summaryrefslogtreecommitdiff
path: root/Documentation/driver-api/usb/error-codes.rst
blob: 8f9790c2d6f8f7c3d54bf686ac892ebbaf80766a (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
.. _usb-error-codes:

USB Error codes
~~~~~~~~~~~~~~~

:Revised: 2004-Oct-21

This is the documentation of (hopefully) all possible error codes (and
their interpretation) that can be returned from usbcore.

Some of them are returned by the Host Controller Drivers (HCDs), which
device drivers only see through usbcore.  As a rule, all the HCDs should
behave the same except for transfer speed dependent behaviors and the
way certain faults are reported.


Error codes returned by :c:func:`usb_submit_urb`
================================================

Non-USB-specific:


=============== ===============================================
0		URB submission went fine

``-ENOMEM``	no memory for allocation of internal structures
=============== ===============================================

USB-specific:

=======================	=======================================================
``-EBUSY``		The URB is already active.

``-ENODEV``		specified USB-device or bus doesn't exist

``-ENOENT``		specified interface or endpoint does not exist or
			is not enabled

``-ENXIO``		host controller driver does not support queuing of
			this type of urb.  (treat as a host controller bug.)

``-EINVAL``		a) Invalid transfer type specified (or not supported)
			b) Invalid or unsupported periodic transfer interval
			c) ISO: attempted to change transfer interval
			d) ISO: ``number_of_packets`` is < 0
			e) various other cases

``-EXDEV``		ISO: ``URB_ISO_ASAP`` wasn't specified and all the
			frames the URB would be scheduled in have already
			expired.

``-EFBIG``		Host controller driver can't schedule that many ISO
			frames.

``-EPIPE``		The pipe type specified in the URB doesn't match the
			endpoint's actual type.

``-EMSGSIZE``		(a) endpoint maxpacket size is zero; it is not usable
			    in the current interface altsetting.
			(b) ISO packet is larger than the endpoint maxpacket.
			(c) requested data transfer length is invalid: negative
			    or too large for the host controller.

``-EBADR``		The wLength value in a control URB's setup packet does
			not match the URB's transfer_buffer_length.

``-ENOSPC``		This request would overcommit the usb bandwidth reserved
			for periodic transfers (interrupt, isochronous).

``-ESHUTDOWN``		The device or host controller has been disabled due to
			some problem that could not be worked around.

``-EPERM``		Submission failed because ``urb->reject`` was set.

``-EHOSTUNREACH``	URB was rejected because the device is suspended.

``-ENOEXEC``		A control URB doesn't contain a Setup packet.
=======================	=======================================================

Error codes returned by ``in urb->status`` or in ``iso_frame_desc[n].status`` (for ISO)
=======================================================================================

USB device drivers may only test urb status values in completion handlers.
This is because otherwise there would be a race between HCDs updating
these values on one CPU, and device drivers testing them on another CPU.

A transfer's actual_length may be positive even when an error has been
reported.  That's because transfers often involve several packets, so that
one or more packets could finish before an error stops further endpoint I/O.

For isochronous URBs, the urb status value is non-zero only if the URB is
unlinked, the device is removed, the host controller is disabled, or the total
transferred length is less than the requested length and the
``URB_SHORT_NOT_OK`` flag is set.  Completion handlers for isochronous URBs
should only see ``urb->status`` set to zero, ``-ENOENT``, ``-ECONNRESET``,
``-ESHUTDOWN``, or ``-EREMOTEIO``. Individual frame descriptor status fields
may report more status codes.


===============================	===============================================
0				Transfer completed successfully

``-ENOENT``			URB was synchronously unlinked by
				:c:func:`usb_unlink_urb`

``-EINPROGRESS``		URB still pending, no results yet
				(That is, if drivers see this it's a bug.)

``-EPROTO`` [#f1]_, [#f2]_	a) bitstuff error
				b) no response packet received within the
				   prescribed bus turn-around time
				c) unknown USB error

``-EILSEQ`` [#f1]_, [#f2]_	a) CRC mismatch
				b) no response packet received within the
				   prescribed bus turn-around time
				c) unknown USB error

				Note that often the controller hardware does
				not distinguish among cases a), b), and c), so
				a driver cannot tell whether there was a
				protocol error, a failure to respond (often
				caused by device disconnect), or some other
				fault.

``-ETIME`` [#f2]_		No response packet received within the
				prescribed bus turn-around time.  This error
				may instead be reported as
				``-EPROTO`` or ``-EILSEQ``.

``-ETIMEDOUT``			Synchronous USB message functions use this code
				to indicate timeout expired before the transfer
				completed, and no other error was reported
				by HC.

``-EPIPE`` [#f2]_		Endpoint stalled.  For non-control endpoints,
				reset this status with
				:c:func:`usb_clear_halt`.

``-ECOMM``			During an IN transfer, the host controller
				received data from an endpoint faster than it
				could be written to system memory

``-ENOSR``			During an OUT transfer, the host controller
				could not retrieve data from system memory fast
				enough to keep up with the USB data rate

``-EOVERFLOW`` [#f1]_		The amount of data returned by the endpoint was
				greater than either the max packet size of the
				endpoint or the remaining buffer size.
				"Babble".

``-EREMOTEIO``			The data read from the endpoint did not fill
				the specified buffer, and ``URB_SHORT_NOT_OK``
				was set in ``urb->transfer_flags``.

``-ENODEV``			Device was removed.  Often preceded by a burst
				of other errors, since the hub driver doesn't
				detect device removal events immediately.

``-EXDEV``			ISO transfer only partially completed
				(only set in ``iso_frame_desc[n].status``,
				not ``urb->status``)

``-EINVAL``			ISO madness, if this happens: Log off and
				go home

``-ECONNRESET``			URB was asynchronously unlinked by
				:c:func:`usb_unlink_urb`

``-ESHUTDOWN``			The device or host controller has been
				disabled due to some problem that could not
				be worked around, such as a physical
				disconnect.
===============================	===============================================


.. [#f1]

   Error codes like ``-EPROTO``, ``-EILSEQ`` and ``-EOVERFLOW`` normally
   indicate hardware problems such as bad devices (including firmware)
   or cables.

.. [#f2]

   This is also one of several codes that different kinds of host
   controller use to indicate a transfer has failed because of device
   disconnect.  In the interval before the hub driver starts disconnect
   processing, devices may receive such fault reports for every request.



Error codes returned by usbcore-functions
=========================================

.. note:: expect also other submit and transfer status codes

:c:func:`usb_register`:

======================= ===================================
``-EINVAL``		error during registering new driver
======================= ===================================

``usb_get_*/usb_set_*()``,
:c:func:`usb_control_msg`,
:c:func:`usb_bulk_msg()`:

======================= ==============================================
``-ETIMEDOUT``		Timeout expired before the transfer completed.
======================= ==============================================