| Age | Commit message (Collapse) | Author |
|---|
|
The minimum size to fetch the data from device to QPIC buffer
is 512-bytes. If size is less than 512-bytes the data will not be
protected by ECC as per QPIC standard. So while reading onfi parameter
page from NAND device set nandc->buf_count = 512.
Cc: stable@vger.kernel.org
Fixes: 89550beb098e ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
For QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_param_page_type_exec() is used to read only one code word
If it configures the number of code words to 1 in QPIC_NAND_DEV0_CFG0
register then QPIC controller thinks its reading the last code word,
since we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n" register
to fetch data from QPIC buffer to system memory.
Without this change page read was failing with timeout error
/ # hexdump -C /dev/mtd1
[ 129.206113] qcom-nandc 1cc8000.nand-controller: failure to read page/oob
hexdump: /dev/mtd1: Connection timed out
This issue only seen on SDX targets since SDX target used QPICv2. But
same working on IPQ targets since IPQ used QPICv1.
Cc: stable@vger.kernel.org
Fixes: 89550beb098e ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The BAM command descriptor provides only 18 bits to specify the BAM
register offset. Additionally, in the BAM command descriptor, the BAM
register offset is supposed to be specified as "(NANDc base - BAM base)
+ reg_off". Since, the BAM controller expecting the value in the form of
"NANDc base - BAM base", so that added a new field 'bam_offset' in the NAND
properties structure and use it while preparing the command descriptor.
Previously, the driver was specifying the NANDc base address in the BAM
command descriptor.
Cc: stable@vger.kernel.org
Fixes: 8d6b6d7e135e ("mtd: nand: qcom: support for command descriptor formation")
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Gabor Juhos <j4g8y7@gmail.com> # on IPQ9574
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- The atmel,dataflash binding has been converted to yaml and the
physmap one constrained. Some logs are improved, error path are
getting reworked a bit, few patches target the use of
str_enabled_disabled().
Raw NAND changes:
- i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
SPI NAND changes:
- OTP support has been brought, and ESMT and Micron manufacturer
drivers implement it.
- Read retry, and Macronix manufacturer driver implement it.
SPI NOR changes:
- Adding support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start
using the scope based mutex cleanup helpers.
There is also a bunch of minor improvements and fixes in drivers
and bindings"
* tag 'mtd/for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (34 commits)
dt-bindings: mtd: atmel,dataflash: convert txt to yaml
mtd: mchp48l640: Use str_enable_disable() in mchp48l640_write_prepare()
mtd: rawnand: gpmi: Use str_enabled_disabled() in gpmi_nand_attach_chip()
mtd: mtdpart: Do not supply NULL to printf()
dt-bindings: mtd: gpmi-nand: Add compatible string for i.MX8 chips
mtd: nand: Fix a kdoc comment
mtd: spinand: Improve spinand_info macros style
mtd: spi-nor: drop unused <linux/of_platform.h>
mtd: spi-nor: explicitly include <linux/of.h>
mtd: spi-nor: explicitly include <linux/math64.h>
mtd: spi-nor: macronix: add support for mx66{l2, u1}g45g
mtd: spi-nor: macronix: Add post_sfdp fixups for Quad Input Page Program
mtd: Fix error handling in mtd_device_parse_register() error path
mtd: capture device name setting failure when adding mtd
mtd: Add check for devm_kcalloc()
mtd: Replace kcalloc() with devm_kcalloc()
dt-bindings: mtd: physmap: Ensure all properties are defined
mtd: rawnand: brcmnand: fix PM resume warning
dt-bindings: mtd: mxc-nand: Document fsl,imx31-nand
mtd: spinand: macronix: Add support for read retry
...
|
|
With some research in some obscure old QSDK, it was possible to find the
MASK of the last register there were still set with raw shift and
convert them to FIELD_PREP API.
