| Age | Commit message (Collapse) | Author |
|---|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There are 11 newly supported SoCs, but these are all either new
variants of existing designs, or straight reuses of the existing chip
in a new package:
- RK3562 is a new chip based on the old Cortex-A53 core, apparently a
low-cost version of the Cortex-A55 based RK3568/RK3566.
- NXP i.MX94 is a minor variation of i.MX93/i.MX95 with a different
set of on-chip peripherals.
- Renesas RZ/V2N (R9A09G056) is a new member of the larger RZ/V2
family
- Amlogic S6/S7/S7D
- Samsung Exynos7870 is an older chip similar to Exynos7885
- WonderMedia wm8950 is a minor variation on the wm8850 chip
- Amlogic s805y is almost idential to s805x
- Allwinner A523 is similar to A527 and T527
- Qualcomm MSM8926 is a variant of MSM8226
- Qualcomm Snapdragon X1P42100 is related to R1E80100
There are also 65 boards, including reference designs for the chips
above, this includes
- 12 new boards based on TI K3 series chips, most of them from
Toradex
- 10 devices using Rockchips RK35xx and PX30 chips
- 2 phones and 2 laptops based on Qualcomm Snapdragon designs
- 10 NXP i.MX8/i.MX9 boards, mostly for embedded/industrial uses
- 3 Samsung Galaxy phones based on Exynos7870
- 5 Allwinner based boards using a variety of ARMv8 chips
- 9 32-bit machines, each based on a different SoC family
Aside from the new hardware, there is the usual set of cleanups and
newly added hardware support on existing machines, for a total of 965
devicetree changesets"
* tag 'soc-dt-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (956 commits)
MAINTAINERS, mailmap: update Sven Peter's email address
arm64: dts: renesas: rzg3e-smarc-som: Reduce I2C2 clock frequency
arm64: dts: nuvoton: Add pinctrl
ARM: dts: samsung: sp5v210-aries: Align wifi node name with bindings
arm64: dts: blaize-blzp1600: Enable GPIO support
dt-bindings: clock: socfpga: convert to yaml
arm64: dts: rockchip: move rk3562 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3562 pcie unit addresses
arm64: dts: rockchip: move rk3528 pinctrl node outside the soc node
arm64: dts: rockchip: remove a double-empty line from rk3576 core dtsi
arm64: dts: rockchip: move rk3576 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3576 pcie unit addresses
arm64: dts: rockchip: Drop assigned-clock* from cpu nodes on rk3588
arm64: dts: rockchip: Add missing SFC power-domains to rk3576
Revert "arm64: dts: mediatek: mt8390-genio-common: Add firmware-name for scp0"
arm64: dts: mediatek: mt8188: Address binding warnings for MDP3 nodes
arm64: dts: mt6359: Rename RTC node to match binding expectations
arm64: dts: mt8365-evk: Add goodix touchscreen support
arm64: dts: mediatek: mt8188: Add missing #reset-cells property
arm64: dts: airoha: en7581: Add PCIe nodes to EN7581 SoC evaluation board
...
|
|
Some boards have noise on the UART RX line when the UART pins are not
connected to another device (such as an USB UART adapter). This can
be addressed by using a pull up resistor. Not all boards may provide
such a pull up resistor on the PCB so enable the SoC's pull-up on the
UART RX and TX pads by default. This matches the default (from u-boot
or SoC hardware) state for the pinmux configuration on these pads.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250329185855.854186-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Device-tree expects absent clocks to be specified as <0> (instead of
using <>). This fixes using the FCLK4/FCLK3 clocks as they are now
seen at their correct index (while before they were recognized, but at
the correct index - resulting in the hardware using a different clock
than what the kernel sees).
Fixes: a526eeef9a81 ("arm64: dts: amlogic: gx: switch to the new PWM controller binding")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250420164801.330505-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Use the new PWM controller binding which now relies on passing all
clock inputs available on the SoC (instead of passing the "wanted"
clock input for a given board).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241227212514.1376682-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
HDMI Tx needs the system clock set on the xtal rate.
