| Age | Commit message (Collapse) | Author |
|---|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There are 11 newly supported SoCs, but these are all either new
variants of existing designs, or straight reuses of the existing chip
in a new package:
- RK3562 is a new chip based on the old Cortex-A53 core, apparently a
low-cost version of the Cortex-A55 based RK3568/RK3566.
- NXP i.MX94 is a minor variation of i.MX93/i.MX95 with a different
set of on-chip peripherals.
- Renesas RZ/V2N (R9A09G056) is a new member of the larger RZ/V2
family
- Amlogic S6/S7/S7D
- Samsung Exynos7870 is an older chip similar to Exynos7885
- WonderMedia wm8950 is a minor variation on the wm8850 chip
- Amlogic s805y is almost idential to s805x
- Allwinner A523 is similar to A527 and T527
- Qualcomm MSM8926 is a variant of MSM8226
- Qualcomm Snapdragon X1P42100 is related to R1E80100
There are also 65 boards, including reference designs for the chips
above, this includes
- 12 new boards based on TI K3 series chips, most of them from
Toradex
- 10 devices using Rockchips RK35xx and PX30 chips
- 2 phones and 2 laptops based on Qualcomm Snapdragon designs
- 10 NXP i.MX8/i.MX9 boards, mostly for embedded/industrial uses
- 3 Samsung Galaxy phones based on Exynos7870
- 5 Allwinner based boards using a variety of ARMv8 chips
- 9 32-bit machines, each based on a different SoC family
Aside from the new hardware, there is the usual set of cleanups and
newly added hardware support on existing machines, for a total of 965
devicetree changesets"
* tag 'soc-dt-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (956 commits)
MAINTAINERS, mailmap: update Sven Peter's email address
arm64: dts: renesas: rzg3e-smarc-som: Reduce I2C2 clock frequency
arm64: dts: nuvoton: Add pinctrl
ARM: dts: samsung: sp5v210-aries: Align wifi node name with bindings
arm64: dts: blaize-blzp1600: Enable GPIO support
dt-bindings: clock: socfpga: convert to yaml
arm64: dts: rockchip: move rk3562 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3562 pcie unit addresses
arm64: dts: rockchip: move rk3528 pinctrl node outside the soc node
arm64: dts: rockchip: remove a double-empty line from rk3576 core dtsi
arm64: dts: rockchip: move rk3576 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3576 pcie unit addresses
arm64: dts: rockchip: Drop assigned-clock* from cpu nodes on rk3588
arm64: dts: rockchip: Add missing SFC power-domains to rk3576
Revert "arm64: dts: mediatek: mt8390-genio-common: Add firmware-name for scp0"
arm64: dts: mediatek: mt8188: Address binding warnings for MDP3 nodes
arm64: dts: mt6359: Rename RTC node to match binding expectations
arm64: dts: mt8365-evk: Add goodix touchscreen support
arm64: dts: mediatek: mt8188: Add missing #reset-cells property
arm64: dts: airoha: en7581: Add PCIe nodes to EN7581 SoC evaluation board
...
|
|
GXL I2C pins need internal pull-up enabled to operate if there
is no external resistor. The pull-up is 60kohms per the datasheet.
We should set the bias when i2c pinmux is enabled.
Signed-off-by: Da Xue <da@libre.computer>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250425203118.1444481-1-da@libre.computer
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Some boards have noise on the UART RX line when the UART pins are not
connected to another device (such as an USB UART adapter). This can
be addressed by using a pull up resistor. Not all boards may provide
such a pull up resistor on the PCB so enable the SoC's pull-up on the
UART RX and TX pads by default. This matches the default (from u-boot
or SoC hardware) state for the pinmux configuration on these pads.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250329185855.854186-5-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Device-tree expects absent clocks to be specified as <0> (instead of
using <>). This fixes using the FCLK4/FCLK3 clocks as they are now
seen at their correct index (while before they were recognized, but at
the correct index - resulting in the hardware using a different clock
than what the kernel sees).
Fixes: a526eeef9a81 ("arm64: dts: amlogic: gx: switch to the new PWM controller binding")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250420164801.330505-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Use the new PWM controller binding which now relies on passing all
clock inputs available on the SoC (instead of passing the "wanted"
clock input for a given board).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241227212514.1376682-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
HDMI Tx needs the system clock set on the xtal rate.
