summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/hwmon/ntc-thermistor.yaml
blob: 3d3b139a91a2f95a422bb45c546a39cc5681da2c (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
---
$id: http://devicetree.org/schemas/hwmon/ntc-thermistor.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: NTC thermistor temperature sensors

maintainers:
  - Naveen Krishna Chatradhi <ch.naveen@samsung.com>
  - Linus Walleij <linus.walleij@linaro.org>

description: |
  Thermistors with negative temperature coefficient (NTC) are resistors that
  vary in resistance in an often non-linear way in relation to temperature.
  The negative temperature coefficient means that the resistance decreases
  as the temperature rises. Since the relationship between resistance and
  temperature is non-linear, software drivers most often need to use a look
  up table and interpolation to get from resistance to temperature.

  When used in practice, a thermistor is often connected between ground, a
  pull-up resistor or/and a pull-down resistor and a fixed voltage like this:

      + e.g. 5V = pull-up voltage (puv)
      |
     +-+
     | |
     | | Pull-up resistor
     | | (puo)
     +-+
      |-------------------------o
     +-+ |                      ^
     | |/                       |
     | /                        |
     |/| Thermistor             | Measured voltage (mv)
     / |                        | "connected ground"
    /| |                        |
     +-+                        |
      |-------------------------o
     +-+                        ^
     | |                        |
     | | Pull-down resistor     | Measured voltage (mv)
     | | (pdo)                  | "connected positive"
     +-+                        |
      |                         |
      |                         v
      + GND                     GND

  The arrangements of where we measure the voltage over the thermistor are
  called "connected ground" and "connected positive" and shall be understood as
  the cases when either pull-up or pull-down resistance is zero.

  If the pull-up resistance is 0 one end of the thermistor is connected to the
  positive voltage and we get the thermistor on top of a pull-down resistor
  and we take the measure between the thermistor and the pull-down resistor.

  Conversely if the pull-down resistance is zero, one end of the thermistor is
  connected to ground and we get the thermistor under the pull-up resistor
  and we take the measure between the pull-up resistor and the thermistor.

  We can use both pull-up and pull-down resistors at the same time, and then
  the figure illustrates where the voltage will be measured for the "connected
  ground" and "connected positive" cases.

properties:
  $nodename:
    pattern: "^thermistor(.*)?$"

  compatible:
    oneOf:
      - const: epcos,b57330v2103
      - const: epcos,b57891s0103
      - const: murata,ncp15wb473
      - const: murata,ncp18wb473
      - const: murata,ncp21wb473
      - const: murata,ncp03wb473
      - const: murata,ncp15wl333
      - const: murata,ncp03wf104
      - const: murata,ncp15xh103
      - const: samsung,1404-001221
      # Deprecated "ntp," compatible strings
      - const: ntc,ncp15wb473
        deprecated: true
      - const: ntc,ncp18wb473
        deprecated: true
      - const: ntc,ncp21wb473
        deprecated: true
      - const: ntc,ncp03wb473
        deprecated: true
      - const: ntc,ncp15wl333
        deprecated: true

  "#thermal-sensor-cells":
    description: Thermal sensor cells if used for thermal sensoring.
    const: 0

  pullup-uv:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: Pull-up voltage in micro volts. Must always be specified.

  pullup-ohm:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: Pull-up resistance in ohms. Must always be specified, even
      if zero.

  pulldown-ohm:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: Pull-down resistance in ohms. Must always be specified, even
      if zero.

  connected-positive:
    $ref: /schemas/types.yaml#/definitions/flag
    description: Indicates how the thermistor is connected in series with
      a pull-up and/or a pull-down resistor. See the description above for
      an illustration. If this flag is NOT specified, the thermistor is assumed
      to be connected-ground, which usually means a pull-down resistance of
      zero but complex arrangements are possible.

  # See /schemas/iio/adc/adc.yaml
  io-channels:
    maxItems: 1
    description: IIO ADC channel to read the voltage over the resistor. Must
      always be specified.

required:
  - compatible
  - pullup-uv
  - pullup-ohm
  - pulldown-ohm
  - io-channels

additionalProperties: false

examples:
  - |
    thermistor0 {
      compatible = "murata,ncp18wb473";
      io-channels = <&gpadc 0x06>;
      pullup-uv = <1800000>;
      pullup-ohm = <220000>;
      pulldown-ohm = <0>;
      #thermal-sensor-cells = <0>;
    };