| Age | Commit message (Collapse) | Author |
|---|
|
Du Changbin reported crash [1] when calling perf_hpp__reset_output_field()
after unregistering field via perf_hpp__column_unregister().
This ends up in calling following list_del* sequence on
the same format:
perf_hpp__column_unregister:
list_del(&format->list);
perf_hpp__reset_output_field:
list_del_init(&fmt->list);
where the later list_del_init might touch already freed formats.
Fixing this by replacing list_del() with list_del_init() in
perf_hpp__column_unregister().
[1] http://marc.info/?l=linux-kernel&m=149059595826019&w=2
Reported-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20171013083736.15037-2-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
SMBUS_BLOCK_DATA transactions might fail due to a race condition with
the IMC (Integrated Micro Controller), even when the IMC semaphore
is used.
This bug has been reported and confirmed by AMD, who suggested as a
solution an IMC firmware upgrade (obtained via BIOS update) and
disabling the IMC during SMBUS_BLOCK_DATA transactions.
Even without the IMC upgrade, the SMBUS is much more stable with this
patch.
Tested on a Bettong-alike board.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
AMD Family 17h uses the KERNCZ SMBus controller. While its documentation
is not publicly available, it is documented in the BIOS and Kernel
Developer’s Guide for AMD Family 15h Models 60h-6Fh Processors.
On this SMBus controller, the port select register is at PMx register
0x02, bit 4:3 (PMx00 register bit 20:19).
Without this patch, the 4 SMBus channels on AMD Family 17h chips are
mirrored and report the same chips on all channels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
The arguments for SDA and SCL were swapped. Fix it.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some SoC share one irq number between I2C controllers.
For example, on the LS2088 board, I2C 1 and I2C 2 share
one irq number. In this case, only one I2C controller
can register successfully, and others will fail.
Signed-off-by: Wei Jinhua <wei.jinhua1@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- keep an important data structure in the Exynos driver around after
kernel-init to fix a kernel-oops
- keep SWIOTLB enabled when SME is active in the AMD IOMMU driver
- add a missing IOTLB sync to the AMD IOMMU driver
* tag 'iommu-fixes-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Finish TLB flush in amd_iommu_unmap()
iommu/exynos: Remove initconst attribute to avoid potential kernel oops
iommu/amd: Do not disable SWIOTLB if SME is active
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Fix memory leak in error case of of_console_check
- Increase number of reserved memory regions to 32. 16 was not enough
on some Power systems.
- Fix OF node refcounting for of_fwnode_graph_get_port_parent
* tag 'devicetree-fixes-for-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
device property: preserve usecount for node passed to of_fwnode_graph_get_port_parent()
drivers: of: increase MAX_RESERVED_REGIONS to 32
of: do not leak console options
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A fix for a bad bug (written by me) in our livepatch handler. Removal
of an over-zealous lockdep_assert_cpus_held() in our topology code. A
fix to the recently added emulation of cntlz[wd]. And three small
fixes to the recently added IMC PMU driver.
Thanks to: Anju T Sudhakar, Balbir Singh, Kamalesh Babulal, Naveen N.
Rao, Sandipan Das, Santosh Sivaraj, Thiago Jung Bauermann"
* tag 'powerpc-4.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/perf: Fix IMC initialization crash
powerpc/perf: Add ___GFP_NOWARN flag to alloc_pages_node()
powerpc/perf: Fix for core/nest imc call trace on cpuhotplug
powerpc: Don't call lockdep_assert_cpus_held() from arch_update_cpu_topology()
powerpc/lib/sstep: Fix count leading zeros instructions
powerpc/livepatch: Fix livepatch stack access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixlet from Juergen Gross:
"A minor fix correcting the cpu hotplug name for Xen guests"
* tag 'for-linus-4.14c-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/vcpu: Use a unified name about cpu hotplug state for pv and pvhvm
|
|
Commit b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for
block reads") broke I2C block reads. It aimed to fix normal SMBus block
read, but changed the correct behavior of I2C block read in the process.
