| Age | Commit message (Collapse) | Author |
|---|
|
Add a device tree node for the MDIO controller on the RTL9300 chips.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Define a gpio-restart node to the Cisco SG220-26P so the device can be
rebooted using the SoC's hard reset pin. Set the priority to 192 so the
gpio-restart method takes priority over the watchdog restart.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add some of the SoC's CPU peripherals currently supported:
- GPIO controller with support for 24 GPIO lines, although not all
lines are brought out to pads on the SoC package. These lines can
generate interrupts from external sources.
- Watchdog which can be used to restart the SoC if no external restart
logic is present.
- SPI controller, primarily used to access NOR flash
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add a fixed clock to define the clock frequency of the Lexra bus and use
this for the two uart nodes instead of a separate clock-frequency
property.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The uart interrupts on RTL838x chips do not lead to the CPU's interrupt
controller directly, but passes via the SoC interrupt controller. Update
the interrupt-parent property to fix this.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add the SoC interrupt controller so other components can link to it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
rtl83xx.dtsi was once (presumably) created as a base for both RTL838x
and RTL839x SoCs. Both SoCs have a different CPU and the peripherals
require different compatibles. Fold rtl83xx.dtsi into rtl838x.dtsi,
currently only supporting RTL838x SoCs, and create the RTL839x base
include later when required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Although not strictly required by the simple-bus binding, add the bus
offset to the node name to be consistent with other nodes. Also drop the
node label as it is not referenced anywhere.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The referenced CPU clock does not require any additional #clock-cells,
so drop the extraneous '0' in the referenced CPU clock.
The binding for MIPS cpus also does not allow for the clock-names
property, so just drop it.
This resolves some error message from 'dtbs_check':
cpu@0: clocks: [[4], [0]] is too long
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # For RTL9302C
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The RTL930x SoC series is sufficiently different to warrant its own base
dtsi. This ensures no properties need to be deleted or overwritten, and
prevents accidental inclusions of updates from rtl83xx.dtsi.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # For RTL9302C
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add the SPI-NAND controller on the RTL9300 family of devices. This
supports serial/dual/quad data width and DMA for read/program
operations.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add the I2C controllers that are part of the RTL9300 SoC.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The board level reset on systems using the RTL9302 can be driven via the
switch. Use a syscon-reboot node to represent this.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add support for the RTL9302 SoC and the RTL9302C_2xRTL8224_2XGE
reference board.
The RTL930x family of SoCs are Realtek switches with an embedded MIPS
core (800MHz 34Kc). Most of the peripherals are similar to the RTL838x
SoC and can make use of many existing drivers.
Add in full DSA switch support is still a work in progress.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add device_type = "cpu" to the cpu node for the rtl838x SoC. This
resolves the following dtbs_check complaint:
cpus: cpu@0: 'cache-level' is a required property
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Update the node name for the UARTs to resolve the following dtbs_check
complaints:
uart@2000: $nodename:0: 'uart@2000' does not match '^serial(@.*)?$'
uart@2100: $nodename:0: 'uart@2100' does not match '^serial(@.*)?$'
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The RTL838x/839x family of SoCs are Realtek switches with an embedded
MIPS core.
* RTL838x - 500MHz 4kce single core - 1Gbit ports and L2 features
* RTL839x - 700MHz 34Kc single core - 1Gbit ports and L2 features
These switches, depending on the exact part number, will have anywhere
between 8 and 52 ports. The MIPS core is wired to a switch cpu port which
has a tagging feature allowing us to make use of the DSA subsystem.
The SoCs are somewhat basic in certain areas, getting better with more
advanced features on newer series.
The switch functionality is MMIO-mapped via a large MFD region.
The SoCs have the following peripherals
* ethernet
* switch
* uart - ns16550a
* spi-flash interface
* gpio
* wdt
* led
The code was derived from various vendor SDKs based on Linux v2.6
kernels.
This patchset allows us to boot RTL838x/RTL839x units with basic support.
Most of the other drivers are already written and functional, and work to
get them upstream is already in progress.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
