| Age | Commit message (Collapse) | Author |
|---|
|
When stress-testing the system by repeatedly unbinding and binding the ADC
device in a loop, and the ADC is a supplier for another device (e.g., a
thermal hardware block that reads temperature through the ADC), it may
happen that the ADC device is runtime-resumed immediately after runtime PM
is enabled, triggered by its consumer. At this point, since drvdata is not
yet set and the driver's runtime PM callbacks rely on it, a crash can
occur. To avoid this, set drvdata just after it was allocated.
Fixes: 89ee8174e8c8 ("iio: adc: rzg2l_adc: Simplify the runtime PM code")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20250810123328.800104-3-claudiu.beznea.uj@bp.renesas.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There is no need to manually track the runtime PM status in the driver.
The pm_runtime_force_suspend() and pm_runtime_force_resume() functions
already call pm_runtime_status_suspended() to check the runtime PM state.
Additionally, avoid calling pm_runtime_put_autosuspend() during the
suspend/resume path, as this would decrease the usage counter of a
potential user that had the ADC open before the suspend/resume cycle.
Fixes: 563cf94f9329 ("iio: adc: rzg2l_adc: Add suspend/resume support")
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20250810123328.800104-2-claudiu.beznea.uj@bp.renesas.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add max_conversion_rate_hz to the chip info for "adaq4381-4". Without
this, the driver fails to probe because it tries to set the initial
sample rate to 0 Hz, which is not valid.
Fixes: bbeaec81a03e ("iio: ad7380: add support for SPI offload")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250811-iio-adc-ad7380-fix-missing-max_conversion_rate_hs-on-ad4381-4-v1-1-ffb728d7a71c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One core change removing the 'w' access flag of attributes that don't
have a set routine (and therefore can't be written to) which should
have no practical impact. The big scsi_debug update is caused by
reformatting lots of arrays and the rest of the bug fixes in drivers
are trivial"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove error print for devm_add_action_or_reset()
scsi: ufs: mediatek: Fix out-of-bounds access in MCQ IRQ mapping
scsi: lpfc: Remove redundant assignment to avoid memory leak
scsi: lpfc: Fix wrong function reference in a comment
scsi: ufs: core: Fix interrupt handling for MCQ Mode
scsi: scsi_debug: Make read-only arrays static const
scsi: core: sysfs: Correct sysfs attributes access rights
|
|
The bd79124 has ADC inputs which can be muxed to be GPIOs. The driver
supports this by registering a GPIO-chip for channels which aren't used
as ADC.
The Kconfig entry does not handle the dependency to GPIOLIB, which
causes errors:
ERROR: modpost: "devm_gpiochip_add_data_with_key" [drivers/iio/adc/rohm-bd79124.ko] undefined!
ERROR: modpost: "gpiochip_get_data" [drivers/iio/adc/rohm-bd79124.ko] undefined!
at linking phase if GPIOLIB is not configured to be used.
Fix this by adding dependency to the GPIOLIB.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202508131533.5sSkq80B-lkp@intel.com/
Fixes: 3f57a3b9ab74 ("iio: adc: Support ROHM BD79124 ADC")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/6837249bddf358924e67566293944506206d2d62.1755076369.git.mazziesaccount@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use kvfree() to fix the following Coccinelle/coccicheck warning reported
by kfree_mismatch.cocci:
WARNING kvmalloc is used to allocate this memory at line 10398
Fixes: f728c17fc97a ("accel/habanalabs/gaudi2: move HMMU page tables to device memory")
Reported-by: Qianfeng Rong <rongqianfeng@vivo.com>
Closes: https://patch.msgid.link/20250808085530.233737-1-rongqianfeng@vivo.com
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
[lukas: acknowledge Qianfeng, adjust Thorsten's domain, add Fixes tag]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Cc: stable@vger.kernel.org # v6.9+
Link: https://patch.msgid.link/20240820231028.136126-1-thorsten.blum@toblux.com
|
|
During raid resync, if a disk becomes faulty, the operation is
briefly interrupted. The MD_RECOVERY_RECOVER flag triggered by
the disk failure causes sync_action to incorrectly show "recover"
instead of "resync". The same issue affects reshape operations.
Reproduction steps:
mdadm -Cv /dev/md1 -l1 -n4 -e1.2 /dev/sd{a..d} // -> resync happened
mdadm -f /dev/md1 /dev/sda // -> resync interrupted
cat sync_action
-> recover
Add progress checks in md_sync_action() for resync/recover/reshape
to ensure the interface correctly reports the actual operation type.
