| Age | Commit message (Collapse) | Author |
|---|
|
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use __maybe_unused for PM functions instead of ifdeffery.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
For better maintenance group MODULE_*() macros together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add a note about struct dw_scl_sda_cfg usage to discourage people
of using this structure on new platforms. Instead they should try
hard to put the needed information into firmware descriptions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Intel Keem Bay platform supports multi-master operations over same i2c
bus using Synopsys i2c DesignWare IP. When multi-masters initiate i2c
operation simultaneously in a loop, SCL line is stucked low forever
after few i2c operations. Following interrupt sequences are observed
in:
working case: TX_EMPTY, RX_FULL and STOP_DET
non working case: TX_EMPTY, STOP_DET, RX_FULL.
DW_apb_i2c stretches the SCL line when the TX FIFO is empty or when
RX FIFO is full. The DW_apb_i2c master will continue to hold the SCL
line LOW until RX FIFO is read.
Linux kernel i2c DesignWare driver does not handle above non working
sequence. TX_EMPTY, RX_FULL and STOP_DET routine execution are required
in sequence although RX_FULL interrupt is raised after STOP_DET by
hardware. Clear STOP_DET for the following conditions:
(STOP_DET ,RX_FULL, rx_outstanding)
Write Operation: (1, 0, 0)
Read Operation:
RX_FULL followed by STOP_DET: (0, 1, 1) -> (1, 0, 0)
STOP_DET followed by RX_FULL: (1, 0, 1) -> (1, 1, 0)
RX_FULL and STOP_DET together: (1, 1, 1)
Signed-off-by: Tamal Saha <tamal.saha@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into media_tree
Signed tag for the immutable platform-drivers-x86-int3472 branch
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches.
* tag 'platform-drivers-x86-int3472-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: int3472: Deal with probe ordering issues
platform/x86: int3472: Pass tps68470_regulator_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Pass tps68470_clk_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Add get_sensor_adev_and_name() helper
platform/x86: int3472: Split into 2 drivers
platform_data: Add linux/platform_data/tps68470.h file
i2c: acpi: Add i2c_acpi_new_device_by_fwnode() function
i2c: acpi: Use acpi_dev_ready_for_enumeration() helper
ACPI: delay enumeration of devices with a _DEP pointing to an INT3472 device
|
|
Change i2c_acpi_new_device() into i2c_acpi_new_device_by_fwnode() and
add a static inline wrapper providing the old i2c_acpi_new_device()
behavior.
This is necessary because in some cases we may only have access
to the fwnode / acpi_device and not to the matching physical-node
struct device *.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-4-hdegoede@redhat.com
|
|
The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.
To work around cases where this info is not present in the firmware tables,
which is often the case on x86/ACPI devices, both frameworks allow the
provider-driver to attach info about consumers to the clks/regulators
when registering these.
This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.
To ensure the correct probe-ordering the ACPI core has code to defer the
enumeration of consumers affected by this until the providers are ready.
Call the new acpi_dev_ready_for_enumeration() helper to avoid
enumerating / instantiating i2c-clients too early.
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-3-hdegoede@redhat.com
|
|
Maxime points out that the polling code in mpc_i2c_isr should use the
_atomic API because it is called in an irq context and that the
behaviour of the MCF bit is that it is 1 when the byte transfer is
complete. All of this means the original code was effectively a
udelay(100).
Fix this by using readb_poll_timeout_atomic() and removing the negation
of the break condition.
Fixes: 4a8ac5e45cda ("i2c: mpc: Poll for MCF")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use i2c_timings struct and corresponding methods to get bus clock frequency
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In interrupt mode we clear the status flags twice, in the interrupt
handler and in i801_check_post(). Remove clearing the status flags
from i801_check_post() and handle polling mode by using the
SMBus unlocking write to also clear the status flags if still set.
To be precise: One could still argue that the status flags are
cleared twice in interrupt mode, but it comes for free.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I see no need to read back the registers to verify that the bits
have actually been cleared. I can't imagine any scenario where
the bits would remain set after a write to them.