This clock is managed by the main clock controller of the related SoCs.
Currently 2 part of the display drivers race to setup the HDMI system
clock by directly poking the controller register. The clock API should
be used to setup the rate instead.
Use assigned-clock to setup the HDMI system clock.
Fixes: 6939db7e0dbf ("ARM64: dts: meson-gx: Add support for HDMI output")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240626152733.1350376-3-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
The clocks provided to HDMI tx are not consistent between gx and g12:
* gx receives the peripheral clock as 'isfr' while g12 receives it as
'iahb'
* g12 gets the HDMI system clock as 'isfr' but gx does not even get it.
It surely needs that clock since the driver is directly poking around
the clock controller's registers for that clock.
Align gx SoCs with g12 and provide:
* the HDMI peripheral clock as 'iahb'
* the HDMI system clock as 'isfr'
Fixes: 6939db7e0dbf ("ARM64: dts: meson-gx: Add support for HDMI output")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240626152733.1350376-2-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
HDMI Tx needs HDMI Tx memory power domain turned on. This power domain is
handled under the VPU power domain.
The HDMI Tx currently works because it is enabling the PD by directly
poking the power controller register. It is should not do that but properly
use the power domain controller.
Fix this by adding the power domain to HDMI Tx.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240625145017.1003346-3-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
So the far, GXL SoCs were using the generic mmio register based mdio
multiplexer. This properly sets one of the glue register but the SoC
actually has 3 of those registers.
One of them sets the ID under which the internal phy will advertise
itself. If nothing sets this register before linux boots (like u-boot), the
internal phy path is broken.
To address this problem, a dedicated MDIO mux driver has been
introduced. Switch to this new driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230306151354.132973-1-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
During review of a new yaml binding, affecting these dts, it turned out
that some compatibles aren't ordered as they should be. Order should be
most specific to least specific.
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/1ce888df-6096-73de-a98a-354d086428d4@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
name
Fixes:
bus@c8834000: eth-phy-mux: {...} should not be valid under {'type': 'object'}
Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-9-44351528957e@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Add SPICC Controller pin nodes for CLK line when idle for Amlogic GXL
SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221004-up-aml-fix-spi-v4-3-0342d8e10c49@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Amlogic fixes for v5.8-rc
- misc DT fixes, and SoC ID fixes
|
|
Add the "timing-adjustment" clock now that we know how it is connected
to the PRG_ETHERNET registers. It is used internally to generate the
RGMII RX delay on the MAC side (if needed).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620162347.26159-1-martin.blumenstingl@googlemail.com
|
|
The "amlogic,meson-gx-pwrc-vpu" binding only supports the VPU power
domain, while actually there are more power domains behind that set of
registers. Switch to the new bindings so we can add more power domains
as needed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161211.23685-1-martin.blumenstingl@googlemail.com
|
|
The peripheral clock of the RNG is missing for gxl while it is present
for gxbb.
Fixes: 1b3f6d148692 ("ARM64: dts: meson-gx: add clock CLKID_RNG0 to hwrng node")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200617125346.1163527-1-jbrunet@baylibre.com
|
|
Add the internal audio DAC to the gxl SoC DT
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506221656.477379-2-jbrunet@baylibre.com
|
|
Add the AIU audio device to the Amlogic GX SoC family DT.
ATM, this device provides the i2s and spdif output stages and also
the hdmi and internal codec glues.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20200421163935.775935-3-jbrunet@baylibre.com
|
|
Add the correcly architectured USB Glue node and adapt all the Amlogic
GXL and GXM board to the new organization.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326134507.4808-11-narmstrong@baylibre.com
|
|
Add the DV18 and DV19 pinmux setting for the i2c C of the gxl family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds the GXL crypto hardware node for all GXL SoCs.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-gxl-s805x-libretech-ac.dt.yaml: ethernet-phy@8: compatible: ['ethernet-phy-id0181.4400', 'ethernet-phy-ieee802.3-c22'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-axg-s400.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-axg-s400.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-g12a-u200.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-g12a-u200.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-gxbb-nanopi-k2.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too long
meson-gxl-s805x-libretech-ac.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too lon
while here, also drop the redundant reg property from meson-gxl.dtsi
because it had the same value as meson-gx.dtsi from which it inherits.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This enables the video decoder for GXBB, GXL and GXM chips
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Clk pin does not require bias, data strobe should be pulled low.