This is only a cleanup and modernize the code a bit and doesn't make
any behaviour change.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fix broken config in qcom_param_page_type_exec caused by copy-paste error
from commit 0c08080fd71c ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
In qcom_param_page_type_exec the value needs to be set to
nandc->regs->cfg0 instead of host->cfg0. This wrong configuration caused
the Qcom NANDC driver to malfunction on any device that makes use of it
(IPQ806x, IPQ40xx, IPQ807x, IPQ60xx) with the following error:
[ 0.885369] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[ 0.885909] nand: Micron NAND 256MiB 1,8V 8-bit
[ 0.892499] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.896823] nand: ECC (step, strength) = (512, 8) does not fit in OOB
[ 0.896836] qcom-nandc 79b0000.nand-controller: No valid ECC settings possible
[ 0.910996] bam-dma-engine 7984000.dma-controller: Cannot free busy channel
[ 0.918070] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
Restore original configuration fix the problem and makes the driver work
again.
Also restore the wrongly dropped cpu_to_le32 to correctly support BE
systems.
Cc: stable@vger.kernel.org
Fixes: 0c08080fd71c ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
Tested-by: Robert Marko <robimarko@gmail.com> # IPQ8074 and IPQ6018
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Use the bitfield macro FIELD_PREP, and GENMASK to
do the shift and mask in one go. This makes the code
more readable.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add qpic_common.c file which hold all the common
qpic APIs which will be used by both qpic raw nand
driver and qpic spi nand driver.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add qcom prefix to all the api which will be commonly
used by spi nand driver and raw nand driver.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Perform a global cleanup of the Qualcomm NAND
controller driver with the following improvements:
- Remove register value indirection API
- Remove set_reg() API
- Convert read_loc_first & read_loc_last macro to functions
- Rename multiple variables
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
|
|
qcom_misc_cmd_type_exec()
While migrating to exec_ops in commit a82990c8a409 ("mtd: rawnand: qcom:
Add read/read_start ops in exec_op path"), OP_RESET_DEVICE command handling
got broken unintentionally. Right now for the OP_RESET_DEVICE command,
qcom_misc_cmd_type_exec() will simply return 0 without handling it. Even,
if that gets fixed, an unnecessary FLASH_STATUS read descriptor command is
being added in the middle and that seems to be causing the command to fail
on IPQ806x devices.
So let's fix the above two issues to make OP_RESET_DEVICE command working
again.
Fixes: a82990c8a409 ("mtd: rawnand: qcom: Add read/read_start ops in exec_op path")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240404083157.940-1-ansuelsmth@gmail.com
|
|
We currently provide the physical address of the DMA region
rather than the output of dma_map_resource() which is obviously wrong.
Fixes: 7330fc505af4 ("mtd: rawnand: qcom: stop using phys_to_dma()")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bibek Kumar Patro <quic_bibekkum@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230913070702.12707-1-quic_bibekkum@quicinc.com
|
|
Raw NAND core changes:
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
READ/READ_START opcodes are not set in exec_op path.
Fixing that here.
While there, Steps to program the controller is common for
erase/reset/read/program page. So use a common pattern and
pull them under one function.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230818145101.23825-4-quic_mdalam@quicinc.com
|
|
Initialize buf_count and buf_start to 0 before starting the
raw read. If we will not initialize then read staus will get
updated with wrong value and we will see failure for even
successful raw read transaction.
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230818145101.23825-3-quic_mdalam@quicinc.com
|
|
Sort includes in alphabetical order.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Just use the error no returned by submit_descs() instead of overriding it
with -EIO.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-10-manivannan.sadhasivam@linaro.org
|
|
Now that the dma desc cleanup is moved inside submit_descs(), let's
simplify the call to nand_prog_page_end_op() inside qcom_nandc_write_page()
and qcom_nandc_write_page_raw() to match other functions.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-9-manivannan.sadhasivam@linaro.org
|
|
There are two types of dma descriptors being used in this driver allocated
by, prepare_bam_async_desc() and prep_adm_dma_desc() helper functions.
These functions map and prepare the descriptors to be used for dma
transfers.
And all the descriptors are submitted inside the submit_descs() function.
Once the transfer completion happens, those descriptors should be unmapped
and freed as a part of cleanup.
Currently, free_descs() function is doing the said cleanup of descriptors.
But the callers of submit_descs() are required to call free_descs() in both
the success and error cases.
Since there are no other transactions need to be done after submit_descs(),
let's just move the contents of free_descs() inside submit_descs() itself.
This makes sure that the cleanup is handled within the submit_descs()
thereby offloading the cleanup part from callers.