Fixes: 4b10a3bc67c1 ("md: ensure resync is prioritized over recovery")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Link: https://lore.kernel.org/linux-raid/20250816002534.1754356-3-zhengqixing@huaweicloud.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
|
|
Add a helper for checking if an rdev needs recovery.
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Link: https://lore.kernel.org/linux-raid/20250816002534.1754356-2-zhengqixing@huaweicloud.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
|
|
commit 907a99c314a5 ("md: rename recovery_cp to resync_offset") replaces
recovery_cp with resync_offset in mdp_superblock_s which is in md_p.h.
md_p.h is used in userspace too. So mdadm building fails because of this.
This patch revert this change.
Fixes: 907a99c314a5 ("md: rename recovery_cp to resync_offset")
Signed-off-by: Xiao Ni <xni@redhat.com>
Link: https://lore.kernel.org/linux-raid/20250815040028.18085-1-xni@redhat.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
|
|
Pull drm fixes from Dave Airlie:
"Relatively quiet week, usual amdgpu/i915/xe fixes along with a set of
fixes for fbdev format info, which fix some regressions seen in with
rc1.
bridge:
- fix OF-node leak
- fix documentation
fbdev-emulation:
- pass correct format info to drm_helper_mode_fill_fb_struct()
panfrost:
- print correct RSS size
amdgpu:
- PSP fix
- VRAM reservation fix
- CSA fix
- Process kill fix
i915:
- Fix the implementation of wa_18038517565 [fbc]
- Do not trigger Frame Change events from frontbuffer flush [psr]
xe:
- Some more xe_migrate_access_memory fixes (Auld)
- Defer buffer object shrinker write-backs and GPU waits (Thomas)
- HWMON fix for clamping limits (Karthik)
- SRIOV-PF: Set VF LMEM BAR size (Michal)"
* tag 'drm-fixes-2025-08-16' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe/pf: Set VF LMEM BAR size
drm/amdgpu: fix task hang from failed job submission during process kill
drm/amdgpu: fix incorrect vm flags to map bo
drm/amdgpu: fix vram reservation issue
drm/amdgpu: Add PSP fw version check for fw reserve GFX command
drm/xe/hwmon: Add SW clamp for power limits writes
drm/xe: Defer buffer object shrinker write-backs and GPU waits
drm/xe/migrate: prevent potential UAF
drm/xe/migrate: don't overflow max copy size
drm/xe/migrate: prevent infinite recursion
drm/i915/psr: Do not trigger Frame Change events from frontbuffer flush
drm/i915/fbc: fix the implementation of wa_18038517565
drm/panfrost: Print RSS for tiler heap BO's in debugfs GEMS file
drm/radeon: Pass along the format info from .fb_create() to drm_helper_mode_fill_fb_struct()
drm/nouveau: Pass along the format info from .fb_create() to drm_helper_mode_fill_fb_struct()
drm/omap: Pass along the format info from .fb_create() to drm_helper_mode_fill_fb_struct()
drm/bridge: document HDMI CEC callbacks
drm/bridge: Describe the newly introduced drm_connector parameter for drm_bridge_detect
drm/bridge: fix OF node leak
|
|
In 32-bit arm, the build fails with:
error[E0308]: mismatched types
--> drivers/gpu/drm/nova/file.rs:42:28
|
42 | getparam.set_value(value);
| --------- ^^^^^ expected `u64`, found `u32`
| |
| arguments to this method are incorrect
|
note: method defined here
--> drivers/gpu/drm/nova/uapi.rs:29:12
|
29 | pub fn set_value(&self, v: u64) {
| ^^^^^^^^^ ------
help: you can convert a `u32` to a `u64`
|
42 | getparam.set_value(value.into());
| +++++++
The reason is that `Getparam::set_value` takes a `u64` (from the UAPI),
but `pci::Device::resource_len()` returns a `resource_size_t`, which is a
`phys_addr_t`, which may be 32- or 64-bit.
Thus add an `into()` call to support the 32-bit case, while allowing the
Clippy lint that complains in the 64-bit case where the type is the same.
Fixes: cdeaeb9dd762 ("drm: nova-drm: add initial driver skeleton")
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Christian Schrefl <chrisi.schrefl@gmail.com>
Link: https://lore.kernel.org/r/20250724165441.2105632-1-ojeda@kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
While trying to fill a random RSS key, the size of the pointer
is being used rather than the actual size of the RSS key.
Fix by passing an appropriate value of the RSS key.
This issue was reported by static coverity analyser.