The rest of the pin (data and cmd) are pulled up.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
SimpleFB allows transferring a framebuffer from the firmware/bootloader
to the kernel, while making sure the related clocks and power supplies
stay enabled.
Add nodes for CVBS and HDMI Simple Framebuffers.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the clock inputs of the clock controllers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
On Amlogic chipsets, the bias set through pinconf applies to the pad
itself, not only the GPIO function. This means that even when we change
the function of the pad from GPIO to anything else, the bias previously
set still applies.
As we have seen with the eMMC, depending on the bias type and the function,
it may trigger problems.
The underlying issue is that we inherit whatever was left by previous user
of the pad (pinconf, u-boot or the ROM code). As a consequence, the actual
setup we will get is undefined.
There is nothing mentioned in the documentation about pad bias and pinmux
function, however leaving it undefined is not an option.
This change consistently disable the pad bias for every pinmux functions.
It seems to work well, we can only assume that the necessary bias (if any)
is already provided by the pin function itself.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
In some cases (such as a boot from SPI) the bootloader or the ROM code may
leave a bias pull-down on the mmc pins. If so the MMC will fail during the
initialisation.
Explicitly disabling the pinmux solves the problem.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
In the pinmux of the mmc clk_gate nodes, we define 2 subnodes. One for
the function definition, the other for the bias. This is not necessary
since we can define the function and the bias in the same subnode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the required peripheral clock for the efuse device.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
dtc has new checks for SPI buses. The meson dts files have a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dtb: Warning (spi_bus_bridge): /soc/periphs@c8834000/pinctrl@4b0/spi: incorrect #address-cells for SPI bus
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Vendor firmware/uboot has different reserved regions depending on
firmware version, but current codebase reserves the same regions on
GXL and GXBB, so move the additional reserved memory region to common
.dtsi.
Found when putting a recent vendor u-boot on meson-gxbb-p200.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
>From the hardware perspective, the actual pclk of the AO uarts
is the corresponding clkc_ao uart gate, not the main clock controller clk81.
This was not problem so far, because the uart_gate had
the CLK_IGNORE_UNUSED flag, which kept the gate open.
We plan to remove the CLK_IGNORE_UNUSED flag in another patch,
but before doing that, we need to fix the clock in the DTS file.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add reset lines to the mmc controllers of the meson gx and axg SoCs
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
There are a few differences between the gxbb and gxl clock controllers
which makes them incompatible. The hdmi, gp0 and fixed pll are
different. The rate of these plls reported by gxbb driver on a gxl
device would be wrong.
Remove the gxbb compatible from the gxl clock controller node so only
the correct driver is matched.
Fixes: 973fbd55b53c ("ARM64: dts: meson-gxl: Add clock nodes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The parent of the meson-gx clock controller should be the hhi system
controller, not the HIU bus. This way, the HHI register region can be
used safely by multiple drivers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This adds USB host support to the Meson GXL SoC. A dwc3 controller is
used for host-mode, while a dwc2 controller (not added in this patch
because I could not get it working) is used for device-mode only.
The dwc3 controller's internal roothub has two USB2 ports enabled but no
USB3 port. Each of the ports is supplied by a separate PHY. The USB pins
are connected to the SoC's USBHOST_A and USBOTG_B pins.
Due to the way the roothub works internally the USB PHYs are left
enabled. When the dwc3 controller is disabled the PHY is never powered on
so it does not draw any extra power. However, when the dwc3 host
controller is enabled then all PHYs also have to be enabled, otherwise
USB devices will not be detected (regardless of whether they are plugged
into an enabled port or not). This means that only the dwc3 controller
has to be enabled on boards with USB support (instead of requiring all
boards to enable the PHYs additionally with the chance of forgetting to
enable one and breaking all other ports with that as well).
