summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
blob: 593be44a53c9527774c35ca9331f9b25e23d97cd (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
NVIDIA Tegra host1x

Required properties:
- compatible: "nvidia,tegra<chip>-host1x"
- reg: Physical base address and length of the controller's registers.
  For pre-Tegra186, one entry describing the whole register area.
  For Tegra186, one entry for each entry in reg-names:
    "vm" - VM region assigned to Linux
    "hypervisor" - Hypervisor region (only if Linux acts as hypervisor)
- interrupts: The interrupt outputs from the controller.
- #address-cells: The number of cells used to represent physical base addresses
  in the host1x address space. Should be 1.
- #size-cells: The number of cells used to represent the size of an address
  range in the host1x address space. Should be 1.
- ranges: The mapping of the host1x address space to the CPU address space.
- clocks: Must contain one entry, for the module clock.
  See ../clocks/clock-bindings.txt for details.
- resets: Must contain an entry for each entry in reset-names.
  See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
  - host1x

The host1x top-level node defines a number of children, each representing one
of the following host1x client modules:

- mpe: video encoder

  Required properties:
  - compatible: "nvidia,tegra<chip>-mpe"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain one entry, for the module clock.
    See ../clocks/clock-bindings.txt for details.
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - mpe

- vi: video input

  Required properties:
  - compatible: "nvidia,tegra<chip>-vi"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain one entry, for the module clock.
    See ../clocks/clock-bindings.txt for details.
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - vi

- epp: encoder pre-processor

  Required properties:
  - compatible: "nvidia,tegra<chip>-epp"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain one entry, for the module clock.
    See ../clocks/clock-bindings.txt for details.
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - epp

- isp: image signal processor

  Required properties:
  - compatible: "nvidia,tegra<chip>-isp"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain one entry, for the module clock.
    See ../clocks/clock-bindings.txt for details.
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - isp

- gr2d: 2D graphics engine

  Required properties:
  - compatible: "nvidia,tegra<chip>-gr2d"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain one entry, for the module clock.
    See ../clocks/clock-bindings.txt for details.
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - 2d

- gr3d: 3D graphics engine

  Required properties:
  - compatible: "nvidia,tegra<chip>-gr3d"
  - reg: Physical base address and length of the controller's registers.
  - clocks: Must contain an entry for each entry in clock-names.
    See ../clocks/clock-bindings.txt for details.
  - clock-names: Must include the following entries:
    (This property may be omitted if the only clock in the list is "3d")
    - 3d
      This MUST be the first entry.
    - 3d2 (Only required on SoCs with two 3D clocks)
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - 3d
    - 3d2 (Only required on SoCs with two 3D clocks)

- dc: display controller

  Required properties:
  - compatible: "nvidia,tegra<chip>-dc"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain an entry for each entry in clock-names.
    See ../clocks/clock-bindings.txt for details.
  - clock-names: Must include the following entries:
    - dc
      This MUST be the first entry.
    - parent
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - dc
  - nvidia,head: The number of the display controller head. This is used to
    setup the various types of output to receive video data from the given
    head.

  Each display controller node has a child node, named "rgb", that represents
  the RGB output associated with the controller. It can take the following
  optional properties:
  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
  - nvidia,edid: supplies a binary EDID blob
  - nvidia,panel: phandle of a display panel

- hdmi: High Definition Multimedia Interface

  Required properties:
  - compatible: "nvidia,tegra<chip>-hdmi"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - hdmi-supply: supply for the +5V HDMI connector pin
  - vdd-supply: regulator for supply voltage
  - pll-supply: regulator for PLL
  - clocks: Must contain an entry for each entry in clock-names.
    See ../clocks/clock-bindings.txt for details.
  - clock-names: Must include the following entries:
    - hdmi
      This MUST be the first entry.
    - parent
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - hdmi

  Optional properties:
  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
  - nvidia,edid: supplies a binary EDID blob
  - nvidia,panel: phandle of a display panel

- tvo: TV encoder output

  Required properties:
  - compatible: "nvidia,tegra<chip>-tvo"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain one entry, for the module clock.
    See ../clocks/clock-bindings.txt for details.

- dsi: display serial interface

  Required properties:
  - compatible: "nvidia,tegra<chip>-dsi"
  - reg: Physical base address and length of the controller's registers.
  - clocks: Must contain an entry for each entry in clock-names.
    See ../clocks/clock-bindings.txt for details.
  - clock-names: Must include the following entries:
    - dsi
      This MUST be the first entry.
    - lp
    - parent
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - dsi
  - avdd-dsi-supply: phandle of a supply that powers the DSI controller
  - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying
    which pads are used by this DSI output and need to be calibrated. See also
    ../display/tegra/nvidia,tegra114-mipi.txt.

  Optional properties:
  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
  - nvidia,edid: supplies a binary EDID blob
  - nvidia,panel: phandle of a display panel
  - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang
    up with in order to support up to 8 data lanes

- sor: serial output resource

  Required properties:
  - compatible: Should be:
    - "nvidia,tegra124-sor": for Tegra124 and Tegra132
    - "nvidia,tegra132-sor": for Tegra132
    - "nvidia,tegra210-sor": for Tegra210
    - "nvidia,tegra210-sor1": for Tegra210
    - "nvidia,tegra186-sor": for Tegra186
    - "nvidia,tegra186-sor1": for Tegra186
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain an entry for each entry in clock-names.
    See ../clocks/clock-bindings.txt for details.
  - clock-names: Must include the following entries:
    - sor: clock input for the SOR hardware
    - out: SOR output clock
    - parent: input for the pixel clock
    - dp: reference clock for the SOR clock
    - safe: safe reference for the SOR clock during power up