Fixes: eb4898fde1de8 ("net: libwx: add wangxun vf common api")
Signed-off-by: Chandra Mohan Sundar <chandramohan.explore@gmail.com>
Link: https://patch.msgid.link/20250814163014.613004-1-chandramohan.explore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add formatting directive line in function `drm_gpuvm_sm_map_exec_lock()`
comment to clear warning messages shown bellow that appears generating
documentation `make htmldocs`.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2444: Unexpected indentation.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2446: Block quote ends without a blank line; unexpected unindent.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2450: Definition list ends without a blank line; unexpected unindent.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2451: Definition list ends without a blank line; unexpected unindent.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2455: Unexpected indentation.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2456: Definition list ends without a blank line; unexpected unindent.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2457: Definition list ends without a blank line; unexpected unindent.
Warning: ./drivers/gpu/drm/drm_gpuvm.c:2458: Definition list ends without a blank line; unexpected unindent.
Fixes: 471920ce25d5 ("drm/gpuvm: Add locking helpers")
Signed-off-by: Javier Garcia <rampxxxx@gmail.com>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250810150706.305040-1-rampxxxx@gmail.com
[ Fix typo in commit message. - Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
Replace kfree() with kvfree() for memory allocated by kvmalloc().
Compile-tested only.
Cc: stable@vger.kernel.org
Fixes: 8a8b1ec5261f ("drm/nouveau/gsp: split rpc handling out on its own")
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Timur Tabi <ttabi@nvidia.com>
Acked-by: Zhi Wang <zhiw@nvidia.com>
Link: https://lore.kernel.org/r/20250813125412.96178-1-rongqianfeng@vivo.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_conn: Fix running bis_cleanup for hci_conn->type PA_LINK
- hci_conn: Fix not cleaning up Broadcaster/Broadcast Source
- hci_core: Fix using {cis,bis}_capable for current settings
- hci_core: Fix using ll_privacy_capable for current settings
- hci_core: Fix not accounting for BIS/CIS/PA links separately
- hci_conn: do return error from hci_enhanced_setup_sync()
- hci_event: fix MTU for BN == 0 in CIS Established
- hci_sync: Fix scan state after PA Sync has been established
- hci_sync: Avoid adding default advertising on startup
- hci_sync: Prevent unintended PA sync when SID is 0xFF
- ISO: Fix getname not returning broadcast fields
- btmtk: Fix wait_on_bit_timeout interruption during shutdown
- btnxpuart: Uses threaded IRQ for host wakeup handling
* tag 'for-net-2025-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: hci_core: Fix not accounting for BIS/CIS/PA links separately
Bluetooth: btnxpuart: Uses threaded IRQ for host wakeup handling
Bluetooth: hci_conn: do return error from hci_enhanced_setup_sync()
Bluetooth: hci_event: fix MTU for BN == 0 in CIS Established
Bluetooth: hci_sync: Prevent unintended PA sync when SID is 0xFF
Bluetooth: hci_core: Fix using ll_privacy_capable for current settings
Bluetooth: hci_core: Fix using {cis,bis}_capable for current settings
Bluetooth: btmtk: Fix wait_on_bit_timeout interruption during shutdown
Bluetooth: hci_conn: Fix not cleaning up Broadcaster/Broadcast Source
Bluetooth: hci_conn: Fix running bis_cleanup for hci_conn->type PA_LINK
Bluetooth: ISO: Fix getname not returning broadcast fields
Bluetooth: hci_sync: Fix scan state after PA Sync has been established
Bluetooth: hci_sync: Avoid adding default advertising on startup
====================
Link: https://patch.msgid.link/20250815142229.253052-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
By default, the device does not forward IPv4 packets with a link-local
source IP (i.e., 169.254.0.0/16). This behavior does not align with the
kernel which does forward them.
Fix by instructing the device to forward such packets instead of
dropping them.
