| Age | Commit message (Collapse) | Author |
|---|
|
Switch from using custom INTX_NUM macro to the generic PCI_NUM_INTX definition
for the number of INTx interrupts.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: use subject/changelog from similar patches]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
MT2712 and MT7622's PCIe host controller support MSI, but only 32-bit MSI
addresses are supported. It connects to GIC with the same IRQ number as the
INTx IRQ, so it shares the same IRQ with INTx IRQ.
Add MSI support for MT2712 and MT7622.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: changes to follow rcar & tegra: rename to mtk_pcie_msi_alloc(),
add mtk_pcie_msi_free(), free hwirq if irq_create_mapping() fails, call
irq_dispose_mapping() from mtk_msi_teardown_irq()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
|
|
75983c6d1f38 ("PCI: mediatek: Add controller support for MT2712 and
MT7622") has put the mtk_pcie * into bus->sysdata. Take advantage of that
to get the private data and simplify the code.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
|
|
Add controller support for MT2712/MT7622 and update related properties.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
MT2712 and MT7622 using a new IP block of Gen2 controller which has two
root ports and shares the same probing flow with MT2701/MT7623.
Both MT2712 and MT7622 have the same per-port control registers, but
there are slight differences between them:
- MT7622 has more clocks than MT2712.
- MT7622 has shared control registers which are used to enable LTSSM and
ASPM while MT2712 does not.
Add host controller support for MT2712/MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: folded in fix from http://lkml.kernel.org/r/1502715868-17651-2-git-send-email-honghui.zhang@mediatek.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
To accommodate other SoC generations, regroup specific properties by SoC,
and remove redundant descriptions.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: split into a rename patch and a cleanup patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
To accommodate other SoC generations, rename mediatek,mt7623-pcie.txt to
mediatek-pcie.txt.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: split rename to separate patch so updates are obvious]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
This is a transitional patch. We currently use platfarm_get_resource() for
retrieving the IOMEM resources, but there might be some chips don't have
subsys/shared registers part, which depends on platform design, and these
will be introduced in further patches.
Switch this function to use the platform_get_resource_byname() so that the
binding can be agnostic of the resource order.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Introduce a structure "mtk_pcie_soc" to abstract the differences between
controller generations, and the .startup() hook is used to encapsulate some
SoC-dependent related setting. In doing so, the common code which will be
reused by future chips.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Rename "port->index" to "port->slot" since the ports are hardwired at
PCI_SLOT. Also rename "mtk_pcie_parse_ports()" to "mtk_pcie_parse_port()"
since it parses one port each time.
No functional change in this patch.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Wait for Gen2 training with readl_poll_timeout(), and simplify the hardware
assert logical by merging it into a new mtk_pcie_startup_port() interface.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add support for ls1088a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
|
|
The ls2088a PCIe controller's register addresses are different from
ls2080a, so add a match entry to identify ls2088a PCIe.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
|
|
Previously we enabled writes to the DBI read-only registers so the Class
Code fix in dw_pcie_setup_rc() would work. But now dw_pcie_setup_rc()
enables write permission itself, so we don't need to do it here.
Stop enabling writes to the DBI read-only registers.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
Now that the Class Code fixup in dw_pcie_setup_rc() works, remove the fixup
from the Layerscape driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
dw_pcie_setup_rc() contains fixes to update the Class Code and Interrupt
Pin registers, but the fixes don't actually work because these registers
are read-only.
Enable write permission before updating the Class Code and Interrupt
Pin.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
The read-only DBI registers can be written only when the "Write to RO
Registers Using DBI" (DBI_RO_WR_EN) field of MISC_CONTROL_1_OFF is set.
Add accessors to enable and disable write permission, and use them instead
of accessing MISC_CONTROL_1_OFF directly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
Disable all the outbound windows to avoid one transaction hitting multiple
outbound windows. dw_pcie_setup_rc() will reconfigure the outbound
windows, which may conflict with windows configured by the bootloader.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
ls1021_pcie_host_init() duplicated the code in the generic
ls_pcie_host_init(). Call ls_pcie_host_init() instead of duplicating the
code.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
Add a missing option help line for performing legacy interrupt test.