While at it, let's also rename the return variable from "r" to "ret".
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-8-manivannan.sadhasivam@linaro.org
|
|
Both the function arguments and the definition could be wrapped to 80
columns to save line space.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-7-manivannan.sadhasivam@linaro.org
|
|
Checkpatch complains over the usage of ENOTSUPP for new patches as below:
WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP
So let's fix the error code which is already present in qcom_check_op().
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-6-manivannan.sadhasivam@linaro.org
|
|
qcom_check_op() function checks for the invalid opcode for the instruction
types. Currently, it just returns -ENOTSUPP for all opcodes of
NAND_OP_CMD_INSTR type due to the use of "||" operator instead of "&&".
Fix it!
This also fixes the following smatch warning:
drivers/mtd/nand/raw/qcom_nandc.c:3036 qcom_check_op() warn: was && intended here instead of ||?
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202308032022.SnXkKyFs-lkp@intel.com/
Fixes: 89550beb098e ("mtd: rawnand: qcom: Implement exec_op()")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-5-manivannan.sadhasivam@linaro.org
|
|
Handle the scenario where the caller has passed an unsupported opcode to
qcom_op_cmd_mapping(). In that case, log the error and return the
-EOPNOTSUPP errono. Also, let's propagate this error code all the way up.
This also fixes the following smatch warning:
drivers/mtd/nand/raw/qcom_nandc.c:2941 qcom_op_cmd_mapping() error: uninitialized symbol 'ret'.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202308032022.SnXkKyFs-lkp@intel.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-4-manivannan.sadhasivam@linaro.org
|
|
qcom_op_cmd_mapping() function accepts opcode and returns the corresponding
command register. So let's rename the local variables and parameters to
reflect the same.
Reported-by: Miquel Raynal <miquel.raynal@bootlin.com>
Closes: https://lore.kernel.org/all/20230804190750.3367a044@xps-13/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-3-manivannan.sadhasivam@linaro.org
|
|
In all the cases, "ret" variable is assigned a value before returning it.
So there is no need to explicitly initialize it with 0.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-2-manivannan.sadhasivam@linaro.org
|
|
The naddrs variable is initialized but not used. Fixing this could have
been a matter of dropping the variable, but the right way to do it looks
a bit more complex: we can avoid useless writes to the q_op structure by
using it. In practice we could even have possible out-of-bound bugs with
the existing implementation. Let's fix all that by just performing the
right number of assignments in the addr{1,2}_reg fields.
Fixes: 89550beb098e ("mtd: rawnand: qcom: Implement exec_op()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307131959.PdPSC86K-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202307131730.NOYbcjBr-lkp@intel.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-9-miquel.raynal@bootlin.com
|
|
Instead of allocating a structure on the stack with random data and then
expect the callee to perform the initialization (which is, in general,
error prone), prefer zeroing the structure explicitly at allocation and
provide the already zeroed area, so no explicit memset operation is
needed. It is probably safer to do so, so we limit the timeframe when
dirty data could actually be accessed by mistake.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-8-miquel.raynal@bootlin.com
|
|
Fix the following checkpatch warning:
CHECK: 'tranasction' may be misspelled - perhaps 'transaction'?
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-7-miquel.raynal@bootlin.com
|
|
The main "for" loop in qcom_read_status_exec() does guard the following
to if's which are badly indented. Fix the indentation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-6-miquel.raynal@bootlin.com
|
|
Fix following checkpatch warning:
"CHECK: Please don't use multiple blank lines"
"CHECK: Please use a blank line after
function/struct/union/enum declarations"
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-5-miquel.raynal@bootlin.com
|
|
Fix the following checkpatch warning:
"CHECK: Alignment should match open parenthesis"
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-4-miquel.raynal@bootlin.com
|
|
Fix the following checkpatch warning:
"CHECK: Prefer kernel type 'u8' over 'uint8_t'"
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-3-miquel.raynal@bootlin.com
|
|
Fix the following checkpatch warning:
"CHECK: Prefer using the BIT macro"
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230716144612.32132-2-miquel.raynal@bootlin.com
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230714174751.4060439-1-robh@kernel.org
|
|
Remove legacy interface implementation
Co-developed-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230710054440.23297-2-quic_mdalam@quicinc.com
|
|
Implement exec_op() so we can later get rid of the legacy
interface implementation.
