.. SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB .. include:: ======= Devlink ======= :Copyright: |copy| 2023, NVIDIA CORPORATION & AFFILIATES. All rights reserved. Contents ======== - `Info`_ - `Parameters`_ - `Health reporters`_ Info ==== The devlink info reports the running and stored firmware versions on device. It also prints the device PSID which represents the HCA board type ID. User command example:: $ devlink dev info pci/0000:00:06.0 pci/0000:00:06.0: driver mlx5_core versions: fixed: fw.psid MT_0000000009 running: fw.version 16.26.0100 stored: fw.version 16.26.0100 Parameters ========== flow_steering_mode: Device flow steering mode --------------------------------------------- The flow steering mode parameter controls the flow steering mode of the driver. Two modes are supported: 1. 'dmfs' - Device managed flow steering. 2. 'smfs' - Software/Driver managed flow steering. In DMFS mode, the HW steering entities are created and managed through the Firmware. In SMFS mode, the HW steering entities are created and managed though by the driver directly into hardware without firmware intervention. SMFS mode is faster and provides better rule insertion rate compared to default DMFS mode. User command examples: - Set SMFS flow steering mode:: $ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime - Read device flow steering mode:: $ devlink dev param show pci/0000:06:00.0 name flow_steering_mode pci/0000:06:00.0: name flow_steering_mode type driver-specific values: cmode runtime value smfs enable_roce: RoCE enablement state ---------------------------------- If the device supports RoCE disablement, RoCE enablement state controls device support for RoCE capability. Otherwise, the control occurs in the driver stack. When RoCE is disabled at the driver level, only raw ethernet QPs are supported. To change RoCE enablement state, a user must change the driverinit cmode value and run devlink reload. User command examples: - Disable RoCE:: $ devlink dev param set pci/0000:06:00.0 name enable_roce value false cmode driverinit $ devlink dev reload pci/0000:06:00.0 - Read RoCE enablement state:: $ devlink dev param show pci/0000:06:00.0 name enable_roce pci/0000:06:00.0: name enable_roce type generic values: cmode driverinit value true esw_port_metadata: Eswitch port metadata state ---------------------------------------------- When applicable, disabling eswitch metadata can increase packet rate up to 20% depending on the use case and packet sizes. Eswitch port metadata state controls whether to internally tag packets with metadata. Metadata tagging must be enabled for multi-port RoCE, failover between representors and stacked devices. By default metadata is enabled on the supported devices in E-switch. Metadata is applicable only for E-switch in switchdev mode and users may disable it when NONE of the below use cases will be in use: 1. HCA is in Dual/multi-port RoCE mode. 2. VF/SF representor bonding (Usually used for Live migration) 3. Stacked devices When metadata is disabled, the above use cases will fail to initialize if users try to enable them. - Show eswitch port metadata:: $ devlink dev param show pci/0000:06:00.0 name esw_port_metadata pci/0000:06:00.0: name esw_port_metadata type driver-specific values: cmode runtime value true - Disable eswitch port metadata:: $ devlink dev param set pci/0000:06:00.0 name esw_port_metadata value false cmode runtime - Change eswitch mode to switchdev mode where after choosing the metadata value:: $ devlink dev eswitch set pci/0000:06:00.0 mode switchdev Health reporters ================ tx reporter ----------- The tx reporter is responsible for reporting and recovering of the following two error scenarios: - tx timeout Report on kernel tx timeout detection. Recover by searching lost interrupts. - tx error completion Report on error tx completion. Recover by flushing the tx queue and reset it. tx reporter also support on demand diagnose callback, on which it provides real time information of its send queues status. User commands examples: - Diagnose send queues status:: $ devlink health diagnose pci/0000:82:00.0 reporter tx NOTE: This command has valid output only when interface is up, otherwise the command has empty output. - Show number of tx errors indicated, number of recover flows ended successfully, is autorecover enabled and graceful period from last recover:: $ devlink health show pci/0000:82:00.0 reporter tx rx reporter ----------- The rx reporter is responsible for reporting and recovering of the following two error scenarios: - rx queues' initialization (population) timeout Population of rx queues' descriptors on ring initialization is done in napi context via triggering an irq. In case of a failure to get the minimum amount of descriptors, a timeout would occur, and descriptors could be recovered by polling the EQ (Event Queue). - rx completions with errors (reported by HW on interrupt context) Report on rx completion error. Recover (if needed) by flushing the related queue and reset it. rx reporter also supports on demand diagnose callback, on which it provides real time information of its receive queues' status. - Diagnose rx queues' status and corresponding completion queue:: $ devlink health diagnose pci/0000:82:00.0 reporter rx NOTE: This command has valid output only when interface is up. Otherwise, the command has empty output. - Show number of rx errors indicated, number of recover flows ended successfully, is autorecover enabled, and graceful period from last recover:: $ devlink health show pci/0000:82:00.0 reporter rx fw reporter ----------- The fw reporter implements `diagnose` and `dump` callbacks. It follows symptoms of fw error such as fw syndrome by triggering fw core dump and storing it into the dump buffer. The fw reporter diagnose command can be triggered any time by the user to check current fw status. User commands examples: - Check fw heath status:: $ devlink health diagnose pci/0000:82:00.0 reporter fw - Read FW core dump if already stored or trigger new one:: $ devlink health dump show pci/0000:82:00.0 reporter fw NOTE: This command can run only on the PF which has fw tracer ownership, running it on other PF or any VF will return "Operation not permitted". fw fatal reporter ----------------- The fw fatal reporter implements `dump` and `recover` callbacks. It follows fatal errors indications by CR-space dump and recover flow. The CR-space dump uses vsc interface which is valid even if the FW command interface is not functional, which is the case in most FW fatal errors. The recover function runs recover flow which reloads the driver and triggers fw reset if needed. On firmware error, the health buffer is dumped into the dmesg. The log level is derived from the error's severity (given in health buffer). User commands examples: - Run fw recover flow manually:: $ devlink health recover pci/0000:82:00.0 reporter fw_fatal - Read FW CR-space dump if already stored or trigger new one:: $ devlink health dump show pci/0000:82:00.1 reporter fw_fatal NOTE: This command can run only on PF.