| Age | Commit message (Collapse) | Author |
|---|
|
_dpk_dgain_read()
The return value of _dpk_dgain_read() is not used afterward, so remove
it safely.
Addresses-Coverity-ID: 1504753 ("Unused value")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241209042020.21290-2-pkshih@realtek.com
|
|
No longer access chan with hard-code RTW89_CHANCTX_X whenever possible.
Instead, obtain the right chanctx from somewhere and use it in RTL8851B
RFK (RF calibration) related code.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240819091724.33730-3-pkshih@realtek.com
|
|
Originally, rtw89_btc_phymap() and rtw89_btc_path_phymap() access chan
with hard-code RTW89_CHANCTX_0. But, they are problematic when the chip
supports multiple channels.
So, change their prototype and pass chanctx_idx ahead. Let callers still
pass RTW89_CHANCTX_0 for now, but we will refine callers in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-8-pkshih@realtek.com
|
|
Originally, we planed to fill MAC_0/1 indicators with chanctx and
use sub_entity_xxx for these things. However, there are some reasons
listed below which make us give up this plan after we know our Wi-Fi 7
HW design.
1. one link is bound to one HW band during its life time
but, one link might change chanctx dynamically
2. in concurrent mode, assume 1st vif is MLD
1st vif's 2nd link might use the same chanctx as 2nd vif
but, they are not on the same HW band
So, we let sub_entity_xxx stuffs deal with only chanctx now. And, to be
more readable, we rename sub_entity related words to chanctx.
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-4-pkshih@realtek.com
|
|
The main change is to adjust RX calibration groups from {0,1,2,3} to {0,2}
in 5 GHz, so reduce elements from 4 to 2, and use index to iterate them.
Meanwhile, always do RX narrowband calibration (ID_NBRXK) for each group.
NCTL is used to assist IQK, so also update NCTL to 0x6 along with internal
tag HALRF_029_00_103.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-5-pkshih@realtek.com
|
|
LCK is short for LC Tank calibration. To keep RF performance, do this
calibration if difference of thermal value is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-4-pkshih@realtek.com
|
|
Fix spelling typo of IQK debug messages.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614081555.91395-3-dmantipov@yandex.ru
|
|
Drop useless '_iqk_track()' and 'rtw8852a_iqk_track()' (they
just change 'thermal_rek_en' field which is set but unused
and so removed as well) functions, set but unused 'kcount'
field of 'struct rtw89_iqk_info', and convert 'thermal' to
local variables where appropriate (it doesn't need to have
longer storage duration because it is actually used for the
debugging purposes only).
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614081555.91395-2-dmantipov@yandex.ru
|
|
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522085924.913649-1-colin.i.king@gmail.com
|
|
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-4-pkshih@realtek.com
|
|
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-3-pkshih@realtek.com
|
|
RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-2-pkshih@realtek.com
|
|
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-6-pkshih@realtek.com
|
|
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output good quality signals.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-5-pkshih@realtek.com
|
|
RCK is synchronize RC calibration. Driver triggers this calibration and
sets the result to register. This calibration is needed once when interface
is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-4-pkshih@realtek.com
|
|
Automatic amplitude control calibration (AACK) is the calibration to ensure
the oscillator is biased for a constant output amplitude. We do this
calibration if card does power on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-3-pkshih@realtek.com
|
|
Add to set RF registers according to the channel we want to switch. The
callers will be added afterward.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-2-pkshih@realtek.com
|