Fixes: ca360db4b825 ("mlxsw: spectrum: Disable DIP_LINK_LOCAL check in hardware pipeline")
Reported-by: Zoey Mertes <zoey@cloudflare.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/6721e6b2c96feb80269e72ce8d0b426e2f32d99c.1755174341.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull block fixes from Jens Axboe:
- Fix for unprivileged daemons in ublk
- Speedup ublk release by removing unnecessary quiesce
- Fix for blk-wbt, where a regression caused it to not be possible to
enable at runtime
- blk-wbt cleanups
- Kill the page pool from drbd
- Remove redundant __GFP_NOWARN uses in a few spots
- Fix for a kobject double initialization issues
* tag 'block-6.17-20250815' of git://git.kernel.dk/linux:
block: restore default wbt enablement
Docs: admin-guide: Correct spelling mistake
blk-wbt: doc: Update the doc of the wbt_lat_usec interface
blk-wbt: Eliminate ambiguity in the comments of struct rq_wb
blk-wbt: Optimize wbt_done() for non-throttled writes
block: fix kobject double initialization in add_disk
blk-cgroup: remove redundant __GFP_NOWARN
block, bfq: remove redundant __GFP_NOWARN
ublk: check for unprivileged daemon on each I/O fetch
ublk: don't quiesce in ublk_ch_release
drbd: Remove the open-coded page pool
|
|
Commit
7ffeb2fc2670 ("x86/sev: Document requirement for linear mapping of guest request buffers")
added a check that requires the guest request buffers to be in the linear
mapping. The get_derived_key() function was passing a buffer that was
allocated on the stack, resulting in the call to snp_send_guest_request()
returning an error.
Update the get_derived_key() function to use an allocated buffer instead
of a stack buffer.
Fixes: 7ffeb2fc2670 ("x86/sev: Document requirement for linear mapping of guest request buffers")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/9b764ca9fc79199a091aac684c4926e2080ca7a8.1752698495.git.thomas.lendacky@amd.com
|
|
This replaces devm_request_irq() with devm_request_threaded_irq().
On iMX93 11x11 EVK platform, the BT chip's BT_WAKE_OUT pin is connected
to an I2C GPIO expander instead of directly been connected to iMX GPIO.
When I2C GPIO expander's (PCAL6524) host driver receives an interrupt on
it's INTR line, the driver's interrupt handler needs to query the
interrupt source with PCAL6524 first, and then call the actual interrupt
handler, in this case the IRQ handler in BTNXPUART.
In order to handle interrupts when such I2C GPIO expanders are between
the host and interrupt source, devm_request_threaded_irq() is needed.
This commit also removes the IRQF_TRIGGER_FALLING flag, to allow setting
the IRQ trigger type from the device tree setting instead of hardcoding
in the driver.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix the way optional interrupts are retrieved from firmware in
gpio-mlxbf3
* tag 'gpio-fixes-for-v6.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: mlxbf3: use platform_get_irq_optional()
Revert "gpio: mlxbf3: only get IRQ for device instance 0"
|
|
During the shutdown process, an interrupt occurs that
prematurely terminates the wait for the expected event.
This change replaces TASK_INTERRUPTIBLE with
TASK_UNINTERRUPTIBLE in the wait_on_bit_timeout call to ensure
the shutdown process completes as intended without being
interrupted by signals.
Fixes: d019930b0049 ("Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.c")
Signed-off-by: Jiande Lu <jiande.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fix from Ulf Hansson:
- tegra: Ensure pmc power-domains are in a known state
* tag 'pmdomain-v6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
soc/tegra: pmc: Ensure power-domains are in a known state
|
|
Sparse reported a warning:
drivers/iommu/arm/arm-smmu-v3/tegra241-cmdqv.c:305:47:
sparse: expected restricted __le64
sparse: got unsigned long long
Add cpu_to_le64() to fix that.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202508142105.Jb5Smjsg-lkp@intel.com/
Suggested-by: Pranjal Shrivastava <praan@google.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/r/20250814193039.2265813-1-nicolinc@nvidia.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
While the kernel command line is considered trusted in most environments,
avoid writing 1 byte past the end of "acpiid" if the "str" argument is
maximum length.
Reported-by: Simcha Kosman <simcha.kosman@cyberark.com>
Closes: https://lore.kernel.org/all/AS8P193MB2271C4B24BCEDA31830F37AE84A52@AS8P193MB2271.EURP193.PROD.OUTLOOK.COM
Fixes: b6b26d86c61c ("iommu/amd: Add a length limitation for the ivrs_acpihid command-line parameter")
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Ankit Soni <Ankit.Soni@amd.com>
Link: https://lore.kernel.org/r/20250804154023.work.970-kees@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
The qla4xxx_get_ep_fwdb() function is supposed to return NULL on error,
but qla4xxx_ep_connect() returns error pointers. Propagating the error
pointers will lead to an Oops in the caller, so change the error pointers
to NULL.
Fixes: 13483730a13b ("[SCSI] qla4xxx: fix flash/ddb support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/aJwnVKS9tHsw1tEu@stanley.mountain
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add PCI ID to support Intel Wildcat Lake, same as MTL.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250812130259.109645-1-adrian.hunter@intel.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
devm_drm_bridge_alloc() returns ERR_PTR on failure instead of a
NULL pointer, so use IS_ERR() to check the returned pointer.
