| Age | Commit message (Collapse) | Author |
|---|
|
Move pinctrl_uart1 to keep nodes in alphabetical order. No functional
changes.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the carrier-board Micrel KSZ8081 Ethernet PHY. This is a
10/100Mbit PHY connected to the EQOS interface and shares MDIO bus with
the Ethernet PHY located on the SoM (FEC interface).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for I2S audio found on phyBOARD-Segin-i.MX93. Audio codec
TLV320AIC3007 is connected to SAI1 interface as a DAI master. MCLK is
provided from the SAI's internal audio PLL (19.2 MHz).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for both USB controllers. Set first controller in OTG mode
(USB micro-AB connector X8) and the second one in host mode (USB type A
connector X7) by default.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for CAN networking on phyBOARD-Segin-i.MX93 via the flexcan1
interface. The CAN PHY chip SN65HVD234D used on the board is compatible
with the TCAN1043 driver using the generic "can-transceiver-phy" and is
capable of up to 1Mbps data rate.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for RTC connected via I2C on phyBOARD-Segin-i.MX93. Set
default RTC by configuring the aliases.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ERR052021
Implement fix for i.MX 93 silicon errata ERR052021.
ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low
drive mode and nominal mode
Description:
uSDHC PADs have one integration issue.
When CMD/DATA lines direction change from output to input, uSDHC
controller begin sampling, the integration issue will make input
enable signal from uSDHC propagated to the PAD with a long delay,
thus the new input value on the pad comes to uSDHC lately. The
uSDHC sampled the old input value and the sampling result is wrong.
Workaround:
Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will
propagate input to uSDHC with no delay, so correct value is sampled.
This issue will wrongly trigger the start bit when sample the USDHC
command response, cause the USDHC trigger command CRC/index/endbit
error, which will finally impact the tuning pass window, especially
will impact the standard tuning logic, and can't find a correct delay
cell to get the best timing.
Based on commit bb89601282fc ("arm64: dts: imx93-11x11-evk: set SION for
cmd and data pad of USDHC").
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Until now, all usdhc2 (SD-card) pinctrl labels pointed to one pinctrl
group "usdhc2grp" which was overwritten twice by the 100 and 200 MHz
modes. Fix this by using unique pinctrl names.
Additionally, adjust MX93_PAD_SD2_CLK__USDHC2_CLK pad drive-strength
according to values obtained by measurements from the PHYTEC hardware
department to improve signal integrity.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add disable-wp flag (write-protect) to usdhc2 node (SD-card) to get rid
of the following kernel boot warning:
host does not support reading read-only switch, assuming write-enable
Micro SD cards can't be physically write-protected like full-sized
cards anyways.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Drop redundant 'no-1-8-v' flag from usdhc1 (eMMC) node. Flag is now set
by default in the SOM include file (imx93-phycore-som.dtsi).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add basic support for phyBOARD-Segin-i.MX93.
Main features are:
* eMMC
* Ethernet
* SD-Card
* UART
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
