id *ent) return ret; } +/** + * hns3_clean_vf_config + * @pdev: pointer to a pci_dev structure + * @num_vfs: number of VFs allocated + * + * Clean residual vf config after disable sriov + **/ +static void hns3_clean_vf_config(struct pci_dev *pdev, int num_vfs) +{ + struct hnae3_ae_dev *ae_dev = pci_get_drvdata(pdev); + + if (ae_dev->ops->clean_vf_config) + ae_dev->ops->clean_vf_config(ae_dev, num_vfs); +} + /* hns3_remove - Device removal routine * @pdev: PCI device information struct */ @@ -3098,7 +3113,10 @@ static int hns3_pci_sriov_configure(struct pci_dev *pdev, int num_vfs) else return num_vfs; } else if (!pci_vfs_assigned(pdev)) { + int num_vfs_pre = pci_num_vf(pdev); + pci_disable_sriov(pdev); + hns3_clean_vf_config(pdev, num_vfs_pre); } else { dev_warn(&pdev->dev, "Unable to free VFs because some are assigned to VMs.\n"); diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 279a1771fe7c..2a5e6a241d52 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -12724,6 +12724,55 @@ static int hclge_get_link_diagnosis_info(struct hnae3_handle *handle, return 0; } +/* After disable sriov, VF still has some config and info need clean, + * which configed by PF. + */ +static void hclge_clear_vport_vf_info(struct hclge_vport *vport, int vfid) +{ + struct hclge_dev *hdev = vport->back; + struct hclge_vlan_info vlan_info; + int ret; + + /* after disable sriov, clean VF rate configured by PF */ + ret = hclge_tm_qs_shaper_cfg(vport, 0); + if (ret) + dev_err(&hdev->pdev->dev, + "failed to clean vf%d rate config, ret = %d\n", + vfid, ret); + + vlan_info.vlan_tag = 0; + vlan_info.qos = 0; + vlan_info.vlan_proto = ETH_P_8021Q; + ret = hclge_update_port_base_vlan_cfg(vport, + HNAE3_PORT_BASE_VLAN_DISABLE, + &vlan_info); + if (ret) + dev_err(&hdev->pdev->dev, + "failed to clean vf%d port base vlan, ret = %d\n", + vfid, ret); + + ret = hclge_set_vf_spoofchk_hw(hdev, vport->vport_id, false); + if (ret) + dev_err(&hdev->pdev->dev, + "failed to clean vf%d spoof config, ret = %d\n", + vfid, ret); + + memset(&vport->vf_info, 0, sizeof(vport->vf_info)); +} + +static void hclge_clean_vport_config(struct hnae3_ae_dev *ae_dev, int num_vfs) +{ + struct hclge_dev *hdev = ae_dev->priv; + struct hclge_vport *vport; + int i; + + for (i = 0; i < num_vfs; i++) { + vport = &hdev->vport[i + HCLGE_VF_VPORT_START_NUM]; + + hclge_clear_vport_vf_info(vport, i); + } +} + static const struct hnae3_ae_ops hclge_ops = { .init_ae_dev = hclge_init_ae_dev, .uninit_ae_dev = hclge_uninit_ae_dev, @@ -12825,6 +12874,7 @@ static const struct hnae3_ae_ops hclge_ops = { .get_rx_hwts = hclge_ptp_get_rx_hwts, .get_ts_info = hclge_ptp_get_ts_info, .get_link_diagnosis_info = hclge_get_link_diagnosis_info, + .clean_vf_config = hclge_clean_vport_config, }; static struct hnae3_ae_algo ae_algo = { -- cgit From f5cd60169f981ca737c9e49c446506dfafc90a35 Mon Sep 17 00:00:00 2001 From: Hao Chen Date: Sat, 26 Mar 2022 17:51:03 +0800 Subject: net: hns3: add netdev reset check for hns3_set_tunable() When pci device reset failed, it does uninit operation and priv->ring is NULL, it causes accessing NULL pointer error. Add netdev reset check for hns3_set_tunable() to fix it. Fixes: 99f6b5fb5f63 ("net: hns3: use bounce buffer when rx page can not be reused") Signed-off-by: Hao Chen Signed-off-by: Guangbin Huang Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c index ae30dbe7ef52..49e7b022caaa 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c @@ -1766,9 +1766,6 @@ static int