While at it, on failure, return ERR_CAST(dp) instead of
ERR_PTR(-ENOMEM) in order not to depend on devm_drm_bridge_alloc()
error code implementation.
Fixes: 48f05c3b4b70 ("drm/bridge: analogix_dp: Use devm_drm_bridge_alloc() API")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20250806095224.527938-1-victor.liu@nxp.com
|
|
struct mempool doesn't currently exist, and thus also isn't used in
fnic.h, remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250812082808.371119-1-hch@lst.de
Reviewed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixes from Takashi Sakamoto:
"This fixes a potential call to schedule() within an RCU read-side
critical section. The solution applies reference counting to ensure
that handlers which may call schedule() are invoked safely outside of
the critical section"
* tag 'firewire-fixes-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: core: reallocate buffer for FCP address handlers when more than 4 are registered
firewire: core: call FCP address handlers outside RCU read-side critical section
firewire: core: call handler for exclusive regions outside RCU read-side critical section
firewire: core: use reference counting to invoke address handlers safely
|
|
The CRC error bit is located at bit 17 in the Rx descriptor, but the
driver was incorrectly using bit 16. Fix it.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20250813071631.7566-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Submit multiple descriptors in axienet_rx_cb() to fill Rx skb ring. This
ensures the ring "catches up" on previously missed allocations.
Increment Rx skb ring head pointer after BD is successfully allocated.
Previously, head pointer was incremented before verifying if descriptor is
successfully allocated and has valid entries, which could lead to ring
state inconsistency if descriptor setup failed.
These changes improve reliability by maintaining adequate descriptor
availability and ensuring proper ring buffer state management.
Fixes: 6a91b846af85 ("net: axienet: Introduce dmaengine support")
Signed-off-by: Suraj Gupta <suraj.gupta2@amd.com>
Link: https://patch.msgid.link/20250813135559.1555652-1-suraj.gupta2@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
- Some more xe_migrate_access_memory fixes (Auld)
- Defer buffer object shrinker write-backs and GPU waits (Thomas)
- HWMON fix for clamping limits (Karthik)
- SRIOV-PF: Set VF LMEM BAR size (Michal)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/aJ4MIZQurSo0uNxn@intel.com
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes
- Fix the implementation of wa_18038517565 [fbc] (Vinod Govindapillai)
- Do not trigger Frame Change events from frontbuffer flush [psr] (Jouni Högander)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tursulin@igalia.com>
Link: https://lore.kernel.org/r/aJ0HAh06VHWVdv63@linux
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These restore corner case behavior of the EC driver related to the
handling of defective ACPI tables and fix a recent regression in the
ACPI processor driver:
- Prevent the ACPI EC driver from ignoring ECDT information in the
cases when the ID string in the ECDT is invalid, but not empty, to
fix thouchpad detection on ThinkBook 14 G7 IML (Armin Wolf)
- Rearrange checks in acpi_processor_ppc_init() to restore the
handling of frequency QoS requests related to _PPC limits
inadvertently broken by a recent update (Rafael Wysocki)"
* tag 'acpi-6.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: EC: Relax sanity check of the ECDT ID string
ACPI: processor: perflib: Move problematic pr->performance check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These remove an artificial limitation from the intel_idle driver,
update the menu cpuidle governor to restore its previous behavior in a
corner case and add one more supported platform configuration to the
intel_pstate driver:
- Allow intel_idle to use _CST information from ACPI tables for idle
states enumeration on any family of processors (Len Brown)
- Restore corner case behavior of the menu cpuidle governor, related
to the handling of systems where idle states selected by the
governor are rejected by the cpuidle driver, inadvertently changed
during the 6.15 development cycle (Rafael Wysocki)
- Add support for Clearwater Forest in the out-of-band (OOB) mode to
the intel_pstate driver (Srinivas Pandruvada)"
* tag 'pm-6.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Support Clearwater Forest OOB mode
cpuidle: governors: menu: Avoid using invalid recent intervals data
intel_idle: Allow loading ACPI tables for any family
|
|
LMEM is partitioned between multiple VFs and we expect that the more
VFs we have, the less LMEM is assigned to each VF.
This means that we can achieve full LMEM BAR access without the need to
attempt full VF LMEM BAR resize via pci_resize_resource().
Always try to set the largest possible BAR size that allows to fit the
number of enabled VFs and inform the user in case the resize attempt is
not successful.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250527120637.665506-7-michal.winiarski@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 32a4d1b98e6663101fd0abfaf151c48feea7abb1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from Netfilter and IPsec.