This also adds the USB3 PHY which currently only does some basic
initialization. That however is required because without it high-speed
devices (like USB thumb drives) do not work on some devices (probably
because the bootloader does not configure the USB3 PHY registers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the interrupt of the internal ethernet PHY
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.16" from Kevin Hilman
- meson-gx: add VPU power domain support
- odroid-c2: add HDMI and CEC nodes
- misc cleanups
* tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxm: fix q200 interrupt number
ARM64: dts: meson-gxm: add the PHY interrupt line on Khadas VIM2
ARM64: dts: meson: add comments with the GPIO for the PHY interrupts
ARM64: dts: amlogic: use generic bus node names
ARM64: dts: meson: drop "sana" clock from SAR ADC
ARM64: dts: odroid-c2: Add HDMI and CEC Nodes
ARM64: dts: meson-gx: grow reset controller memory zone
ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards
ARM64: dts: meson-gx: add VPU power domain
|
|
The clock-names for pclk was wrongly set to "core", but the bindings
specifies "pclk".
This was not cathed until the legacy non-documented bindings were removed.
Reported-by: Andreas Färber <afaerber@suse.de>
Fixes: f72d6f6037b7 ("ARM64: dts: meson-gx: use stable UART bindings with correct gate clock")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The SAR ADC modules doesn't require The "sana" clock.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Singed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds support for the VPU Power Domain nodes, and attaches the
VPU power domain to the VPU node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.15, round 2" from Kevin Hilman:
- add support for new GPIO IRQ driver
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: add external PHY interrupt on some platforms
ARM64: dts: meson-gx: add gpio interrupt controller
ARM64: meson: enable MESON_IRQ_GPIO in Kconfig
ARM64: dts: meson-gxbb-odroidc2: fix usb1 power supply
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit platforms: DT updates for v4.15" from Kevin Hilman:
- new SoC support: A113D
- new boards: Tronsmart Vega S96, Khadas vim2
- reserved memory fixups
- gpio-names cleanups
- MMC cleanups, enable high-speed modes
- misc cleanups
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-axg: add initial A113D SoC DT support
dt-bindings: arm: amlogic: Add Meson AXG binding
ARM64: dts: meson-gx: remove unnecessary uart compatible
ARM64: dts: meson-gx: remove unnecessary clocks properties
ARM64: dts: meson-gxl: Add alternate ARM Trusted Firmware reserved memory zone
ARM64: dts: meson-gxm: enable HS400 on the vim2
ARM64: dts: meson-gxbb-nexbox-a95x: Enable USB Nodes
dt-bindings: arm: amlogic: Add Tronsmart Vega S96 binding
ARM64: dts: meson-gxm: Add Vega S96 board
ARM64: dts: meson-gxm: Add support for Khadas VIM2
ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins
ARM64: dts: meson-gxl: adjust libretech-cc gpio-line-names
ARM64: dts: meson-gxl: adjust kvim gpio-line-names
ARM64: dts: meson-gxbb: adjust odroid-c2 gpio-line-names
ARM64: dts: meson-gxbb: adjust nanopi-k2 gpio-line-names
ARM64: dts: meson-gx: adjust gpio-ranges for TEST_N
ARM64: dts: meson-gx: remove gpio offset
ARM: dts: meson8: remove gpio offset
ARM64: dts: meson-gxl-libretech-cc: enable internal phy leds
ARM64: dts: meson-gxl-libretech-cc: enable saradc
|
|
Add gpio interrupt controller to Amlogic GX family SoCs
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This year, Amlogic updated the ARM Trusted Firmware reserved memory mapping
for Meson GXL SoCs and products sold since May 2017 uses this alternate
reserved memory mapping.
But products had been sold using the previous mapping.
This issue has been explained in [1] and a dynamic solution is yet to be
found to avoid loosing another 3Mbytes of reservable memory.
In the meantime, this patch adds this alternate memory zone only for
the GXL and GXM SoCs since GXBB based new products stopped earlier.
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
Fixes: bba8e3f42736 ("ARM64: dts: meson-gx: Add firmware reserved memory zones")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
TEST_N has moved from the EE controller to the AO controller so
the gpio-ranges need to adjusted for it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