hns3_set_tx_spare_buf_size(struct net_device *netdev, struct hnae3_handle *h = priv->ae_handle; int ret; - if (hns3_nic_resetting(netdev)) - return -EBUSY; - h->kinfo.tx_spare_buf_size = data; ret = hns3_reset_notify(h, HNAE3_DOWN_CLIENT); @@ -1799,6 +1796,11 @@ static int hns3_set_tunable(struct net_device *netdev, struct hnae3_handle *h = priv->ae_handle; int i, ret = 0; + if (hns3_nic_resetting(netdev) || !priv->ring) { + netdev_err(netdev, "failed to set tunable value, dev resetting!"); + return -EBUSY; + } + switch (tuna->id) { case ETHTOOL_TX_COPYBREAK: priv->tx_copybreak = *(u32 *)data; -- cgit From 4d07c5936c2508ddd1cfd49b0a91d94cb4d1f0e8 Mon Sep 17 00:00:00 2001 From: Hao Chen Date: Sat, 26 Mar 2022 17:51:04 +0800 Subject: net: hns3: add NULL pointer check for hns3_set/get_ringparam() When pci devices init failed and haven't reinit, priv->ring is NULL and hns3_set/get_ringparam() will access priv->ring. it causes call trace. So, add NULL pointer check for hns3_set/get_ringparam() to avoid this situation. Fixes: 5668abda0931 ("net: hns3: add support for set_ringparam") Signed-off-by: Hao Chen Signed-off-by: Guangbin Huang Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c index 49e7b022caaa..f4da77452126 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c @@ -653,8 +653,8 @@ static void hns3_get_ringparam(struct net_device *netdev, struct hnae3_handle *h = priv->ae_handle; int rx_queue_index = h->kinfo.num_tqps; - if (hns3_nic_resetting(netdev)) { - netdev_err(netdev, "dev resetting!"); + if (hns3_nic_resetting(netdev) || !priv->ring) { + netdev_err(netdev, "failed to get ringparam value, due to dev resetting or uninited\n"); return; } @@ -1074,8 +1074,14 @@ static int hns3_check_ringparam(struct net_device *ndev, { #define RX_BUF_LEN_2K 2048 #define RX_BUF_LEN_4K 4096 - if (hns3_nic_resetting(ndev)) + + struct hns3_nic_priv *priv = netdev_priv(ndev); + + if (hns3_nic_resetting(ndev) || !priv->ring) { + netdev_err(ndev, "failed to set ringparam value, due to dev resetting or uninited\n"); return -EBUSY; + } + if (param->rx_mini_pending || param->rx_jumbo_pending) return -EINVAL; -- cgit From ad0ecaef6a2c07e67ef9fe163c007f7b3dad8643 Mon Sep 17 00:00:00 2001 From: Guangbin Huang Date: Sat, 26 Mar 2022 17:51:05 +0800 Subject: net: hns3: fix phy can not link up when autoneg off and reset Currently, function hclge_mdio_read() will return 0 if during reset(the cmd state will be set to disable). If use general phy driver, the phy_state_machine() will update phy speed every second in function genphy_read_status_fixed() when PHY is set to autoneg off, no matter of link down or link up. If phy driver happens to read BMCR register during reset, phy speed will be updated to 10Mpbs as BMCR register value is 0. So it may call phy can not link up if previous speed is not 10Mpbs. To fix this problem, function hclge_mdio_read() should return -EBUSY if the cmd state is disable. So does function hclge_mdio_write(). Fixes: 1c1249380992 ("net: hns3: bugfix for hclge_mdio_write and hclge_mdio_read") Signed-off-by: Guangbin Huang Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c index 63d2be4349e3..03d63b6a9b2b 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c @@ -48,7 +48,7 @@ static int hclge_mdio_write(struct mii_bus *bus, int phyid, int regnum, int ret; if (test_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state)) - return 0; + return -EBUSY; hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, false); @@ -86,7 +86,7 @@ static int hclge_mdio_read(struct mii_bus *bus, int phyid, int regnum) int ret; if (test_bit(HCLGE_COMM_STATE_CMD_DISABLE, &hdev->hw.hw.comm_state)) - return 0; + return -EBUSY; hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, true); -- cgit From 08be6b13db23f68146c600dd5adfd92e99d9ec6e Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Sat, 26 Mar 2022 11:02:34 -0700 Subject: net: sparx5: depends on PTP_1588_CLOCK_OPTIONAL Fix build errors when PTP_1588_CLOCK=m and SPARX5_SWTICH=y. arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ethtool.o: in function `sparx5_get_ts_info': sparx5_ethtool.c:(.text+0x146): undefined reference to `ptp_clock_index' arc-linux-ld: sparx5_ethtool.c:(.text+0x146): undefined reference to `ptp_clock_index' arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ptp.o: in function `sparx5_ptp_init': sparx5_ptp.c:(.text+0xd56): undefined reference to `ptp_clock_register' arc-linux-ld: sparx5_ptp.c:(.text+0xd56): undefined reference to `ptp_clock_register' arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ptp.o: in function `sparx5_ptp_deinit': sparx5_ptp.c:(.text+0xf30): undefined reference to `ptp_clock_unregister' arc-linux-ld: sparx5_ptp.c:(.text+0xf30): undefined reference to `ptp_clock_unregister' arc-linux-ld: sparx5_ptp.c:(.text+0xf38): undefined reference to `ptp_clock_unregister' arc-linux-ld: sparx5_ptp.c:(.text+0xf46): undefined reference to `ptp_clock_unregister' arc-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_ptp.o:sparx5_ptp.c:(.text+0xf46): more undefined references to `ptp_clock_unregister' follow Fixes: 3cfa11bac9bb ("net: sparx5: add the basic sparx5 driver") Signed-off-by: Randy Dunlap Reported-by: kernel test robot Cc: Horatiu Vultur Cc: UNGLinuxDriver@microchip.com Cc: "David S. Miller" Cc: Jakub Kicinski Cc: Paolo Abeni Cc: Steen Hegelund Cc: Bjarni Jonasson Cc: Lars Povlsen Signed-off-by: David S. Miller --- drivers/net/ethernet/microchip/sparx5/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/microchip/sparx5/Kconfig b/drivers/net/ethernet/microchip/sparx5/Kconfig index 7bdbb2d09a14..85b24edb65d5 100644 --- a/drivers/net/ethernet/microchip/sparx5/Kconfig +++ b/drivers/net/ethernet/microchip/sparx5/Kconfig @@ -4,6 +4,7 @@ config SPARX5_SWITCH depends on HAS_IOMEM depends on OF depends on ARCH_SPARX5 || COMPILE_TEST + depends on PTP_1588_CLOCK_OPTIONAL select PHYLINK select PHY_SPARX5_SERDES select RESET_CONTROLLER -- cgit From 1521db37f0d42334a88e8ff28198a27d1ed5cd7b Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 26 Mar 2022 10:20:03 -0700 Subject: qlcnic: dcb: default to returning -EOPNOTSUPP Clang static analysis reports this issue qlcnic_dcb.c:382:10: warning: Assigned value is garbage or undefined mbx_out = *val; ^ ~~~~ val is set in the qlcnic_dcb_query_hw_capability() wrapper. If there is no query_hw_capability op in dcp, success is returned without setting the val. For this and similar wrappers, return -EOPNOTSUPP. Fixes: 14d385b99059 ("qlcnic: dcb: Query adapter DCB capabilities.") Signed-off-by: Tom Rix Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.h b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.h index 5d79ee4370bc..7519773eaca6 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.h +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.h @@ -51,7 +51,7 @@ static inline int qlcnic_dcb_get_hw_capability(struct qlcnic_dcb *dcb) if (dcb && dcb->ops->get_hw_capability) return dcb->ops->get_hw_capability(dcb); - return 