Current release - regressions:
- netfilter: nft_set_pipapo:
- don't return bogus extension pointer
- fix null deref for empty set
Current release - new code bugs:
- core: prevent deadlocks when enabling NAPIs with mixed kthread
config
- eth: netdevsim: Fix wild pointer access in nsim_queue_free().
Previous releases - regressions:
- page_pool: allow enabling recycling late, fix false positive
warning
- sched: ets: use old 'nbands' while purging unused classes
- xfrm:
- restore GSO for SW crypto
- bring back device check in validate_xmit_xfrm
- tls: handle data disappearing from under the TLS ULP
- ptp: prevent possible ABBA deadlock in ptp_clock_freerun()
- eth:
- bnxt: fill data page pool with frags if PAGE_SIZE > BNXT_RX_PAGE_SIZE
- hv_netvsc: fix panic during namespace deletion with VF
Previous releases - always broken:
- netfilter: fix refcount leak on table dump
- vsock: do not allow binding to VMADDR_PORT_ANY
- sctp: linearize cloned gso packets in sctp_rcv
- eth:
- hibmcge: fix the division by zero issue
- microchip: fix KSZ8863 reset problem"
* tag 'net-6.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
net: usb: asix_devices: add phy_mask for ax88772 mdio bus
net: kcm: Fix race condition in kcm_unattach()
selftests: net/forwarding: test purge of active DWRR classes
net/sched: ets: use old 'nbands' while purging unused classes
bnxt: fill data page pool with frags if PAGE_SIZE > BNXT_RX_PAGE_SIZE
netdevsim: Fix wild pointer access in nsim_queue_free().
net: mctp: Fix bad kfree_skb in bind lookup test
netfilter: nf_tables: reject duplicate device on updates
ipvs: Fix estimator kthreads preferred affinity
netfilter: nft_set_pipapo: fix null deref for empty set
selftests: tls: test TCP stealing data from under the TLS socket
tls: handle data disappearing from under the TLS ULP
ptp: prevent possible ABBA deadlock in ptp_clock_freerun()
ixgbe: prevent from unwanted interface name changes
devlink: let driver opt out of automatic phys_port_name generation
net: prevent deadlocks when enabling NAPIs with mixed kthread config
net: update NAPI threaded config even for disabled NAPIs
selftests: drv-net: don't assume device has only 2 queues
docs: Fix name for net.ipv4.udp_child_hash_entries
riscv: dts: thead: Add APB clocks for TH1520 GMACs
...
|
|
* acpi-ec:
ACPI: EC: Relax sanity check of the ECDT ID string
* acpi-processor:
ACPI: processor: perflib: Move problematic pr->performance check
|
|
* pm-cpuidle:
cpuidle: governors: menu: Avoid using invalid recent intervals data
intel_idle: Allow loading ACPI tables for any family
* pm-cpufreq:
cpufreq: intel_pstate: Support Clearwater Forest OOB mode
|
|
Delete extra checks for the ATA_DFLAG_CDL_ENABLED flag that prevent
SET FEATURES command from being issued to a drive when NCQ commands
are active.
ata_mselect_control_ata_feature() sets / clears the ATA_DFLAG_CDL_ENABLED
flag during the translation of MODE SELECT to SET FEATURES. If SET FEATURES
gets deferred due to outstanding NCQ commands, the original MODE SELECT
command will be re-queued. When the re-queued MODE SELECT goes through
the ata_mselect_control_ata_feature() translation again, SET FEATURES
will not be issued because ATA_DFLAG_CDL_ENABLED has been already set or
cleared by the initial translation of MODE SELECT.
The ATA_DFLAG_CDL_ENABLED checks in ata_mselect_control_ata_feature()
are safe to remove because scsi_cdl_enable() implements a similar logic
that avoids enabling CDL if it has been enabled already.
Fixes: 17e897a45675 ("ata: libata-scsi: Improve CDL control")
Cc: stable@vger.kernel.org
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Make video port registers nonvolatile. As DSP_CTRL register is written
to twice due to gamma LUT enable bit which is set outside of the main
DSP_CTRL initialization within atomic_enable (for rk356x case it is also
necessary to always disable gamma LUT before writing a new LUT) there is
a chance that DSP_CTRL value read-out in gamma LUT init/update code is
not the one which was written by the preceding DSP_CTRL initialization
code within atomic_enable. This might result in misconfigured DSP_CTRL
which leads to no visual output[1]. Since DSP_CTRL write takes effect
after VSYNC[1] the issue is not always present. When tested on Pinetab2
with kernel 6.14 it happenes only when DRM is compiled as a module[1].
