/* * arch/arm/mach-ep93xx/simone.c * Simplemachines Sim.One support. * * Copyright (C) 2010 Ryan Mallon * * Based on the 2.6.24.7 support: * Copyright (C) 2009 Simplemachines * MMC support by Peter Ivanov , 2007 * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or (at * your option) any later version. * */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "soc.h" static struct ep93xx_eth_data __initdata simone_eth_data = { .phy_id = 1, }; static struct ep93xxfb_mach_info __initdata simone_fb_info = { .flags = EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING, }; /* * GPIO lines used for MMC card detection. */ #define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0 /* * MMC card detection GPIO setup. */ static int simone_mmc_spi_init(struct device *dev, irqreturn_t (*irq_handler)(int, void *), void *mmc) { unsigned int gpio = MMC_CARD_DETECT_GPIO; int irq, err; err = gpio_request(gpio, dev_name(dev)); if (err) return err; err = gpio_direction_input(gpio); if (err) goto fail; irq = gpio_to_irq(gpio); if (irq < 0) goto fail; err = request_irq(irq, irq_handler, IRQF_TRIGGER_FALLING, "MMC card detect", mmc); if (err) goto fail; printk(KERN_INFO "%s: using irq %d for MMC card detection\n", dev_name(dev), irq); return 0; fail: gpio_free(gpio); return err; } static void simone_mmc_spi_exit(struct device *dev, void *mmc) { unsigned int gpio = MMC_CARD_DETECT_GPIO; free_irq(gpio_to_irq(gpio), mmc); gpio_free(gpio); } static struct mmc_spi_platform_data simone_mmc_spi_data = { .init = simone_mmc_spi_init, .exit = simone_mmc_spi_exit, .detect_delay = 500, .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, }; static struct spi_board_info simone_spi_devices[] __initdata = { { .modalias = "mmc_spi", .platform_data = &simone_mmc_spi_data, /* * We use 10 MHz even though the maximum is 3.7 MHz. The driver * will limit it automatically to max. frequency. */ .max_speed_hz = 10 * 1000 * 1000, .bus_num = 0, .chip_select = 0, .mode = SPI_MODE_3, }, }; /* * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes * low between multi-message command blocks. From v1.4, it uses a GPIO instead. * v1.3 parts will still work, since the signal on SFRMOUT is automatic. */ static int simone_spi_chipselects[] __initdata = { EP93XX_GPIO_LINE_EGPIO1, }; static struct ep93xx_spi_info simone_spi_info __initdata = { .chipselect = simone_spi_chipselects, .num_chipselect = ARRAY_SIZE(simone_spi_chipselects), .use_dma = 1, }; static struct i2c_board_info __initdata simone_i2c_board_info[] = { { I2C_BOARD_INFO("ds1337", 0x68), }, }; static struct platform_device simone_audio_device = { .name = "simone-audio", .id = -1, }; static void __init simone_register_audio(void) { ep93xx_register_ac97(); platform_device_register(&simone_audio_device); } static void __init simone_init_machine(void) { ep93xx_init_devices(); ep93xx_register_flash(2, EP93XX_CS6_PHYS_BASE, SZ_8M); ep93xx_register_eth(&simone_eth_data, 1); ep93xx_register_fb(&simone_fb_info); ep93xx_register_i2c(simone_i2c_board_info, ARRAY_SIZE(simone_i2c_board_info)); ep93xx_register_spi(&simone_spi_info, simone_spi_devices, ARRAY_SIZE(simone_spi_devices)); simone_register_audio(); } MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board") /* Maintainer: Ryan Mallon */ .atag_offset = 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, .init_time = ep93xx_timer_init, .init_machine = simone_init_machine, .init_late = ep93xx_init_late, .restart = ep93xx_restart, MACHINE_END