| Age | Commit message (Collapse) | Author |
|---|
|
The layout struct of efuse should not do address alignment by compiler.
Otherwise it leads unexpected layout and size for certain arch suc as arm.
In x86-64, the results are identical before and after this patch.
Also adjust bit-field to prevent over adjacent byte to avoid warning:
rtw88/rtw8822b.h:66:1: note: offset of packed bit-field `res2` has changed in GCC 4.4
66 | } __packed;
| ^
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412120131.qk0x6OhE-lkp@intel.com/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241212054203.135046-1-pkshih@realtek.com
|
|
The Realtek wifi 5 devices which support USB 3 are weird: when first
plugged in, they pretend to be USB 2. The driver needs to send some
commands to the device, which make it disappear and come back as a
USB 3 device.
Implement the required commands in rtw88.
When a USB 3 device is plugged into a USB 2 port, rtw88 will try to
switch it to USB 3 mode only once. The device will disappear and come
back still in USB 2 mode, of course.
Some people experience heavy interference in the 2.4 GHz band in
USB 3 mode, so add a module parameter switch_usb_mode with the
default value 1 to let people disable the switching.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/77906c62-5674-426f-bde1-1b2a12a0339d@gmail.com
|
|
The efuse of the SDIO RTL8822CS chip has only one known member: the mac
address is at offset 0x16a. Add a struct rtw8822cs_efuse describing this
and use it for copying the mac address when the SDIO bus is used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230218152944.48842-6-martin.blumenstingl@googlemail.com
|
|
Sparse reports the following:
CHECK drivers/net/wireless/realtek/rtw88/rtw8822c.c
drivers/net/wireless/realtek/rtw88/rtw8822c.c:5313:22: warning: symbol 'rtw8822c_hw_spec' was not declared. Should it be static?
The warning arises because the external declaration for rtw8822c_hw_spec
occurs in rtw8822ce.h, which is not included in rtw8822c.h. That line is
moved, and the now empty file rtw8822ce.h is deleted.
Symbol 'rtw8822c_hw_spec' can be made constant.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220524153621.19027-3-Larry.Finger@lwfinger.net
|
|
Declare this function allows us to use customized scanning policy.
By doing so we can be more time efficient on each scan. In order to
make existing coex mechanism work as usual, firmware notifies driver
on each channel switch event, then decide antenna ownership based on
the current channel/band. Do note that this new mechanism affects
throughput more than the sw_scan we used to have, but the overall
average throughput is not affected since each scan take less time.
Since the firmware size is limited, we only support probe requests
with custom IEs length under 128 bytes for now, if any user space
tools requires more than that, we'll introduce related changes
afterwards. For backward compatibility, we fallback to sw_scan when
using older firmware that does not support this feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221085010.39421-1-pkshih@realtek.com
|
|
Add Energy Detected CCA (EDCCA) mechanism to detect energy on the channel.
And EDCCA support adaptivity mode now. From MIC Ordinance Regulating Radio
Equipment article 49.20, ETSI EN-300-328 and EN-301-893, the device should
be able to dynamically pause TX activity when energy detected on the air.
According to ETSI/JP DFS region, driver will set corresponding threshold
and stop TX activity if the detected energy exceeds the threshold. For now,
we support it on 8822b and 8822c first.
By default, EDCCA mechanism is turned on. For ETSI/JP DFS region, it will
turn to adaptivity mode. However, with adaptivity, if environment is too
noisy, TX may often be halted. So, a debugfs for EDCCA is added. It can
show what EDCCA mode is used currently. And EDCCA mechanism can be turned
on/off through the debugfs while debugging.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-4-pkshih@realtek.com
|
|
gap-k is a calibration mechanism to eliminate power gaps between
two nearly rate groups.
This mechanism improves performance in long range test by applying
proper power value to those rate groups which have nonlinear power gap.
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419003748.3224-3-pkshih@realtek.com
|
|
This patch doesn't change logic at all, just a refactor patch.
