| Age | Commit message (Collapse) | Author |
|---|
|
wiphy_unregister()/wiphy_free() has been recently decoupled from
wilc_netdev_cleanup() to fix a faulty error path in sdio/spi probe
functions. However this change introduced a new failure when simply
loading then unloading the driver:
$ modprobe wilc1000-sdio; modprobe -r wilc1000-sdio
WARNING: CPU: 0 PID: 115 at net/wireless/core.c:1145 wiphy_unregister+0x904/0xc40 [cfg80211]
Modules linked in: wilc1000_sdio(-) wilc1000 cfg80211 bluetooth ecdh_generic ecc
CPU: 0 UID: 0 PID: 115 Comm: modprobe Not tainted 6.13.0-rc6+ #45
Hardware name: Atmel SAMA5
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __warn+0x118/0x27c
__warn from warn_slowpath_fmt+0xcc/0x140
warn_slowpath_fmt from wiphy_unregister+0x904/0xc40 [cfg80211]
wiphy_unregister [cfg80211] from wilc_sdio_remove+0xb0/0x15c [wilc1000_sdio]
wilc_sdio_remove [wilc1000_sdio] from sdio_bus_remove+0x104/0x3f0
sdio_bus_remove from device_release_driver_internal+0x424/0x5dc
device_release_driver_internal from driver_detach+0x120/0x224
driver_detach from bus_remove_driver+0x17c/0x314
bus_remove_driver from sys_delete_module+0x310/0x46c
sys_delete_module from ret_fast_syscall+0x0/0x1c
Exception stack(0xd0acbfa8 to 0xd0acbff0)
bfa0: 0044b210 0044b210 0044b24c 00000800 00000000 00000000
bfc0: 0044b210 0044b210 00000000 00000081 00000000 0044b210 00000000 00000000
bfe0: 00448e24 b6af99c4 0043ea0d aea2e12c
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
The warning is triggered by the fact that there is still a
wireless_device linked to the wiphy we are unregistering, due to
wiphy_unregister() now being called after net device unregister (performed
in wilc_netdev_cleanup()). Fix this warning by moving wiphy_unregister()
after wilc_netdev_cleanup() is nominal paths (ie: driver removal).
wilc_netdev_cleanup() ordering is left untouched in error paths in probe
function because net device is not registered in those paths (so the
warning can not trigger), yet the wiphy can still be registered, and we
still some cleanup steps from wilc_netdev_cleanup().
Fixes: 1be94490b6b8 ("wifi: wilc1000: unregister wiphy only if it has been registered")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250114-wilc1000_modprobe-v1-1-ad19d46f0c07@bootlin.com
|
|
There is a specific error path in probe functions in wilc drivers (both
sdio and spi) which can lead to kernel panic, as this one for example
when using SPI:
Unable to handle kernel paging request at virtual address 9f000000 when read
[9f000000] *pgd=00000000
Internal error: Oops: 5 [#1] ARM
Modules linked in: wilc1000_spi(+) crc_itu_t crc7 wilc1000 cfg80211 bluetooth ecdh_generic ecc
CPU: 0 UID: 0 PID: 106 Comm: modprobe Not tainted 6.13.0-rc3+ #22
Hardware name: Atmel SAMA5
PC is at wiphy_unregister+0x244/0xc40 [cfg80211]
LR is at wiphy_unregister+0x1c0/0xc40 [cfg80211]
[...]
wiphy_unregister [cfg80211] from wilc_netdev_cleanup+0x380/0x494 [wilc1000]
wilc_netdev_cleanup [wilc1000] from wilc_bus_probe+0x360/0x834 [wilc1000_spi]
wilc_bus_probe [wilc1000_spi] from spi_probe+0x15c/0x1d4
spi_probe from really_probe+0x270/0xb2c
really_probe from __driver_probe_device+0x1dc/0x4e8
__driver_probe_device from driver_probe_device+0x5c/0x140
driver_probe_device from __driver_attach+0x220/0x540
__driver_attach from bus_for_each_dev+0x13c/0x1a8
bus_for_each_dev from bus_add_driver+0x2a0/0x6a4
bus_add_driver from driver_register+0x27c/0x51c
driver_register from do_one_initcall+0xf8/0x564
do_one_initcall from do_init_module+0x2e4/0x82c
do_init_module from load_module+0x59a0/0x70c4
load_module from init_module_from_file+0x100/0x148
init_module_from_file from sys_finit_module+0x2fc/0x924
sys_finit_module from ret_fast_syscall+0x0/0x1c
The issue can easily be reproduced, for example by not wiring correctly
a wilc device through SPI (and so, make it unresponsive to early SPI
commands). It is due to a recent change decoupling wiphy allocation from
wiphy registration, however wilc_netdev_cleanup has not been updated
accordingly, letting it possibly call wiphy unregister on a wiphy which
has never been registered.