This clock is managed by the main clock controller of the related SoCs.
Currently 2 part of the display drivers race to setup the HDMI system
clock by directly poking the controller register. The clock API should
be used to setup the rate instead.
Use assigned-clock to setup the HDMI system clock.
Fixes: 6939db7e0dbf ("ARM64: dts: meson-gx: Add support for HDMI output")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240626152733.1350376-3-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
The clocks provided to HDMI tx are not consistent between gx and g12:
* gx receives the peripheral clock as 'isfr' while g12 receives it as
'iahb'
* g12 gets the HDMI system clock as 'isfr' but gx does not even get it.
It surely needs that clock since the driver is directly poking around
the clock controller's registers for that clock.
Align gx SoCs with g12 and provide:
* the HDMI peripheral clock as 'iahb'
* the HDMI system clock as 'isfr'
Fixes: 6939db7e0dbf ("ARM64: dts: meson-gx: Add support for HDMI output")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240626152733.1350376-2-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
HDMI Tx needs HDMI Tx memory power domain turned on. This power domain is
handled under the VPU power domain.
The HDMI Tx currently works because it is enabling the PD by directly
poking the power controller register. It is should not do that but properly
use the power domain controller.
Fix this by adding the power domain to HDMI Tx.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240625145017.1003346-3-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
During review of a new yaml binding, affecting these dts, it turned out
that some compatibles aren't ordered as they should be. Order should be
most specific to least specific.
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/1ce888df-6096-73de-a98a-354d086428d4@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Add SPICC Controller pin nodes for CLK line when idle for Amlogic GXBB
SoCs.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221004-up-aml-fix-spi-v4-4-0342d8e10c49@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Add the OPP table for the Mali-450 GPU and drop the hardcoded initial
clock configuration. This enables GPU DVFS and thus saves power when the
GPU is not in use while still being able switch to a higher clock on
demand.
Set the GP0_PLL clock to 744MHz (which is the only frequency which
cannot be derived from the FCLK dividers) as the clock driver avoids
setting the parent clock rates so the MPLL clocks aren't changed (as
these are reserved for audio). The only exception to this is the GXL
S805X package because the 744MHz OPP isn't working correctly there.
While here, make most of meson-gxl-mali re-usable to reduce the amount
of duplicate code between GXBB and GXL. This is more important now as we
don't want to duplicate the GPU OPP table.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200719173213.639540-2-martin.blumenstingl@googlemail.com
|
|
Add the "timing-adjustment" clock now that we know how it is connected
to the PRG_ETHERNET registers. It is used internally to generate the
RGMII RX delay on the MAC side (if needed).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620162347.26159-1-martin.blumenstingl@googlemail.com
|
|
The "amlogic,meson-gx-pwrc-vpu" binding only supports the VPU power
domain, while actually there are more power domains behind that set of
registers. Switch to the new bindings so we can add more power domains
as needed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161211.23685-1-martin.blumenstingl@googlemail.com
|
|
Add the AIU audio device to the Amlogic GX SoC family DT.
ATM, this device provides the i2s and spdif output stages and also
the hdmi and internal codec glues.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20200421163935.775935-3-jbrunet@baylibre.com
|
|
This enables the video decoder for GXBB, GXL and GXM chips
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Clk pin does not require bias, data strobe should be pulled low.
The rest of the pin (data and cmd) are pulled up.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
SimpleFB allows transferring a framebuffer from the firmware/bootloader
to the kernel, while making sure the related clocks and power supplies
stay enabled.
Add nodes for CVBS and HDMI Simple Framebuffers.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the clock inputs of the clock controllers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
On Amlogic chipsets, the bias set through pinconf applies to the pad
itself, not only the GPIO function. This means that even when we change
the function of the pad from GPIO to anything else, the bias previously
set still applies.
As we have seen with the eMMC, depending on the bias type and the function,
it may trigger problems.