According to Documentation/i2c/smbus-protocol, one vital difference
between normal SMBus block read and I2C block read is that there is no
byte count prefixed in the data sent on the wire:
SMBus Block Read: i2c_smbus_read_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Count] A [Data] A [Data] A ... A [Data] NA P
I2C Block Read: i2c_smbus_read_i2c_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Data] A [Data] A ... A [Data] NA P
Therefore the two transaction types need to be processed differently in
the driver by copying of the dma_buffer as done previously for the
I2C_SMBUS_I2C_BLOCK_DATA case.
Fixes: b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for block reads")
Signed-off-by: Pontus Andersson <epontan@gmail.com>
Tested-by: Stephen Douthit <stephend@adiengineering.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Untangle intel_enable_ddi() by splitting it into DP and HDMI specific
variants.
v2: Keep using intel_ddi_get_encoder_port() for now
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Rather that plumb the link parameters separately to
intel_ddi_pre_enable_dp() let's just pass the entire crtc state.
intel_ddi_pre_enable_hdmi() already took the crtc state, but for some
reason intel_ddi_pre_enable() still wanted to extract has_infoframe
from therein and pass it in separately. Let's not do that since it's
pointless.
v2: Rebase due to more code getting pulled into the DDI hooks
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Untangle intel_disable_ddi() by splitting it into DP and HDMI specific
variants.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
intel_edp_panel_on() will itself do the is_edp() check, so the caller
doesn't have to bother. Pre-DDI code doesn't bother, so let's follow the
same approach for DDI.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-7-ville.syrjala@linux.intel.com
|
|
To clean up the mess in intel_ddi_post_disable() split it into two
clean variants for HDMI and DP.
v2: Rebase due to MST DPMS changes
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-6-ville.syrjala@linux.intel.com
|
|
intel_ddi_fdi_post_disable()
To untangle the mess that is intel_ddi_post_disable() move the the bits
needed by FDI into intel_ddi_fdi_post_disable(). This way we can stop
worrying about FDI in intel_ddi_post_disable().
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-5-ville.syrjala@linux.intel.com
|
|
Extract the code to disable the DDI_BUF_CTL into small helper. This
will allows us to detangle the encoder type mess in
intel_ddi_post_disable().
v2: Keep using intel_ddi_get_encoder_port() for now
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-4-ville.syrjala@linux.intel.com
|
|
Pull the code to disable the port clock into a function. We already have
the intel_ddi_clk_select() counterpart.
v2: Keep using intel_ddi_get_encoder_port() for now (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
To make it easier to debug things let's dump the output types bitmask in
the crtc state dump. And to make life that much better, let's pretty
print it as a a human reaadable string as well.
v2: Have the caller pass in the buffer (Chris)
#undef OUTPUT_TYPE (Jani)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
function
The DMA reset timeout, used in read_poll_timeout, is
ten times shorter than the sleep time.
This patch fixes these values interchanging them, as it was
before the read_poll_timeout introduction.
Fixes: 8a70aeca80c2 ("net: stmmac: Use readl_poll_timeout")
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While experimenting with changes to the timekeeping code, I
ran into a build error in the liquidio driver:
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'liquidio_ptp_settime':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1850:22: error: passing argument 1 of 'timespec_to_ns' from incompatible pointer type [-Werror=incompatible-pointer-types]
The driver had a type mismatch since it was first merged, but
this never caused problems because it is only built on 64-bit
architectures that define timespec and timespec64 to the same
type.
If we ever want to compile-test the driver on 32-bit or change
the way that 64-bit timespec64 is defined, we need to fix it,
so let's just do it now.