Whilst at it, change involved syslog messages to use pci_dbg() et al.
to simplify them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I2C controller chosen by I2C_EXYNOS5 config option is also suitable for
Exynos850 and ExynosAutoV9 SoCs. State that specifically in I2C_EXYNOS5
symbol help section.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In new Exynos SoCs (like Exynos850) where HSI2C is implemented as a
part of USIv2 block, there are two clocks provided to HSI2C controller:
- PCLK: bus clock (APB), provides access to register interface
- IPCLK: operating IP-core clock; SCL is derived from this one
Both clocks have to be asserted for HSI2C to be functional in that case.
Add code to obtain and enable/disable PCLK in addition to already
handled operating clock. Make it optional though, as older Exynos SoC
variants only have one HSI2C clock.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
ExynosAutoV9 functioning logic mostly follows I2C_TYPE_EXYNOS7, but
timing calculation and configuration procedure is changed: e.g. only
timing_s3 has to be set now.
Another change of HSI2C controller in ExynosAutoV9 SoC is that it's now
a part of USIv2 IP-core. No changes is needed for I2C driver though, as
all USI related configuration is done in USI driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver currently assumes that the notify callback is only received
when the device is done with all the queued buffers.
However, this is not true, since the notify callback could be called
without any of the queued buffers being completed (for example, with
virtio-pci and shared interrupts) or with only some of the buffers being
completed (since the driver makes them available to the device in
multiple separate virtqueue_add_sgs() calls).
This can lead to incorrect data on the I2C bus or memory corruption in
the guest if the device operates on buffers which are have been freed by
the driver. (The WARN_ON in the driver is also triggered.)
BUG kmalloc-128 (Tainted: G W ): Poison overwritten
First byte 0x0 instead of 0x6b
Allocated in i2cdev_ioctl_rdwr+0x9d/0x1de age=243 cpu=0 pid=28
memdup_user+0x2e/0xbd
i2cdev_ioctl_rdwr+0x9d/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in i2cdev_ioctl_rdwr+0x1bb/0x1de age=68 cpu=0 pid=28
kfree+0x1bd/0x1cc
i2cdev_ioctl_rdwr+0x1bb/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Fix this by calling virtio_get_buf() from the notify handler like other
virtio drivers and by actually waiting for all the buffers to be
completed.
Fixes: 3cfc88380413d20f ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The log messages talk about 'bus recovery' while it is not a bus
recovery with 9 pulses but merely a controller reset. Controller resets
are not worth log messages. The 'bus busy' message should be emitted by
upper layers, a busy bus may be expected in some cases.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
|
|
Function stm32f7_i2c_release_bus is always returning 0, hence it
should be a void function. Update the function and remove the
return value error checking code in caller functions.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit e8578547ce59ddba3651ac0e68dbcb6daa8ce790. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit 36af188f795bd1b0d794dd735623979dc6b698d3. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we use dmaengine_terminate_sync in
i2c_xfer and i2c_smbus_xfer handlers and rely on
dmaengine_terminate_async within interrupt handlers
(transmission error cases).
dmaengine_synchronize is added within i2c_xfer and i2c_smbus_xfer handler
to finalize terminate started in interrupt handlers.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When getting an access timeout, ensure that the bus is in a proper
state prior to returning the error.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The platform data structures are used in the respective i801_add_tco
functions only. Therefore we can make the definitions local to these
functions.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Set optimal HCNT, LCNT and hold time values for all the speeds supported
in Intel Programmable Service Engine I2C controller in Intel Elkhart
Lake.
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add support to configure HCNT, LCNT values for Fast Mode Plus and High
Speed Mode.
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This enables the async suspend for i2c client devices. This reduces
the suspend/resume time considerably on platforms where i2c devices
can take a lot of time (hundreds of ms) to resume.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Enable async suspend/resume of i2c adapters. It enormously helps with
reducing the resume time of systems (as much as 20%-40%) where I2C devices
can take significant time (100s of ms) to resume.
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Mark the designware devices for asynchronous suspend. With this, the
resume for designware devices does not get stuck behind other unrelated
devices (e.g. intel_backlight that takes hundreds of ms to resume,
waiting for its parent devices).
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
$ scripts/kernel-doc -none drivers/i2c/busses/i2c-designware-core.h
warning: Function parameter or member 'rst' not described in 'dw_i2c_dev'
warning: Function parameter or member 'get_clk_rate_khz' not described in 'dw_i2c_dev'
warning: Function parameter or member 'flags' not described in 'dw_i2c_dev'
warning: Function parameter or member 'functionality' not described in 'dw_i2c_dev'
warning: Function parameter or member 'master_cfg' not described in 'dw_i2c_dev'
warning: Function parameter or member 'set_sda_hold_time' not described in 'dw_i2c_dev'
warning: Function parameter or member 'rinfo' not described in 'dw_i2c_dev'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Randy Dunlap <rdunla@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
clk_get_rate() is documented as requiring the clock to be enabled.