Signed-off-by: Stan Drozd <drozdziak1@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
In certain platforms like TI's DRA7 SoCs, use of legacy PCI interrupt is
exclusive with use of MSI (Section 24.9.4.6.2.1 Legacy PCI Interrupts in
http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf).
However pci_endpoint_test driver enables MSI by default in probe. In order
for pci_endpoint_test to be able to test legacy interrupt, MSI should be
disabled. Add a module param 'no_msi' to disable MSI (only when legacy
interrupt has to be tested).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[bhelgaas: folded in static fix from Colin Ian King <colin.king@canonical.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
BAR sizes are hard-coded in pci_endpoint_test driver corresponding to the
sizes used in pci-epf-test function driver. This might break if the sizes
in pci-epf-test function driver are modified (and the corresponding change
is not done in pci_endpoint_test PCI driver).
To avoid hard coding BAR sizes, use pci_resource_len() API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some platforms like TI's K2G have a restriction that the host side buffer
address should be aligned to either 1MB/2MB/4MB or 8MB addresses depending
on how it is configured in the endpoint (Ref: 11.14.4.9.1 Outbound Address
Translation in K2G TRM SPRUHY8F January 2016 – Revised May 2017). This
restriction also applies to the MSI addresses provided by the RC. However
it's not possible for the RC to know about this restriction and it may not
provide 1MB/2MB/4MB or 8MB aligned address. So MSI interrupts should be
disabled even if the K2G EP has MSI capabiltiy register.
Add support to not enable MSI interrupts in pci_endpoint_test driver so
that it can be used to test K2G EP.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some platforms like TI's K2G have a restriction that the host side buffer
address should be aligned to either 1MB/2MB/4MB or 8MB (Ref: 11.14.4.9.1
Outbound Address Translation in K2G TRM SPRUHY8F January 2016 – Revised May
2017) addresses depending on how it is configured in the endpoint.
Add support to provide such aligned address here so that pci_endpoint_test
driver can be used to test K2G EP.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
to any BAR
pci_endpoint_test driver assumes the PCI_ENDPOINT_TEST registers will
always be mapped to BAR_0. This need not always be the case like in TI's
K2G where BAR_0 is mapped to PCI controller application registers.
Add support so that PCI_ENDPOINT_TEST registers can be mapped to any BAR.
Change the bar_size used for BAR test accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some platforms like K2G has reserved use of BAR_0 which shouldn't be
disabled by software. Avoid disabling all BARs during initialization.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
dra7xx has all base address registers (BAR) enabled by default. Reset all
BARs during initialization and so that BARs are enabled only if they are
actually used.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use the newly introduced __pci_epc_mem_init() instead of pci_epc_mem_init()
to provide page_size to pci_epc_mem. This is in preparation for
adding EP support to K2G which has a restriction that the
address region should be either divided into 1MB/2MB/4MB or 8MB
sizes (Ref: 11.14.4.9.1 Outbound Address Translation in K2G TRM SPRUHY8F
January 2016 – Revised May 2017).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
epf_test is allocated using devm_kzalloc(). Hence it's not required to
explicitly free it in remove() callback. Since ->remove() callback doesn't
do anything other than freeing epf_test, remove the ->remove() callback.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Certain platforms like TI's K2G doesn't support link-up notification. Add
support to poll early (without waiting for the linkup notification) for
commands from the host.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pci_epf_test always maps the PCI_ENDPOINT_TEST registers to BAR_0. But if
BAR_0 is reserved for some other purpose (like in TI's K2G BAR_0 is mapped
to application registers and cannot be used to map any other regions),
PCI_ENDPOINT_TEST registers cannot be mapped making pci_epf_test unusable.