Fixes: f21fb3ed364b ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Nothing really special standing out, all of these are important fixes
which should go to 4.14.
iwlwifi
* fix support for 3168 device series
* fix a potential crash when using FW debugging recording;
* improve channel flags parsing to avoid warnings on too long traces
* return -ENODATA when the temperature is not available, since the
-EIO we were returning was causing fatal errors in userspace
* avoid printing too many messages in dmesg when using monitor mode,
since this can become very noisy and completely flood the logs
brcmsmac
* reduce stack usage to avoid frame size warnings with KASAN
brcmfmac
* add a check to avoid copying uninitialised memory
rtlwifi:
* fix a regression with rtl8821ae starting from v4.11 where
connections was frequently lost
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the driver is relying on the atomic helpers, remove the explicit
.best_encoder assignment and let the core call
drm_atomic_helper_best_encoder().
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010205858.GA4806@Haneen
|
|
Convert instances of dev_error to DRM_DEV_ERROR as we have
DRM_DEV_ERROR variants of drm print macros.
Signed-off-by: Harsha Sharma <harshasharmaiitr@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171006221738.30200-1-harshasharmaiitr@gmail.com
|
|
The function only sends the flush command to the IOMMU(s),
but does not wait for its completion when it returns. Fix
that.
Fixes: 601367d76bd1 ('x86/amd-iommu: Remove iommu_flush_domain function')
Cc: stable@vger.kernel.org # >= 2.6.33
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Any usage of the irq_gc_mask_disable_reg_and_ack() function has
been replaced with the desired functionality.
The incorrect and ambiguously named function is removed here to
prevent accidental misuse.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The only usage of the irq_gc_mask_disable_reg_and_ack() function
is by the Tango irqchip driver. This usage is replaced by the
irq_gc_mask_disable_and_ack_set() function since it provides the
intended functionality.
Fixes: 4bba66899ac6 ("irqchip/tango: Add support for Sigma Designs SMP86xx/SMP87xx interrupt controller")
Acked-by: Mans Rullgard <mans@mansr.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The irq_gc_mask_disable_reg_and_ack() function name implies that it
provides the combined functions of irq_gc_mask_disable_reg() and
irq_gc_ack(). However, the implementation does not actually do
that since it writes the mask instead of the disable register. It
also does not maintain the mask cache which makes it inappropriate
to use with other masking functions.
In addition, commit 659fb32d1b67 ("genirq: replace irq_gc_ack() with
{set,clr}_bit variants (fwd)") effectively renamed irq_gc_ack() to
irq_gc_ack_set_bit() so this function probably should have also been
renamed at that time.
The generic chip code currently provides three functions for use
with the irq_mask member of the irq_chip structure and two functions
for use with the irq_ack member of the irq_chip structure. These
functions could be combined into six functions for use with the
irq_mask_ack member of the irq_chip structure. However, since only
one of the combinations is currently used, only the function
irq_gc_mask_disable_and_ack_set() is added by this commit.
The '_reg' and '_bit' portions of the base function name were left
out of the new combined function name in an attempt to keep the
function name length manageable with the 80 character source code
line length while still allowing the distinct aspects of each
combination to be captured by the name.
If other combinations are desired in the future please add them to
the irq generic chip library at that time.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The current ITS driver works fine as long as normal memory and GICR
regions are located within the lower 48bit (>=0 && <2^48) physical
address space. Some of the registers GICR_PEND/PROP, GICR_VPEND/VPROP
and GITS_CBASER are handled properly but not all when configuring
the hardware with 52bit physical address.
This patch does the following changes to support 52bit PA.
-Handle 52bit PA in GITS_BASERn.
-Fix ITT_addr width to 52bits, bits[51:8].
-Fix RDbase width to 52bits, bits[51:16].
-Fix VPT_addr width to 52bits, bits[51:16].
Definition of the GITS_BASERn register when ITS PageSize is 64KB:
-Bits[47:16] of the register provide bits[47:16] of the table PA.
-Bits[15:12] of the register provide bits[51:48] of the table PA.
-Bits[15:00] of the base physical address are 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The VCPU table consists of vPE entries, and its size provides the number
of VPEs supported by GICv4 hardware. Unfortunately the maximum size of
the VPE table is not discoverable like Device table. All VLPI commands
limits the number of bits to 16 to hold VPEID, which is index into VCPU
table. Don't apply DEVID bits for VCPU table instead assume maximum bits
to 16.