The underlying issue is that we inherit whatever was left by previous user
of the pad (pinconf, u-boot or the ROM code). As a consequence, the actual
setup we will get is undefined.
There is nothing mentioned in the documentation about pad bias and pinmux
function, however leaving it undefined is not an option.
This change consistently disable the pad bias for every pinmux functions.
It seems to work well, we can only assume that the necessary bias (if any)
is already provided by the pin function itself.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
In some cases (such as a boot from SPI) the bootloader or the ROM code may
leave a bias pull-down on the mmc pins. If so the MMC will fail during the
initialisation.
Explicitly disabling the pinmux solves the problem.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
In the pinmux of the mmc clk_gate nodes, we define 2 subnodes. One for
the function definition, the other for the bias. This is not necessary
since we can define the function and the bias in the same subnode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the required peripheral clock for the efuse device.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
dtc has new checks for SPI buses. The meson dts files have a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dtb: Warning (spi_bus_bridge): /soc/periphs@c8834000/pinctrl@4b0/spi: incorrect #address-cells for SPI bus
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
>From the hardware perspective, the actual pclk of the AO uarts
is the corresponding clkc_ao uart gate, not the main clock controller clk81.
This was not problem so far, because the uart_gate had
the CLK_IGNORE_UNUSED flag, which kept the gate open.
We plan to remove the CLK_IGNORE_UNUSED flag in another patch,
but before doing that, we need to fix the clock in the DTS file.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add reset lines to the mmc controllers of the meson gx and axg SoCs
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The parent of the meson-gx clock controller should be the hhi system
controller, not the HIU bus. This way, the HHI register region can be
used safely by multiple drivers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.
Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.16" from Kevin Hilman
- meson-gx: add VPU power domain support
- odroid-c2: add HDMI and CEC nodes
- misc cleanups
* tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxm: fix q200 interrupt number
ARM64: dts: meson-gxm: add the PHY interrupt line on Khadas VIM2
ARM64: dts: meson: add comments with the GPIO for the PHY interrupts
ARM64: dts: amlogic: use generic bus node names
ARM64: dts: meson: drop "sana" clock from SAR ADC
ARM64: dts: odroid-c2: Add HDMI and CEC Nodes
ARM64: dts: meson-gx: grow reset controller memory zone
ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards
ARM64: dts: meson-gx: add VPU power domain
|
|
The clock-names for pclk was wrongly set to "core", but the bindings
specifies "pclk".
This was not cathed until the legacy non-documented bindings were removed.
Reported-by: Andreas Färber <afaerber@suse.de>
Fixes: f72d6f6037b7 ("ARM64: dts: meson-gx: use stable UART bindings with correct gate clock")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The SAR ADC modules doesn't require The "sana" clock.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Singed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds support for the VPU Power Domain nodes, and attaches the
VPU power domain to the VPU node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add gpio interrupt controller to Amlogic GX family SoCs
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
TEST_N has moved from the EE controller to the AO controller so
the gpio-ranges need to adjusted for it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Remove pin offset on the EE controller. Meson pinctrl no longer has
this quirk
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Now that the clock source 0 is properly described in the CCF, use it
instead of assuming the default value (xtal)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The AO clkc needs to be updated to new bindings with an system control parent
node and moving the clkc node as subnode.
Also adds the SoC specific compatible following the bindings requirements.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch switches to the stable UART bindings but also add the correct
gate clock to the non-AO UART nodes for GXBB and GXL SoCs.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add nodes for the SPICC controller on GX common dtsi, GXBB and
GXL dtsi files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds the SPICC Controller pins nodes for Amlogic GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the AO and EE domain CEC pins nodes for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The pull-enable register base was wrongly copied from the meson8b pinctrl node,
but was not used yet.
Fixes: c328666d58aa ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Sort nodes referenced by label alphabetically.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
|
|
Add HDMI output and connector nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add EE and AO domains pins for the spdif output to the gxbb device tree.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add EE and AO domains pins for the i2s output clocks and data to the gxbb
device tree.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
