| Age | Commit message (Collapse) | Author |
|---|
|
This adds the 4 PWM controlled green LEDs to the HiFive Unleashed device
tree. The schematic doesn't specify any special function for the LEDs,
so they're added here without any default triggers and named d1, d2, d3
and d4 just like in the schematic.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221012110928.352910-1-emil.renner.berthing@canonical.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Per HiFive Unleashed schematics, the card detect signal of the
micro SD card is connected to gpio pin #11, which should be
reflected in the DT via the <gpios> property, as described in
Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt.
[1] https://sifive.cdn.prismic.io/sifive/c52a8e32-05ce-4aaf-95c8-7bf8453f8698_hifive-unleashed-a00-schematics-1.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Fixes: d573b5558abb ("riscv: dts: add initial board data for the SiFive HiFive Unmatched")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The DTSI file defines soc node and address/size cells, so there is no
point in duplicating it in DTS file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Link: https://lore.kernel.org/r/20210920130248.145058-3-krzysztof.kozlowski@canonical.com
|
|
Add missing sifive,fu540 compatible to fix dtbs_check warnings:
arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dt.yaml: /: compatible: 'oneOf' conditional failed, one must be fixed:
['sifive,hifive-unleashed-a00', 'sifive,fu540-c000'] is too short
'sifive,hifive-unleashed-a00' is not one of ['sifive,hifive-unmatched-a00']
'sifive,fu740-c000' was expected
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Link: https://lore.kernel.org/r/20210920130248.145058-2-krzysztof.kozlowski@canonical.com
|
|
The compatible "issi,is25wp256" is undocumented and instead only a
generic jedec,spi-nor should be used (if appropriate).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210920130248.145058-1-krzysztof.kozlowski@canonical.com
|
|
VSC8541 phys need a special reset sequence, which the driver doesn't
currentlny support. As a result enabling the reset via GPIO essentially
guarnteees that the device won't work correctly. We've been relying on
bootloaders to reset the device for years, with this revert we'll go
back to doing so until we can sort out how to get the reset sequence
into the kernel.
This reverts commit a0fa9d727043da2238432471e85de0bdb8a8df65.
Fixes: a0fa9d727043 ("dts: phy: add GPIO number and active state used for phy reset")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
The GEMGXL_RST line on HiFive Unleashed is pulled low and is
using GPIO number 12. Add these reset-gpio details to dt-node
using which the linux phylib can reset the phy.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
HiFive unleashed A00 board has VSC8541-01 ethernet phy, this device is
identified as a Revision B device as described in device identification
registers. In order to use this phy in the unmanaged mode, it requires
a specific reset sequence of logical 0-1-0-1 transition on the NRESET pin
as documented here [1].
Currently, the bootloader (fsbl or u-boot-spl) takes care of the phy reset.
If due to some reason the phy device hasn't received the reset by the prior
stages before the linux macb driver comes into the picture, the MACB mii
bus gets probed but the mdio scan fails and is not even able to read the
phy ID registers. It gives an error message:
"libphy: MACB_mii_bus: probed
mdio_bus 10090000.ethernet-ffffffff: MDIO device at address 0 is missing."
Thus adding the device OUI (Organizationally Unique Identifier) to the phy
device node helps to probe the phy device.
[1]: VSC8541-01 datasheet:
https://www.mouser.com/ds/2/523/Microsemi_VSC8541-01_Datasheet_10496_V40-1148034.pdf
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add the ability to reboot the HiFive Unleashed board via GPIO.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add the gpio DT node in SiFive FU540 soc-specific DT file.
Enable the gpio node in HiFive Unleashed board-specific DT file.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add a default "stdout-path" to the kernel DTS file, as is present in many
of the board DTS files elsewhere in the kernel tree. With this line
present, earlyconsole can be enabled by simply passing "earlycon" on the
kernel command line. No specific device details are necessary, since the
kernel will use the stdout-path as the default.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
Add the PWM DT node in SiFive FU540 soc-specific DT file.
Enable the PWM nodes in HiFive Unleashed board-specific DT file.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: added chip-specific compatible string;
dropped reg-names string from pwm1]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
DT node for SiFive FU540-C000 GEMGXL Ethernet controller driver added
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Cc: Andrew Lunn <andrew@lunn.ch>
[paul.walmsley@sifive.com: changed "phy1" to "phy0" at Andrew Lunn's
suggestion]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
As per the convention for any SOC device with external connection,
define only device DT node in SOC DTSi file with status = "disabled"
and enable device in Board DTS file with status = "okay"
Reported-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Add initial board data for the SiFive HiFive Unleashed A00.
Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
|