ITS log messages on QDF2400 without fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
Virtual CPUs Table too large, reduce ids 32->26
Virtual CPUs too large, reduce ITS pages 8192->256
allocated 2097152 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
ITS log messages on QDF2400 with fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
allocated 65536 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The driver probe path hits 'BUG_ON(entries != vpe_proxy.dev->nr_ites)'
on systems where it has VLPI capability, doesn't support direct LPI
feature and boot with a single CPU.
Relax the BUG_ON() condition to fix the issue.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Core drm shouldn't depend on anything in drm-kms-helper, or the drm
module will fail to load.
insmod drm fails with
[ 6087.674390] drm: Unknown symbol drm_panel_bridge_remove (err 0)
which is defined in drm_kms_helper.ko
This call was added by commit c70087e8f16f ("drm/drm_of: add
drm_of_panel_bridge_remove function"), and the fix is defining it in the
drm_of.h header, to break the circular dependency.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8f95e623-9480-97dc-2414-77086d8aa49d@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com> #irc
Fixes: c70087e8f16f ("drm/drm_of: add drm_of_panel_bridge_remove function")
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
Replace instances of drm_framebuffer_reference/unreference() with
*_get/put() suffixes and drm_dev_unref with *_put() suffix
because get/put is shorter and consistent with the
kernel use of *_get/put suffixes.
Done with following coccinelle semantic patch
@@
expression ex;
@@
(
-drm_framebuffer_unreference(ex);
+drm_framebuffer_put(ex);
|
-drm_dev_unref(ex);
+drm_dev_put(ex);
|
-drm_framebuffer_reference(ex);
+drm_framebuffer_get(ex);
)
Signed-off-by: Harsha Sharma <harshasharmaiitr@gmail.com>
[danvet: Drop the drm_dev_put change for now, to make the patch apply
with out a backmerge.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171009120643.11953-1-harshasharmaiitr@gmail.com
|
|
Favor for_each_pipe() macro when looping through pipes.
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507890286-16214-1-git-send-email-mika.kahola@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
Fix up this reference so that the proper link is generated in the
documentation and so that people don't go chasing after the wrong
function for an embarrassingly long time.
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012140857.9559-1-thierry.reding@gmail.com
|
|
Fix "esay-to-use" to "easy-to-use" typo.
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012140616.9002-1-thierry.reding@gmail.com
|
|
'user_handles' needs a __user annotation for fix the following sparse
warning:
drm_syncobj.c:813:37: warning: incorrect type in argument 2 (different address spaces)
drm_syncobj.c:813:37: expected void const [noderef] <asn:1>*from
drm_syncobj.c:813:37: got void *user_handles
drm_syncobj.c:875:38: warning: incorrect type in argument 2 (different address spaces)
drm_syncobj.c:875:38: expected void *user_handles
drm_syncobj.c:875:38: got void [noderef] <asn:1>*<noident>
drm_syncobj.c:908:38: warning: incorrect type in argument 2 (different address spaces)
drm_syncobj.c:908:38: expected void *user_handles
drm_syncobj.c:908:38: got void [noderef] <asn:1>*<noident>
drm_syncobj.c:941:38: warning: incorrect type in argument 2 (different address spaces)
drm_syncobj.c:941:38: expected void *user_handles
drm_syncobj.c:941:38: got void [noderef] <asn:1>*<noident>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Fixes: 3e6fb72d6cef ("drm/syncobj: Add a syncobj_array_find helper")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170901165328.24459-2-ville.syrjala@linux.intel.com
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
Currently, the examples are using 2MB for the ITS size. Per the
specification (section 8.18 in ARM IHI 0069D), the ITS address map is
128KB.
Update the examples to match the specification.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
of_fdt_unflatten_tree() already sets the flag on this node to
OF_DETACHED, because of_fdt_unflatten_tree() calls
__unflatten_device_tree() with the detached bool set to true.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
We need the total frame refresh time to check if we are too close to
vertical sync when updating the two framebuffer DMA registers and risk
a collision. This new method is more accurate that the previous that
based on mode's vrefresh value, which itself is inaccurate or may not
even be initialized.