0; + return -EOPNOTSUPP; } static inline void qlcnic_dcb_free(struct qlcnic_dcb *dcb) @@ -65,7 +65,7 @@ static inline int qlcnic_dcb_attach(struct qlcnic_dcb *dcb) if (dcb && dcb->ops->attach) return dcb->ops->attach(dcb); - return 0; + return -EOPNOTSUPP; } static inline int @@ -74,7 +74,7 @@ qlcnic_dcb_query_hw_capability(struct qlcnic_dcb *dcb, char *buf) if (dcb && dcb->ops->query_hw_capability) return dcb->ops->query_hw_capability(dcb, buf); - return 0; + return -EOPNOTSUPP; } static inline void qlcnic_dcb_get_info(struct qlcnic_dcb *dcb) @@ -89,7 +89,7 @@ qlcnic_dcb_query_cee_param(struct qlcnic_dcb *dcb, char *buf, u8 type) if (dcb && dcb->ops->query_cee_param) return dcb->ops->query_cee_param(dcb, buf, type); - return 0; + return -EOPNOTSUPP; } static inline int qlcnic_dcb_get_cee_cfg(struct qlcnic_dcb *dcb) @@ -97,7 +97,7 @@ static inline int qlcnic_dcb_get_cee_cfg(struct qlcnic_dcb *dcb) if (dcb && dcb->ops->get_cee_cfg) return dcb->ops->get_cee_cfg(dcb); - return 0; + return -EOPNOTSUPP; } static inline void qlcnic_dcb_aen_handler(struct qlcnic_dcb *dcb, void *msg) -- cgit From 0906f3a3df07835e37077d8971aac65347f2ed57 Mon Sep 17 00:00:00 2001 From: Zheng Yongjun Date: Sat, 26 Mar 2022 08:12:39 +0000 Subject: net: sparx5: switchdev: fix possible NULL pointer dereference As the possible failure of the allocation, devm_kzalloc() may return NULL pointer. Therefore, it should be better to check the 'db' in order to prevent the dereference of NULL pointer. Fixes: 10615907e9b51 ("net: sparx5: switchdev: adding frame DMA functionality") Signed-off-by: Zheng Yongjun Signed-off-by: David S. Miller --- drivers/net/ethernet/microchip/sparx5/sparx5_fdma.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_fdma.c b/drivers/net/ethernet/microchip/sparx5/sparx5_fdma.c index 2dc87584023a..1e9ff365459e 100644 --- a/drivers/net/ethernet/microchip/sparx5/sparx5_fdma.c +++ b/drivers/net/ethernet/microchip/sparx5/sparx5_fdma.c @@ -422,6 +422,8 @@ static int sparx5_fdma_tx_alloc(struct sparx5 *sparx5) db_hw->dataptr = phys; db_hw->status = 0; db = devm_kzalloc(sparx5->dev, sizeof(*db), GFP_KERNEL); + if (!db) + return -ENOMEM; db->cpu_addr = cpu_addr; list_add_tail(&db->list, &tx->db_list); } -- cgit From 33b5bc9e703383e396f275d51fc4bafa48dbae5a Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 26 Mar 2022 09:03:06 -0700 Subject: octeontx2-af: initialize action variable Clang static analysis reports this representative issue rvu_npc.c:898:15: warning: Assigned value is garbage or undefined req.match_id = action.match_id; ^ ~~~~~~~~~~~~~~~ The initial setting of action is conditional on if (is_mcam_entry_enabled(...)) The later check of action.op will sometimes be garbage. So initialize action. Reduce setting of *(u64 *)&action = 0x00; to *(u64 *)&action = 0; Fixes: 967db3529eca ("octeontx2-af: add support for multicast/promisc packet replication feature") Signed-off-by: Tom Rix Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c | 15 +++++++-------- 1 file changed, 7 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c b/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c index 91f86d77cd41..3a31fb8cc155 100644 --- a/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c +++ b/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c @@ -605,7 +605,7 @@ void rvu_npc_install_ucast_entry(struct rvu *rvu, u16 pcifunc, struct npc_install_flow_req req = { 0 }; struct npc_install_flow_rsp rsp = { 0 }; struct npc_mcam *mcam = &rvu->hw->mcam; - struct nix_rx_action action; + struct nix_rx_action action = { 0 }; int blkaddr, index; /* AF's and SDP VFs work in promiscuous mode */ @@ -626,7 +626,6 @@ void rvu_npc_install_ucast_entry(struct rvu *rvu, u16 pcifunc, *(u64 *)&action = npc_get_mcam_action(rvu, mcam, blkaddr, index); } else { - *(u64 *)&action = 0x00; action.op = NIX_RX_ACTIONOP_UCAST; action.pf_func = pcifunc; } @@ -657,7 +656,7 @@ void rvu_npc_install_promisc_entry(struct rvu *rvu, u16 pcifunc, struct npc_mcam *mcam = &rvu->hw->mcam; struct rvu_hwinfo *hw = rvu->hw; int blkaddr, ucast_idx, index; - struct nix_rx_action action; + struct nix_rx_action action = { 0 }; u64 relaxed_mask; if (!hw->cap.nix_rx_multicast && is_cgx_vf(rvu, pcifunc)) @@ -685,14 +684,14 @@ void rvu_npc_install_promisc_entry(struct rvu *rvu, u16 pcifunc, blkaddr, ucast_idx); if (action.op != NIX_RX_ACTIONOP_RSS) { - *(u64 *)&action = 0x00; + *(u64 *)&action = 0; action.op = NIX_RX_ACTIONOP_UCAST; } /* RX_ACTION set to MCAST for CGX PF's */ if (hw->cap.nix_rx_multicast && pfvf->use_mce_list && is_pf_cgxmapped(rvu, rvu_get_pf(pcifunc))) { - *(u64 *)&action = 0x00; + *(u64 *)&action = 0; action.op = NIX_RX_ACTIONOP_MCAST; pfvf = rvu_get_pfvf(rvu, pcifunc & ~RVU_PFVF_FUNC_MASK); action.index = pfvf->promisc_mce_idx; @@ -832,7 +831,7 @@ void rvu_npc_install_allmulti_entry(struct rvu *rvu, u16 pcifunc, int nixlf, struct rvu_hwinfo *hw = rvu->hw; int blkaddr, ucast_idx, index; u8 mac_addr[ETH_ALEN] = { 0 }; - struct nix_rx_action action; + struct nix_rx_action action = { 0 }; struct rvu_pfvf *pfvf; u16 vf_func; @@ -861,14 +860,14 @@ void rvu_npc_install_allmulti_entry(struct rvu *rvu, u16 pcifunc, int nixlf, blkaddr, ucast_idx); if (action.op != NIX_RX_ACTIONOP_RSS) { - *(u64 *)&action = 0x00; + *(u64 *)&action = 0; action.op = NIX_RX_ACTIONOP_UCAST; action.pf_func = pcifunc; } /* RX_ACTION set to MCAST for CGX PF's */ if (hw->cap.nix_rx_multicast && pfvf->use_mce_list) { - *(u64 *)&action = 0x00; + *(u64 *)&action = 0; action.op = NIX_RX_ACTIONOP_MCAST; action.index = pfvf->mcast_mce_idx; } -- cgit From dcf500065fabe27676dfe7b4ba521a4f1e0fc8ac Mon Sep 17 00:00:00 2001 From: Damien Le Moal Date: Mon, 28 Mar 2022 15:27:08 +0900 Subject: net: bnxt_ptp: fix compilation error MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The Broadcom bnxt_ptp driver does not compile with GCC 11.2.2 when CONFIG_WERROR is enabled. The following error is generated: drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c: In function ‘bnxt_ptp_enable’: drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:400:43: error: array subscript 255 is above array bounds of ‘struct pps_pin[4]’ [-Werror=array-bounds] 400 | ptp->pps_info.pins[pin_id].event = BNXT_PPS_EVENT_EXTERNAL; | ~~~~~~~~~~~~~~~~~~^~~~~~~~ In file included from drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:20: drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h:75:24: note: while referencing ‘pins’ 75 | struct pps_pin pins[BNXT_MAX_TSIO_PINS]; | ^~~~ cc1: all warnings being treated as errors This is due to the function ptp_find_pin() returning a pin ID of -1 when a valid pin is not found and this error never being checked. Change the TSIO_PIN_VALID() function to also check that a pin ID is not negative and use this macro in bnxt_ptp_enable() to check the result of the calls to ptp_find_pin() to return an error early for invalid pins. This fixes the compilation error. Cc: Fixes: 9e518f25802c ("bnxt_en: 1PPS functions