Co-developed-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230710054440.23297-1-quic_mdalam@quicinc.com
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # atmel
Reviewed-by: Paul Cercueil <paul@crapouillou.net> # ingenic
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> # ingenic
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # intel
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # meson
Acked-by: Roger Quadros <rogerq@kernel.org> # omap_elm
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> # renesas
Reviewed-by: Heiko Stuebner <heiko@sntech.de> # rockchip
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> # sunxi
Acked-by: Thierry Reding <treding@nvidia.com> # tegra
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230411113816.3472237-1-u.kleine-koenig@pengutronix.de
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230310144715.1543926-1-robh@kernel.org
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230306144141.15360-1-quic_mdalam@quicinc.com
|
|
With use_codeword_fixup enabled, any return from
mtd_device_parse_register gets overwritten. Aside from the clear bug, this
is also problematic as a parser can EPROBE_DEFER and because this is not
correctly handled, the nand is never rescanned later in the bootup
process.
An example of this problem is when smem requires additional time to be
probed and nandc use qcomsmempart as parser. Parser will return
EPROBE_DEFER but in the current code this ret gets overwritten by
qcom_nand_host_parse_boot_partitions and qcom_nand_host_init_and_register
return 0.
Correctly handle the return code from mtd_device_parse_register so that
any error from this function is not ignored.
Fixes: 862bdedd7f4b ("mtd: nand: raw: qcom_nandc: add support for unprotected spare data pages")
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221021165304.19991-1-ansuelsmth@gmail.com
|
|
IPQ8064 nand have special pages where a different layout scheme is used.
These special page are used by boot partition and on reading them
lots of warning are reported about wrong ECC data and if written to
results in broken data and not bootable device.
The layout scheme used by these special page consist in using 512 bytes
as the codeword size (even for the last codeword) while writing to CFG0
register. This forces the NAND controller to unprotect the 4 bytes of
spare data.
Since the kernel is unaware of this different layout for these special
page, it does try to protect the spare data too during read/write and
warn about CRC errors.
Add support for this by permitting the user to declare these special
pages in dts by declaring offset and size of the partition. The driver
internally will convert these value to nand pages.
On user read/write the page is checked and if it's a boot page the
correct layout is used.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-3-ansuelsmth@gmail.com
|
|
Reorder structs in nandc driver to save holes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-2-ansuelsmth@gmail.com
|
|
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f18c ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
|
|
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.
This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.
If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is
qcom_nandc_unalloc(nandc);
clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);
dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
DMA_BIDIRECTIONAL, 0);
Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.
Fixes: c76b78d8ec05 ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
|
|
The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.
For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.
Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
From QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_nandc_read_cw_raw() is used to read only one code word
at a time. If we will configure number of code words to 1 in
in QPIC_NAND_DEV0_CFG0 register then QPIC controller thinks
its reading the last code word, since from QPIC V2 onwards
we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n"
register to fetch data from controller buffer to system
memory.
Fixes: 503ee5aad430 ("mtd: rawnand: qcom: update last code word register")
Cc: stable@kernel.org
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1630998357-1359-1-git-send-email-mdalam@codeaurora.org
|
|
QPIC_EBI2_ECC_BUF_CFG register got obsolete from QPIC V2.0 onwards.
Avoid writing this register if QPIC version is V2.0 or newer.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1623134916-562-1-git-send-email-mdalam@codeaurora.org
|
|
The result of an expression consisting of a single relational operator is
already of the bool type and does not need to be evaluated explicitly.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210510114944.3527-1-thunder.leizhen@huawei.com
|
|
Commit 82bfd11f1b03 ("mtd: rawnand: qcom: Add support for Qcom SMEM
parser") made qcomsmem the only parser for qcom_nandc partitions. This
might be problematic for systems with both SPI and NAND MTD devices.
When booting from SPI flash the partition table should not apply to the
NAND flash.
Prepend cmdlinepart and ofpart parsers to allow override of the
partition parser.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/cf470f05af514acd5bd94548804ffa96b966a0a8.1619029869.git.baruch@tkos.co.il
|