Reported-by: Kevin Hao <kexin.hao@windriver.com>
Fixes: 11abbc9f39e0 ("drm/tilcdc: Set framebuffer DMA address to HW only if CRTC is enabled")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We read the dp dual mode Adapter identifier to detect the
LSPCON device. It's been observed from the CI testing that in
few cases, this read can get delayed or fail. For such scenarios,
LSPCON vendors suggest to retry the read operation.
This patch adds retry in the probe function, while reading
LSPCON identifier.
V3: added this patch in the series
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102294
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102295
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102359
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103186
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630064-17908-4-git-send-email-shashank.sharma@intel.com
|
|
Our current logic to read LSPCON's current mode, stops retries and
breaks wait-loop, if it gets LSPCON_MODE_INVALID as return from the
core function. This doesn't allow us to try reading the mode again.
This patch removes this condition and allows retries reading
the currnt mode until timeout.
This also fixes/prevents some of the noise in form of debug messages
while running IGT CI test cases.
V2: rebase, added r-b
V2: changed some debug message levels from debug->error and
error->debug in lspcon_get_current_mode function.
V3: Rebase
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102294
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102295
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102359
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103186
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Mahesh Kumar <Mahesh1.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630064-17908-3-git-send-email-shashank.sharma@intel.com
|
|
From the CI builds, its been observed that during a driver
reload/insert, dp dual mode read function sometimes fails to
read from LSPCON device over i2c-over-aux channel.
This patch:
- adds some delay and few retries, allowing a scope for these
devices to settle down and respond.
- changes one error log's level from ERROR->DEBUG as we want
to call it an error only after all the retries are exhausted.
V2: Addressed review comments from Jani (for loop for retry)
V3: Addressed review comments from Imre (break on partial read too)
V3: Addressed review comments from Ville/Imre (Add the retries
exclusively for LSPCON, not for all dp_dual_mode devices)
V4: Added r-b from Imre, sending it to dri-devel (Jani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102294
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102295
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102359
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103186
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507826408-19322-1-git-send-email-shashank.sharma@intel.com
|
|
Panic observed with latest firmware, and upstream kernel:
NIP init_imc_pmu+0x8c/0xcf0
LR init_imc_pmu+0x2f8/0xcf0
Call Trace:
init_imc_pmu+0x2c8/0xcf0 (unreliable)
opal_imc_counters_probe+0x300/0x400
platform_drv_probe+0x64/0x110
driver_probe_device+0x3d8/0x580
__driver_attach+0x14c/0x1a0
bus_for_each_dev+0x8c/0xf0
driver_attach+0x34/0x50
bus_add_driver+0x298/0x350
driver_register+0x9c/0x180
__platform_driver_register+0x5c/0x70
opal_imc_driver_init+0x2c/0x40
do_one_initcall+0x64/0x1d0
kernel_init_freeable+0x280/0x374
kernel_init+0x24/0x160
ret_from_kernel_thread+0x5c/0x74
While registering nest imc at init, cpu-hotplug callback
nest_pmu_cpumask_init() makes an OPAL call to stop the engine. And if
the OPAL call fails, imc_common_cpuhp_mem_free() is invoked to cleanup
memory and cpuhotplug setup.
But when cleaning up the attribute group, we are dereferencing the
attribute element array without checking whether the backing element
is not NULL. This causes the kernel panic.
Add a check for the backing element prior to dereferencing the
attribute element, to handle the failing case gracefully.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
[mpe: Trim change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Per BSpec, 400us is "BDW+ Do not use this setting." - not just PORT_A.