Fix this crash by moving wiphy_unregister/wiphy_free out of
wilc_netdev_cleanup, and by adjusting error paths in both drivers
Fixes: fbdf0c5248dc ("wifi: wilc1000: Register wiphy after reading out chipid")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241223-wilc_fix_probe_error_path-v1-1-91fa7bd8e5b6@bootlin.com
|
|
Add support for the WILC3000 chip. The chip is similar to WILC1000,
except that the register layout is slightly different and it does
not support WPA3/SAE.
Reviewed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Tested-on: WILC1000SD 07 SDIO WILC_WIFI_FW_REL_16_1_2
Tested-on: WILC1000SD 07 SPI WILC_WIFI_FW_REL_16_1_2
Tested-on: WILC3000 A SDIO WILC_WIFI_FW_REL_16_1_1
Tested-on: WILC3000 A SPI WILC_WIFI_FW_REL_16_1_1
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241004114551.40236-7-marex@denx.de
|
|
Register wiphy after reading out chipid, so the chipid can be
used to determine chip features and not advertise WPA3/SAE
support to userspace on WILC3000. Note that wilc_netdev_cleanup()
will deregister the wiphy in fail path.
Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Tested-on: WILC1000SD 07 SDIO WILC_WIFI_FW_REL_16_1_2
Tested-on: WILC3000 A SDIO WILC_WIFI_FW_REL_16_1_1
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241004114551.40236-6-marex@denx.de
|
|
Add error handling to chip_wakeup() and propagate the errors throughout
the entire driver. Add error handling to acquire_bus()/release_bus() and
host_sleep_notify()/host_wakeup_notify() functions as a result as well.
Fill the error handling to all call sites.
Reviewed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241004114551.40236-4-marex@denx.de
|
|
Reduce the use of wilc_get_chipid(), use cached chip ID wherever
possible. Remove duplicated partial chip ID read implementations
from the driver. Update wilc_get_chipid() to always read the chip
ID out of the hardware and update the cached chip ID, and make it
return a proper return value instead of a chipid. Call wilc_get_chipid()
early to make the cached chip ID available to various sites using
is_wilc1000() to access the cached chip ID.
Reviewed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241004114551.40236-2-marex@denx.de
|
|
The WILC3000 can suspend and enter low power state. According to local
measurements, the WILC3000 consumes the same amount of power if the slot
is powered up and WILC3000 is suspended, and if the WILC3000 is powered
off. Use the former option, keep the WILC3000 powered up as that allows
for things like WoWlan to work.
Note that this is tested on WILC3000 only, not on WILC1000 .
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240926195113.2823392-1-marex@denx.de
|
|
wilc_sdio_probe()
Use devm_clk_get_optional_enabled() instead of devm_clk_get_optional() +
clk_prepare_enable(), which can make the clk consistent with the device
life cycle and reduce the risk of unreleased clk resources. Since the
device framework has automatically released the clk resource, there is
no need to execute clk_disable_unprepare(clk) on the error path, drop
the clk_disable_unprepare label, and the original error process can change
to dispose_irq.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240903110205.4127706-2-lizetao1@huawei.com
|
|
The wilc_sdio_suspend() does clk_disable_unprepare() on rtc_clk clock,
make sure wilc_sdio_resume() does matching clk_prepare_enable(), else
any suspend/resume cycle leads to clock disable/enable imbalance. Fix
the imbalance.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240821183717.163235-1-marex@denx.de
|
|
In case the hardware is not initialized, do not operate it during
suspend/resume cycle, the hardware is already off so there is no
reason to access it.