1. Move BIT MASK and BIT definition along with the register definition
2. Remove redundant definition
3. Align macros with Tab key
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419003748.3224-2-pkshih@realtek.com
|
|
Add CFO tracking, which stands for central frequency offset tracking, to
adjust oscillator to align central frequency of connected AP. Then, it can
yield better performance.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210416030901.7099-1-pkshih@realtek.com
|
|
Register rrsr determines the response rate we send.
In field tests, using rate higher than current tx rate could lead
to difficulty for the receiving end to receive management/control
frames. Calculate current modulation level by tx rate then cross out
rate higher than those.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-2-pkshih@realtek.com
|
|
8822C devices have power trim, thermal and PA bias values
programmed in efuse. Driver should configure the RF components
according to the values.
If the power trim is not configured, then the devices might have
distortion on the output tx power.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420105207.31899-1-yhchuang@realtek.com
|
|
According to some experiments, the original RF register protection
setting of 8822c cannot perfectly make sure that there is no hardware
PI write (direct) during direct write. Modify the setting so that the
hardware block of PI would be turned off via rtw8822c_rstb_3wire()
during the direct write, to avoid RF register racing.
Note that 8822b uses SIPI write (indirect), so 8822b does not
have such problem.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This commit adds several Tx/Rx physical information to phy_info
debugfs for 8822B/8822C. By this debugfs, we can know physical
information, such as Tx/Rx rate, RSSI, EVM,SNR, etc. The
information is gotten from the packets of Tx/Rx path. It has
no impact for the performance of 8822B/8822C.
In the fields, we may meet different kinds of problems, but
we may have no professional instrument to check them. At
this moment, this debugfs is a good tool, and it may provide
useful information for debug.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
DACK is done right after the hardware has been turned on, which
means it will be done every time we leave the IDLE state.
But it takes ~2 seconds to finish DACK.
We can back up the results and restore them. And it only takes a few
milliseconds to restore the results to the hardware, saving a lot of
time.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
8822c used to count OFDM FA count by subtracting tx count from FA count.
But it need to substract more counters to be accurate.
However, we can count it by adding up all of the FA counters we want.
And it is simpler to add than list all of the components to substract.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Driver Could fail to reset counter if rx clock gating is not disabled.
So we need to disable rx clock gating before resetting counters.
Otherwise counters may increase unexpected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In 2G channels, the cck source and rxagc should be set to different
values based on different bandwidth to increase the performance of rx
sensitivity.
To improve rx throughput performance, the values of sbd subtune and
pt_opt should be changed in different bandwidth.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a new mac80211 driver for Realtek 802.11ac wireless network chips.
rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode
functionalities. The firmware for both can be found at linux-firmware.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
For RTL8822BE: rtw88/rtw8822b_fw.bin
For RTL8822CE: rtw88/rtw8822c_fw.bin
And for now, only PCI buses (RTL8xxxE) are supported. We will add support
for USB and SDIO in the future. The bus interface abstraction can be seen
in this driver such as hci.h. Most of the hardware setting are the same
except for some TRX path or probing setup should be separated.
Supported:
* Basic STA/AP/ADHOC mode, and TDLS (STA is well tested)
Missing feature:
* WOW/PNO
* USB & SDIO bus (such as RTL8xxxU/RTL8xxxS)
* BT coexistence (8822B/8822C are combo ICs)
* Multiple interfaces (for now single STA is better supported)
* Dynamic hardware calibrations (to improve/stabilize performance)
Potential problems:
* static calibration spends too much time, and it is painful for
driver to leave IDLE state. And slows down associate process.
But reload function are under development, will be added soon!
* TRX statictics misleading, as we are not reporting status correctly,
or say, not reporting for "every" packet.
The next patch set should have BT coexistence code since RTL8822B/C are
combo ICs, and the driver for BT can be found after Linux Kernel v4.20.
So it is better to add it first to make WiFi + BT work concurrently.
Although now rtw88 is simple but we are developing more features for it.
Even we want to add support for more chips such as RTL8821C/RTL8814B.
Finally, rtw88 has many authors, listed alphabetically:
Ping-Ke Shih <pkshih@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