In order to confirm that it is a timing issue I inserted 18ms udelay
before vop2_crtc_atomic_try_set_gamma in atomic enable and compiled DRM
as module - this has also fixed the issue.
[1] https://lore.kernel.org/linux-rockchip/562b38e5.a496.1975f09f983.Coremail.andyshrk@163.com/
Reported-by: Diederik de Haas <didi.debian@cknow.org>
Closes: https://lore.kernel.org/linux-rockchip/DAEVDSTMWI1E.J454VZN0R9MA@cknow.org/
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Piotr Zalewski <pZ010001011111@proton.me>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250706083629.140332-2-pZ010001011111@proton.me
|
|
Select drm bridge connector when building cdp-dp.
This was missed in previous commit causing build failure.
Fixes: afbbca25d06e ("drm/rockchip: cdn-dp: Convert to drm bridge")
Signed-off-by: Rudi Heitbaum <rudi@heitbaum.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/aJrlUzV1u4i65NRe@8eba3d7b3083
|
|
Commit 4371fe1ba400 ("ata: libata-eh: Avoid unnecessary resets when
revalidating devices") replaced the call to ata_phys_link_offline() in
ata_eh_revalidate_and_attach() with the new function
ata_eh_link_established() which relaxes the checks on a device link
state to account for low power mode transitions. However, this change
assumed that the device port has a valid scr_read method to obtain the
SStatus register for the port. This is not always the case, especially
with older IDE/PATA adapters (e.g. PATA/IDE devices emulated with QEMU).
For such adapter, ata_eh_link_established() will always return false,
causing ata_eh_revalidate_and_attach() to go into its error path and
ultimately to the device being disabled.
Avoid this by restoring the previous behavior, which is to assume that
the link is online if reading the port SStatus register fails.
While at it, also fix the spelling of SStatus in the comment describing
the function ata_eh_link_established().
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 4371fe1ba400 ("ata: libata-eh: Avoid unnecessary resets when revalidating devices")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Without setting phy_mask for ax88772 mdio bus, current driver may create
at most 32 mdio phy devices with phy address range from 0x00 ~ 0x1f.
DLink DUB-E100 H/W Ver B1 is such a device. However, only one main phy
device will bind to net phy driver. This is creating issue during system
suspend/resume since phy_polling_mode() in phy_state_machine() will
directly deference member of phydev->drv for non-main phy devices. Then
NULL pointer dereference issue will occur. Due to only external phy or
internal phy is necessary, add phy_mask for ax88772 mdio bus to workarnoud
the issue.
Closes: https://lore.kernel.org/netdev/20250806082931.3289134-1-xu.yang_2@nxp.com
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250811092931.860333-1-xu.yang_2@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
ixgbe: bypass devlink phys_port_name generation
Jedrzej adds option to skip phys_port_name generation and opts
ixgbe into it as some configurations rely on pre-devlink naming
which could end up broken as a result.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ixgbe: prevent from unwanted interface name changes
devlink: let driver opt out of automatic phys_port_name generation
====================
Link: https://patch.msgid.link/20250812205226.1984369-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The data page pool always fills the HW rx ring with pages. On arm64 with
64K pages, this will waste _at least_ 32K of memory per entry in the rx
ring.
Fix by fragmenting the pages if PAGE_SIZE > BNXT_RX_PAGE_SIZE. This
makes the data page pool the same as the header pool.
Tested with iperf3 with a small (64 entries) rx ring to encourage buffer
circulation.
Fixes: cd1fafe7da1f ("eth: bnxt: add support rx side device memory TCP")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250812182907.1540755-1-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported the splat below. [0]
When nsim_queue_uninit() is called from nsim_init_netdevsim(),
register_netdevice() has not been called, thus dev->dstats has
not been allocated.
Let's not call dev_dstats_rx_dropped_add() in such a case.