In fact, wilc_sdio_enable_interrupt() in the resume callback does
interfere with the same call when initializing the hardware after
resume and makes such initialization after resume fail. Fix this
by not operating uninitialized hardware during suspend/resume.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240821183639.163187-1-marex@denx.de
|
|
Issuing a system suspend command raises the following warning:
WARNING: CPU: 0 PID: 15 at drivers/mmc/core/sdio.c:1042 mmc_sdio_suspend+0xd4/0x19c
CPU: 0 PID: 15 Comm: kworker/u2:1 Not tainted 6.7.0-rc1-wt+ #710
Hardware name: Atmel SAMA5
Workqueue: events_unbound async_run_entry_fn
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from __warn+0x98/0x160
__warn from warn_slowpath_fmt+0xcc/0x140
warn_slowpath_fmt from mmc_sdio_suspend+0xd4/0x19c
mmc_sdio_suspend from mmc_bus_suspend+0x50/0x70
mmc_bus_suspend from dpm_run_callback+0xe4/0x248
dpm_run_callback from __device_suspend+0x234/0x91c
__device_suspend from async_suspend+0x24/0x9c
async_suspend from async_run_entry_fn+0x6c/0x210
async_run_entry_fn from process_one_work+0x3a0/0x870
[...]
This warning is due to a check in SDIO core ensuring that interrupts do not
remain enabled for cards being powered down during suspend. WILC driver
currently does not set the MMC_PM_KEEP_POWER flag, so disable interrupt
when entering resume.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-6-c2f766d0988c@bootlin.com
|
|
WILC1000 suspend/resume implementation is currently composed of two parts:
suspend/resume ops implemented in cfg80211 ops, which merely sets a
flag, and suspend/resume ops in sdio/spi driver which, based on this flag,
execute or not the suspend/resume mechanism. This dual set of ops is not
really needed , so keep only the sdio part to implement suspend/resume.
While doing so, remove the now unused suspend_event flag.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-5-c2f766d0988c@bootlin.com
|
|
Just move the suspend method next to the resume method in the sdio part
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-4-c2f766d0988c@bootlin.com
|
|
There is no reason to keep the MMC host claimed during suspend.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-3-c2f766d0988c@bootlin.com
|
|
wake/sleep
host_wakeup_notify and host_sleep_notify are surrounded by chip_wakeup and
chip_allow_sleep calls, which theorically need to be protected with the
hif_cs lock. This lock protection is currently missing. Instead of adding
the lock where those two functions are called, move those in host->chip
suspend notifications to benefit from the lock already used there (in
bus_acquire/bus_release)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-2-c2f766d0988c@bootlin.com
|
|
Driver systematically disables some power mechanism each time it starts the
chip firmware (so mostly when interface is brought up). This has a negative
impact on some specific scenarios when the chip is exposed as a
hotpluggable SDIO card (eg: WILC1000 SD):
- when executing suspend/resume sequence while interface has been brought
up
- rebooting the platform while module is plugged and interface has been
brought up
Those scenarios lead to mmc core trying to initialize again the chip which
is now unresponsive (because of the power sequencer setting), so it fails
in mmc_rescan->mmc_attach_sdio and enter a failure loop while trying to
send CMD5:
mmc0: error -110 whilst initialising SDIO card
mmc0: error -110 whilst initialising SDIO card
mmc0: error -110 whilst initialising SDIO card
[...]
Preventing the driver from disabling this "power sequencer" fixes those
enumeration issues without affecting nominal operations.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-1-c2f766d0988c@bootlin.com
|
|
The default netdev interface exposed by WILC1000 is registered at probe,
but the chip mac address is not known until ndo_open, which will load and
start chip firmware and then retrieve stored MAC address from it. As a
consequence, the interface has uninitialized value (00:00:00:00:00) until a
user brings up the interface.
Fix MAC address at probe by setting the following steps:
- at probe, read MAC address directly from fuse
- whenever a new netdevice is created, apply saved mac address (which can
be a user-provided address, or the eFuse Mac address if no address has
been passed by user)
- whenever an interface is brought up for the first time (and so the
firmware is loaded and started), enforce netdevice mac address to the
chip (in case user has changed it)
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Closes: https://lore.kernel.org/netdev/CAEyMn7aV-B4OEhHR4Ad0LM3sKCz1-nDqSb9uZNmRWR-hMZ=z+A@mail.gmail.com/T/
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240514-mac_addr_at_probe-v2-6-afef09f1cd10@bootlin.com
|
|
In order to be able to read raw registers (eg the nv mac address) in
wilc1000 during probe before the firmware is loaded and running, we need to
run the basic sdio functions initialization, but then we also need to
properly deinitialize those right after, to preserve the current driver
behavior (keeping the chip idle/unconfigured until the corresponding
interface is brought up). Calling wilc_sdio_deinit in its current form is
not enough because it merely resets an internal flag.