to configure TSIO pins") Signed-off-by: Damien Le Moal Reviewed-by: Michael Chan Link: https://lore.kernel.org/r/20220328062708.207079-1-damien.lemoal@opensource.wdc.com Signed-off-by: Jakub Kicinski --- drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c | 6 +++++- drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h | 2 +- 2 files changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c b/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c index a0b321a19361..9c2ad5e67a5d 100644 --- a/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c +++ b/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c @@ -382,7 +382,7 @@ static int bnxt_ptp_enable(struct ptp_clock_info *ptp_info, struct bnxt_ptp_cfg *ptp = container_of(ptp_info, struct bnxt_ptp_cfg, ptp_info); struct bnxt *bp = ptp->bp; - u8 pin_id; + int pin_id; int rc; switch (rq->type) { @@ -390,6 +390,8 @@ static int bnxt_ptp_enable(struct ptp_clock_info *ptp_info, /* Configure an External PPS IN */ pin_id = ptp_find_pin(ptp->ptp_clock, PTP_PF_EXTTS, rq->extts.index); + if (!TSIO_PIN_VALID(pin_id)) + return -EOPNOTSUPP; if (!on) break; rc = bnxt_ptp_cfg_pin(bp, pin_id, BNXT_PPS_PIN_PPS_IN); @@ -403,6 +405,8 @@ static int bnxt_ptp_enable(struct ptp_clock_info *ptp_info, /* Configure a Periodic PPS OUT */ pin_id = ptp_find_pin(ptp->ptp_clock, PTP_PF_PEROUT, rq->perout.index); + if (!TSIO_PIN_VALID(pin_id)) + return -EOPNOTSUPP; if (!on) break; diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h b/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h index 373baf45884b..530b9922608c 100644 --- a/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h +++ b/drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h @@ -31,7 +31,7 @@ struct pps_pin { u8 state; }; -#define TSIO_PIN_VALID(pin) ((pin) < (BNXT_MAX_TSIO_PINS)) +#define TSIO_PIN_VALID(pin) ((pin) >= 0 && (pin) < (BNXT_MAX_TSIO_PINS)) #define EVENT_DATA2_PPS_EVENT_TYPE(data2) \ ((data2) & ASYNC_EVENT_CMPL_PPS_TIMESTAMP_EVENT_DATA2_EVENT_TYPE) -- cgit From 6da69b1da130e7d96766042750cd9f902e890eba Mon Sep 17 00:00:00 2001 From: Xiaomeng Tong Date: Mon, 28 Mar 2022 11:24:31 +0800 Subject: net: dsa: bcm_sf2_cfp: fix an incorrect NULL check on list iterator The bug is here: return rule; The list iterator value 'rule' will *always* be set and non-NULL by list_for_each_entry(), so it is incorrect to assume that the iterator value will be NULL if the list is empty or no element is found. To fix the bug, return 'rule' when found, otherwise return NULL. Fixes: ae7a5aff783c7 ("net: dsa: bcm_sf2: Keep copy of inserted rules") Reviewed-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: Xiaomeng Tong Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com Signed-off-by: Jakub Kicinski --- drivers/net/dsa/bcm_sf2_cfp.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/dsa/bcm_sf2_cfp.c b/drivers/net/dsa/bcm_sf2_cfp.c index a7e2fcf2df2c..edbe5e7f1cb6 100644 --- a/drivers/net/dsa/bcm_sf2_cfp.c +++ b/drivers/net/dsa/bcm_sf2_cfp.c @@ -567,14 +567,14 @@ static void bcm_sf2_cfp_slice_ipv6(struct bcm_sf2_priv *priv, static struct cfp_rule *bcm_sf2_cfp_rule_find(struct bcm_sf2_priv *priv, int port, u32 location) { - struct cfp_rule *rule = NULL; + struct cfp_rule *rule; list_for_each_entry(rule, &priv->cfp.rules_list, next) { if (rule->port == port && rule->fs.location == location) - break; + return rule; } - return rule; + return NULL; } static int bcm_sf2_cfp_rule_cmp(struct bcm_sf2_priv *priv, int port, -- cgit