[0]
BUG: unable to handle page fault for address: ffff88809782c020
PF: supervisor write access in kernel mode
PF: error_code(0x0002) - not-present page
PGD 1b401067 P4D 1b401067 PUD 0
Oops: Oops: 0002 [#1] SMP KASAN NOPTI
CPU: 3 UID: 0 PID: 8476 Comm: syz.1.251 Not tainted 6.16.0-syzkaller-06699-ge8d780dcd957 #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:local_add arch/x86/include/asm/local.h:33 [inline]
RIP: 0010:u64_stats_add include/linux/u64_stats_sync.h:89 [inline]
RIP: 0010:dev_dstats_rx_dropped_add include/linux/netdevice.h:3027 [inline]
RIP: 0010:nsim_queue_free+0xba/0x120 drivers/net/netdevsim/netdev.c:714
Code: 07 77 6c 4a 8d 3c ed 20 7e f1 8d 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 75 46 4a 03 1c ed 20 7e f1 8d <4c> 01 63 20 be 00 02 00 00 48 8d 3d 00 00 00 00 e8 61 2f 58 fa 48
RSP: 0018:ffffc900044af150 EFLAGS: 00010286
RAX: dffffc0000000000 RBX: ffff88809782c000 RCX: 00000000000079c3
RDX: 1ffffffff1be2fc7 RSI: ffffffff8c15f380 RDI: ffffffff8df17e38
RBP: ffff88805f59d000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000003 R14: ffff88806ceb3d00 R15: ffffed100dfd308e
FS: 0000000000000000(0000) GS:ffff88809782c000(0063) knlGS:00000000f505db40
CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: ffff88809782c020 CR3: 000000006fc6a000 CR4: 0000000000352ef0
Call Trace:
<TASK>
nsim_queue_uninit drivers/net/netdevsim/netdev.c:993 [inline]
nsim_init_netdevsim drivers/net/netdevsim/netdev.c:1049 [inline]
nsim_create+0xd0a/0x1260 drivers/net/netdevsim/netdev.c:1101
__nsim_dev_port_add+0x435/0x7d0 drivers/net/netdevsim/dev.c:1438
nsim_dev_port_add_all drivers/net/netdevsim/dev.c:1494 [inline]
nsim_dev_reload_create drivers/net/netdevsim/dev.c:1546 [inline]
nsim_dev_reload_up+0x5b8/0x860 drivers/net/netdevsim/dev.c:1003
devlink_reload+0x322/0x7c0 net/devlink/dev.c:474
devlink_nl_reload_doit+0xe31/0x1410 net/devlink/dev.c:584
genl_family_rcv_msg_doit+0x206/0x2f0 net/netlink/genetlink.c:1115
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0x55c/0x800 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x155/0x420 net/netlink/af_netlink.c:2552
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1320 [inline]
netlink_unicast+0x5aa/0x870 net/netlink/af_netlink.c:1346
netlink_sendmsg+0x8d1/0xdd0 net/netlink/af_netlink.c:1896
sock_sendmsg_nosec net/socket.c:714 [inline]
__sock_sendmsg net/socket.c:729 [inline]
____sys_sendmsg+0xa95/0xc70 net/socket.c:2614
___sys_sendmsg+0x134/0x1d0 net/socket.c:2668
__sys_sendmsg+0x16d/0x220 net/socket.c:2700
do_syscall_32_irqs_on arch/x86/entry/syscall_32.c:83 [inline]
__do_fast_syscall_32+0x7c/0x3a0 arch/x86/entry/syscall_32.c:306
do_fast_syscall_32+0x32/0x80 arch/x86/entry/syscall_32.c:331
entry_SYSENTER_compat_after_hwframe+0x84/0x8e
RIP: 0023:0xf708e579
Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d b4 26 00 00 00 00 8d b4 26 00 00 00 00
RSP: 002b:00000000f505d55c EFLAGS: 00000296 ORIG_RAX: 0000000000000172
RAX: ffffffffffffffda RBX: 0000000000000007 RCX: 0000000080000080
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000296 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Modules linked in:
CR2: ffff88809782c020
Fixes: 2a68a22304f9 ("netdevsim: account dropped packet length in stats on queue free")
Reported-by: syzbot+8aa80c6232008f7b957d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/688bb9ca.a00a0220.26d0e1.0050.GAE@google.com/
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250812162130.4129322-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.17-2025-08-13:
amdgpu:
- PSP fix
- VRAM reservation fix
- CSA fix
- Process kill fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250813151905.2040816-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
Short summary of fixes pull:
bridge:
- fix OF-node leak
- fix documentation
fbdev-emulation:
- pass correct format info to drm_helper_mode_fill_fb_struct()
panfrost:
- print correct RSS size
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250812064712.GA14554@2a02-2454-fd5e-fd00-2c49-c639-c55f-a125.dyn6.pyur.net
|
|
Since 'bcs->Residue' has the data type '__le32', convert it to the
correct byte order of the CPU using this driver when assigning it to
the local variable 'residue'.
Cc: stable <stable@kernel.org>
Fixes: 50a6cb932d5c ("USB: usb_storage: add ums-realtek driver")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20250813145247.184717-3-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