Implement a deinit sequence which symmetrically reset all steps performed
in wilc_sdio_init (only for parts activating/deactivating features, for the
sake of simplicity, let's ignore blocks size configuration reset)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240514-mac_addr_at_probe-v2-5-afef09f1cd10@bootlin.com
|
|
SDIO/SPI probes functions automatically add a default wlan interface on top
of registered wiphy, through wilc_cfg80211_init which in turn calls
wilc_netdev_ifc_init. However, bus is still not fully initialized when we
register corresponding net device (for example we still miss some private
driver data pointers), which for example makes it impossible to
retrieve MAC address from chip (which is supposed to be set on net device
before its registration) before registering net device. More generally, net
device registration should not be done until driver has fully initialized
everything and is ready to handle any operation on the net device.
Prevent net device from being registered so early by doing it at the end of
probe functions. Apply this logic to both sdio and spi buses.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240514-mac_addr_at_probe-v2-2-afef09f1cd10@bootlin.com
|
|
Use module_sdio_driver() instead of open-coding it. No functional
difference.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240329171019.63836-5-krzysztof.kozlowski@linaro.org
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Atmel WILC1000 SPI driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130104243.3025393-9-leitao@debian.org
|
|
Ensure 'sdio_release_host()' is always issued on return
from 'wilc_sdio_cmd53()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026141016.71407-2-dmantipov@yandex.ru
|
|
The 'enhance throughput flow' algorithm is used by default. So older
sections of the code are removed so as to always use this new algorithm.
Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230710094401.235222-1-prasurjya.rohansaikia@microchip.com
|
|
There are no SDIO module aliases included in the driver, therefore,
module autoloading isn't working. Add the proper MODULE_DEVICE_TABLE().
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027171221.491937-1-michael@walle.cc
|
|
Sometimes 'wilc_sdio_cmd53' is called with addresses pointing to an
object on the stack. Use dynamically allocated memory for cmd53 instead
of stack address which is not DMA'able.
Fixes: 5625f965d764 ("wilc1000: move wilc driver out of staging")
Reported-by: Michael Walle <mwalle@kernel.org>
Suggested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Tested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809075749.62752-1-ajay.kathat@microchip.com
|
|
Similar to SPI priv data, add 'isinit' variable in SDIO priv. Make use
of the state to invoke hif_init() once, and acquire the lock before
accessing hif function.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220720160302.231516-7-ajay.kathat@microchip.com
|
|
The function number was not correct(reset to 0) when host resumes from
suspend state. Use hardcoded value in function base information
register(FBR base address) to re-initialize correctly on host resume.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-2-ajay.kathat@microchip.com
|
|
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3bcd ("wilc1000: use goto labels on error path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
|
|
For SPI bus, the register read fails after read/write to the clockless
register during chip wakeup sequence. Add workaround to send CMD_RESET
command during chip wake-up sequence to overcome the issue.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-7-ajay.kathat@microchip.com
|
|
Use devm_clk_get_optional() for rtc clock: it simplifies a bit
the code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-4-claudiu.beznea@microchip.com
|
|
Dispose IRQ on failure path.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-3-claudiu.beznea@microchip.com
|
|
Use goto labels on error path for probe functions. This makes code easier
to read. With this introduce also netdev_cleanup and call it where
necessary.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210806081229.721731-2-claudiu.beznea@microchip.com
|
|
Write the value instead of reading it twice.
Fixes: c5c77ba18ea6 ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210224163706.519658-1-marcus.folkesson@gmail.com
|
|
When devm_clk_get() returns -EPROBE_DEFER, sdio_priv
should be freed just like when wilc_cfg80211_init()
fails.
Fixes: 8692b047e86cf ("staging: wilc1000: look for rtc_clk clock")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820054819.23365-1-dinghao.liu@zju.edu.cn
|
|
Moved macros used for Vendor/Device ID from wilc1000 driver to common
header file and changed macro name for consistency with other macros.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717051134.19160-1-ajay.kathat@microchip.com
|
|
WILC1000 is an IEEE 802.11 b/g/n IoT link controller module. The
WILC1000 connects to Microchip AVR/SMART MCUs, SMART MPUs, and other
processors with minimal resource requirements with a simple
SPI/SDIO-to-Wi-Fi interface.
WILC1000 driver has been part of staging for few years. With
contributions from the community, it has improved significantly. Full
driver review has helped in achieving the current state.
The details for those reviews are captured in 1 & 2.
[1]. https://lore.kernel.org/linux-wireless/1537957525-11467-1-git-send-email-ajay.kathat@microchip.com/
[2]. https://lore.kernel.org/linux-wireless/1562896697-8002-1-git-send-email-ajay.kathat@microchip.com/
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
