| Age | Commit message (Collapse) | Author |
|---|
|
None of the headers are included from outside of the mach-pxa
directory, so move them all in there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a support for ADS7846 touchscreen driver.
The basic functionality was tested, x_plate_ohms and y_plate_ohms were
physically measured. The value pressure_max was empirically set to match
the measured range, which is affected by x_plate_ohms and ADS samples.
The value of keep_vref_on should be set. A tested model (T-Mobile MDA
Compact PM10A) doesn't seem to use Vref pin as the input from an external
source. On this model the unset keep_vref_on cause high jitter of measured
values.
SPI framing pin (gpio_cs) must be used in GPIO mode due to an incompatible
autoframing of PXA27x controller and ADS7846 device.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This patch renames EGPIOs, which are used for the charging cable presence
and type detection. Old names did not correspond with an observed
functionality (on board_id 0x3a). The behavior is not:
- AC charger
- USB charger
- Cable detection
, but:
- AC/USB type
- Cable detection1
- Cable detection2
This patch fixes a possible typo in the bit offset for the cable detection
EGPIO declaration, too.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This patch renames GPIOs, which are used to control the power lines to
the LCD screen. New names correspond to a real functionality, which was
measured on the HTC Magician board_id 0x3a.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This patch adds EGPIO pins: Infra transceiver power, NiCD charging and
inserted charger cable.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This patch fixes the indentation for the HTC Magician machine definition.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
NR_BUILTIN_GPIO is both defined in arch-pxa and arch-mmp. Now replace it
with PXA_NR_BUILTIN_GPIO and MMP_NR_BUILTIN_GPIO.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
|
|
Commit "ARM: pxa: align NR_BUILTIN_GPIO with GPIO interrupt number"
increased NR_BUILTIN_GPIO from 128 to PXA_GPIO_IRQ_NUM (192).
Adjust the previously hardcoded MAGICIAN_EGPIO_BASE accordingly.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
With this patch, the bq24022 battery charger is controlled by the USB
gadget framework (via gpio_vbus) when connected to USB.
To compile, this patch depends on the "regulator: Allow init data to be
supplied for bq24022" patch (queued for next in the regulator tree) to
add the init_data field to struct bq24022_mach_info.
It also depends on the "add optional OTG transceiver and voltage
regulator support to pda_power" patch (queued for next in the power
supply tree) to enable charging when connected to the AC charger.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
This patch depends on otg_transceiver support in pxa27x_udc
(which is queued via linux-usb) to work.
It compiles also without it.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