Add support to use any BAR to map PCI_ENDPOINT_TEST registers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pci_epf_test_cmd_handler() is the delayed work function which reads
*command* (set by the host) and performs various actions requested by the
host periodically. If the value in *command* is '0', it goes to the
reset_handler where it resets *command* to '0' and queues
pci_epf_test_cmd_handler().
However if the host writes a value to the *command* just after the
pci-epf-test driver checks *command* for '0' and before the control goes to
reset_handler, the *command* will be reset to '0' and the pci-epf-test
driver won't be able to perform the actions requested by the host. Fix it
here by not resetting the *command* in the reset_handler.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
struct pci_epf_test_reg is the MEMSPACE of pci-epf-test function driver
that will be accessed by the "host" for programming the pci-epf-test
device. So this structure shouldn't be subjected to compiler optimization
in pci_epf_test_cmd_handler() since the values can be changed by code
outside the scope of current code at any time.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pci-epc-mem uses a page size equal to *PAGE_SIZE* (usually 4KB) to manage
the address space. However certain platforms like TI's K2G have a
restriction that this address space should be either divided into
1MB/2MB/4MB or 8MB sizes (Ref: 11.14.4.9.1 Outbound Address Translation in
K2G TRM SPRUHY8F January 2016 – Revised May 2017). Add support to handle
different page sizes here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Make ->remove() callback optional so that endpoint function drivers don't
have to populate empty ->remove() callback functions.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We will use the generic ls_pcie_link_up() and ls_pcie_host_init() from
device-specific routines. Move the generic functions earlier in the file
so we won't need forward declarations. This is strictly a code move with
no functional change intended.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
The current code depends on class code and multifunction fixups done by the
bootloader. Perform these fixups in ls1021_pcie_host_init() to remove this
dependency.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
The STRFMR1 is not a DBI read-only register, so move it out from the
write-enable bracket.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
We called dw_pcie_setup_rc() from the ls1021a host init function, but not
from the common ls_pcie_host_init() function, so platforms other than
ls1021a still depended on initialization by the bootloader.
Call dw_pcie_setup_rc() from ls_pcie_host_init() to reduce dependencies on
the bootloader.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
Call pci_unmap_iospace() to clean up if probe fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Call irq_domain_remove() to clean up if probe fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Disable vpcie0v9 regulator if resume_noirq fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We observed that the clk_pciephy_ref is still enabled when we fail to probe
the driver.
root@linaro-alip:~# grep pcie /sys/kernel/debug/clk/clk_summary
clk_pciephy_ref 1 1 24000000 0 0
clk_pcie_pm 0 0 24000000 0 0
clk_pcie_core_cru 0 0 125000000 0 0
clk_pciephy_ref100m 0 0 100000000 0 0
aclk_pcie 0 0 148500000 0 0
aclk_perf_pcie 0 0 148500000 0 0
pclk_pcie 0 0 37125000 0 0
clk_pcie_core 0 0 0 0 0
clk_pciephy_ref is used by the PHY driver and we need to properly disable
it for this case. Add error handling in rockchip_pcie_init_port() and
rockchip_pcie_resume_noirq() to fix this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_deinit_phys() so it can be reused by
rockchip_pcie_suspend_noirq() and rockchip_pcie_remove(). No functional
change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_disable_clocks() so it can be reused by other
functions.
No functional change intended, but it does change the order of unpreparing
clocks in the rockchip_pcie_resume_noirq() error path so it matches the
other paths.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_enable_clocks() so it can be reused by
rockchip_pcie_resume_noirq() and rockchip_pcie_probe().
No functional change intended, but it does change the order of unpreparing
clocks in the rockchip_pcie_resume_noirq() error path.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_setup_irq() to prepare for future bug fixes. No
functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The reset GPIO can be connected to a I2C or SPI IO expander, which may
sleep, so it is safer to use the gpiod_set_value_cansleep() variant
instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
|