Set BDW to 600us unconditionally.
v2:
-Split in to two patches (Rodrigo)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012213037.4245-2-james.ausmus@intel.com
|
|
Rename DP_AUX_CH_CTL_TIME_OUT_1600us to DP_AUX_CH_CTL_TIME_OUT_MAX, as
the meaning of the (3 << 26) value varies per platform, but it's always the
maximum timeout for that platform. Pre-CNL it means 1600us, and for CNL
it means 3200us.
v2:
-Split in to two patches (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012213037.4245-1-james.ausmus@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for 4.15
* OMAP4 HDMI CEC support
* tag 'omapdrm-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
omapdrm: omapdss_hdmi_ops: add lost_hotplug op
omapdrm: hdmi4: hook up the HDMI CEC support
omapdrm: hdmi4_cec: add OMAP4 HDMI CEC support
omapdrm: hdmi4: refcount hdmi_power_on/off_core
omapdrm: hdmi4: move hdmi4_core_powerdown_disable to hdmi_power_on_core()
omapdrm: hdmi4: prepare irq handling for HDMI CEC support
omapdrm: hdmi4: make low-level functions available
omapdrm: hdmi.h: extend hdmi_core_data with CEC fields
omapdrm: encoder-tpd12s015: keep ls_oe_gpio high
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: i.MX5 regression fix and i.MX6QP PRE/PRG stability fixes
- Disable channel burst locking on IPUv3EX (i.MX51) and IPUv3M (i.MX53).
This fixes a regression introduced by commit 790cb4c7c954 ("drm/imx: lock
scanout transfers for consecutive bursts").
- Give PRG a head start. Waiting for both double buffers to fill up before
enabling the IPU improves startup reliability.
- Avoid PRE control register updates during unsafe window, workaround for
ERR009624.
* tag 'imx-drm-fixes-2017-10-12' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: pre: implement workaround for ERR009624
gpu: ipu-v3: prg: wait for double buffers to be filled on channel startup
gpu: ipu-v3: Allow channel burst locking on i.MX6 only
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
More 4.15 drm-misc stuff:
Cross-subsystem Changes:
- bridge cleanup refactor (Benjamin Gaignard)
Core Changes:
- less surprising atomic iterators (Maarten), fixes an oops introduced
in drm-next
- better gem/fb helper docs (Noralf)
- fix dma-buf rcu races (Christian König)
Driver Changes:
- adv7511: CEC support (Hans Verkuil)
- sun4i update from Chen-Yu to improve hdmi and A31 support
- sii8620: add remote control support (Maceiej Purski)
New drivers:
- SiI9234 bridge driver (Maciej Purski)
- 7" rpi touch panel (Eric Anholt)
Note that this contains a topic pull from regmap, needed by the sun4i
changes. Mark Brown sent that out for pulling into drm-misc.
* tag 'drm-misc-next-2017-10-12' of git://anongit.freedesktop.org/drm/drm-misc: (29 commits)
drm/dp: WARN about invalid/unknown link rates and bw codes
drm/msm/mdp5: remove less than 0 comparison for unsigned value
drm/bridge/sii8620: add remote control support
drm/sun4i: hdmi: Add support for A31's HDMI controller
drm/sun4i: hdmi: Add A31 specific DDC register definitions
drm/sun4i: hdmi: Add support for controller hardware variants
dt-bindings: display: sun4i: Add binding for A31 HDMI controller
drm/sun4i: hdmi: Allow using second PLL as TMDS clk parent
drm/sun4i: hdmi: create a regmap for later use
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/sun4i: tcon: Add support for demuxing TCON output on A31
drm/sun4i: tcon: Add variant callback for TCON output muxing
drm/bridge/synopsys: dsi :remove is_panel_bridge
drm/vc4: remove bridge from driver internal structure
drm/stm: ltdc: remove bridge from driver internal structure
drm/drm_of: add drm_of_panel_bridge_remove function
drm/bridge: make drm_panel_bridge_remove more robust
dma-fence: fix dma_fence_get_rcu_safe v2
dma-buf: make reservation_object_copy_fences rcu save
drm/atomic: Unref duplicated drm_atomic_state in drm_atomic_helper_resume()
...
|
|
into drm-fixes
single amdgpu regression fix.
* 'drm-fixes-4.14' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix placement flags in amdgpu_ttm_bind
|