Ensure that the bus clock is enabled before calling clk_get_rate() in
rk3x_i2c_probe() to satisfy this requirement.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reduce source code and code size by defining the chip features
statically.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If FEATURE_BLOCK_BUFFER is set then bit SMBAUXCTL_E32B is supported
and there's no benefit in reading it back. Origin of this check
seems to be 14 yrs ago when people were not completely sure which
chip versions support the block buffer mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
CBUS transfers have always been atomic, but after commit 63b96983a5dd
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5dd ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add support for the ACPI based device registration so that the driver
can be also enabled through ACPI table.
This does not include the ACPI support for Tegra VI and DVC I2C.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
|
|
Use array_size() helper to aid in 2-factor allocation instances.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We have a special helper to get fwnode out of struct device.
Moreover, dereferencing it directly prevents the fwnode
modifications in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Recently ACPI gained the acpi_get_local_address() API which may be used
instead of home grown i2c_mux_gpio_get_acpi_adr().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Most IMX I2C interfaces don't generate an interrupt on a stop condition,
so it won't generate a timely stop event on a slave mode transfer.
Some users, like IPMB, need a timely stop event to work properly.
So, add a timer and add the proper handling to generate a stop event in
slave mode if the interface goes idle.
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If a timeout is hit, it can result is incorrect data on the I2C bus
and/or memory corruptions in the guest since the device can still be
operating on the buffers it was given while the guest has freed them.
Here is, for example, the start of a slub_debug splat which was
triggered on the next transfer after one transfer was forced to timeout
by setting a breakpoint in the backend (rust-vmm/vhost-device):
BUG kmalloc-1k (Not tainted): Poison overwritten
First byte 0x1 instead of 0x6b
Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29
__kmalloc+0xc2/0x1c9
virtio_i2c_xfer+0x65/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29
kfree+0x1bd/0x1cc
virtio_i2c_xfer+0x32e/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
There is no simple fix for this (the driver would have to always create
bounce buffers and hold on to them until the device eventually returns
the buffers), so just disable the timeout support for now.
Fixes: 3cfc88380413d20f ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Jie Deng <jie.deng@intel.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Currently interrupt storm will occur from i2c-i801 after first
transaction if SMB_ALERT signal is enabled and ever asserted. It is
enough if the signal is asserted once even before the driver is loaded
and does not recover because that interrupt is not acknowledged.
This fix aims to fix it by two ways:
- Add acknowledging for the SMB_ALERT interrupt status
- Disable the SMB_ALERT interrupt on platforms where possible since the
driver currently does not make use for it
Acknowledging resets the SMB_ALERT interrupt status on all platforms and
also should help to avoid interrupt storm on older platforms where the
SMB_ALERT interrupt disabling is not available.
For simplicity this fix reuses the host notify feature for disabling and
restoring original register value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177311
Reported-by: ck+kernelbugzilla@bl4ckb0x.de
Reported-by: stephane.poignant@protonmail.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If driver interrupts are enabled, SMBHSTCNT_INTREN will be 1 after
the first transaction, and will stay to that value forever. This
means that interrupts will be generated for both host-initiated
transactions and also SMBus Alert events even after the driver is
unloaded. To be on the safe side, we should restore the initial state
of this bit at suspend and reboot time, as we do for several other
configuration bits already and for the same reason: the BIOS should
be handed the device in the same configuration state in which we
received it. Otherwise interrupts may be generated which nobody
will process.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commits 95b8a5e0111a ("MIPS: Remove NETLOGIC support") and edd4488aea9c
("ARM: remove tango platform") removed Netlogic XLR and Sigma Designs
Tango platforms which means there are no platforms using the XLR I2C
driver and it can be removed.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Netlogic XLP was removed in commit 95b8a5e0111a ("MIPS: Remove NETLOGIC
support"). With those gone, the single platform left to support is
Cavium ThunderX2. Remove the Netlogic variant and DT support.
For simplicity, the existing kconfig name is retained.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by George Cherian <gcherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