    For Tegra186 and later:
    - pad: SOR pad output clock (on Tegra186 and later)

    Obsolete:
    - source: source clock for the SOR clock (obsolete, use "out" instead)

  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - sor

  Required properties on Tegra186 and later:
  - nvidia,interface: index of the SOR interface

  Optional properties:
  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
  - nvidia,edid: supplies a binary EDID blob
  - nvidia,panel: phandle of a display panel

  Optional properties when driving an eDP output:
  - nvidia,dpaux: phandle to a DispayPort AUX interface

- dpaux: DisplayPort AUX interface
  - compatible : Should contain one of the following:
    - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132
    - "nvidia,tegra210-dpaux": for Tegra210
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain an entry for each entry in clock-names.
    See ../clocks/clock-bindings.txt for details.
  - clock-names: Must include the following entries:
    - dpaux: clock input for the DPAUX hardware
    - parent: reference clock
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - dpaux
  - vdd-supply: phandle of a supply that powers the DisplayPort link
  - i2c-bus: Subnode where I2C slave devices are listed. This subnode
    must be always present. If there are no I2C slave devices, an empty
    node should be added. See ../../i2c/i2c.txt for more information.

  See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information
  regarding the DPAUX pad controller bindings.

- vic: Video Image Compositor
  - compatible : "nvidia,tegra<chip>-vic"
  - reg: Physical base address and length of the controller's registers.
  - interrupts: The interrupt outputs from the controller.
  - clocks: Must contain an entry for each entry in clock-names.
    See ../clocks/clock-bindings.txt for details.
  - clock-names: Must include the following entries:
    - vic: clock input for the VIC hardware
  - resets: Must contain an entry for each entry in reset-names.
    See ../reset/reset.txt for details.
  - reset-names: Must include the following entries:
    - vic

Example:

/ {
	...

	host1x {
		compatible = "nvidia,tegra20-host1x", "simple-bus";
		reg = <0x50000000 0x00024000>;
		interrupts = <0 65 0x04   /* mpcore syncpt */
			      0 67 0x04>; /* mpcore general */
		clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
		resets = <&tegra_car 28>;
		reset-names = "host1x";

		#address-cells = <1>;
		#size-cells = <1>;

		ranges = <0x54000000 0x54000000 0x04000000>;

		mpe {
			compatible = "nvidia,tegra20-mpe";
			reg = <0x54040000 0x00040000>;
			interrupts = <0 68 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_MPE>;
			resets = <&tegra_car 60>;
			reset-names = "mpe";
		};

		vi {
			compatible = "nvidia,tegra20-vi";
			reg = <0x54080000 0x00040000>;
			interrupts = <0 69 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_VI>;
			resets = <&tegra_car 100>;
			reset-names = "vi";
		};

		epp {
			compatible = "nvidia,tegra20-epp";
			reg = <0x540c0000 0x00040000>;
			interrupts = <0 70 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_EPP>;
			resets = <&tegra_car 19>;
			reset-names = "epp";
		};

		isp {
			compatible = "nvidia,tegra20-isp";
			reg = <0x54100000 0x00040000>;
			interrupts = <0 71 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_ISP>;
			resets = <&tegra_car 23>;
			reset-names = "isp";
		};

		gr2d {
			compatible = "nvidia,tegra20-gr2d";
			reg = <0x54140000 0x00040000>;
			interrupts = <0 72 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_GR2D>;
			resets = <&tegra_car 21>;
			reset-names = "2d";
		};

		gr3d {
			compatible = "nvidia,tegra20-gr3d";
			reg = <0x54180000 0x00040000>;
			clocks = <&tegra_car TEGRA20_CLK_GR3D>;
			resets = <&tegra_car 24>;
			reset-names = "3d";
		};

		dc@54200000 {
			compatible = "nvidia,tegra20-dc";
			reg = <0x54200000 0x00040000>;
			interrupts = <0 73 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_DISP1>,
				 <&tegra_car TEGRA20_CLK_PLL_P>;
			clock-names = "dc", "parent";
			resets = <&tegra_car 27>;
			reset-names = "dc";

			rgb {
				status = "disabled";
			};
		};

		dc@54240000 {
			compatible = "nvidia,tegra20-dc";
			reg = <0x54240000 0x00040000>;
			interrupts = <0 74 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_DISP2>,
				 <&tegra_car TEGRA20_CLK_PLL_P>;
			clock-names = "dc", "parent";
			resets = <&tegra_car 26>;
			reset-names = "dc";

			rgb {
				status = "disabled";
			};
		};

		hdmi {
			compatible = "nvidia,tegra20-hdmi";
			reg = <0x54280000 0x00040000>;
			interrupts = <0 75 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_HDMI>,
				 <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
			clock-names = "hdmi", "parent";
			resets = <&tegra_car 51>;
			reset-names = "hdmi";
			status = "disabled";
		};

		tvo {
			compatible = "nvidia,tegra20-tvo";
			reg = <0x542c0000 0x00040000>;
			interrupts = <0 76 0x04>;
			clocks = <&tegra_car TEGRA20_CLK_TVO>;
			status = "disabled";
		};

		dsi {
			compatible = "nvidia,tegra20-dsi";
			reg = <0x54300000 0x00040000>;
			clocks = <&tegra_car TEGRA20_CLK_DSI>,
				 <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
			clock-names = "dsi", "parent";
			resets = <&tegra_car 48>;
			reset-names = "dsi";
			status = "disabled";
		};
	};

	...
};