| Age | Commit message (Collapse) | Author |
|---|
|
8922A doesn't support broadcast/multicast traffic under MLO mode.
So let mac80211 do the encryption/decryption for us when the
connection is in MLO mode. Future BE ICs fixes this issue.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250428112456.13165-3-pkshih@realtek.com
|
|
After firmware 0.27.125.0, it adds more fields to support firmware secure
boot. Though current driver has supported the format, old driver can't
recognize the new format, increase firmware format to 2 to avoid failed
to load the firmware by old driver.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250416081241.36138-2-pkshih@realtek.com
|
|
Set SAR configs to the corresponding CRs (control registers) according to
RF path. Then, declare to support SAR by antenna in chip info.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250326020643.14487-12-pkshih@realtek.com
|
|
Some SAR sources, e.g. ACPI, may allow different SAR configs by antenna.
Previously, the minimum config between antennas was taken. Because there
are differences between HW design, different chips might have different
solutions to achieve this. So, it cannot be done through a single common
handling. Now, add the relevant skeleton for this purpose ahead.
First, add a flag into chip info to describe whether it has implemented
this function or not. Second, support to query SAR config for a given RF
path. With it, each chip can implement its own handling. Then, if a chip
declares to support this function, when it queries SAR config without a
given RF path, it gets a maximum config between antennas.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250326020643.14487-10-pkshih@realtek.com
|
|
TAS state switching mechanism now incorporates the TX ratio as a
decision parameter. The average power calculation has been improved
by using a higher resolution conversion from dBm to linear. During
scan or MCC operations, TAS state is forced to static SAR and
suspend the average power calculation. Additionally, TAS window
size depends on the regulatory domain and band to ensure compliance.
TAS is enabled when permitted by the regulatory domain and is
currently supported on the 8852CE.
For debugging, add a flag to disable_dm that can stop TAS mechanism.
Co-developed-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-3-pkshih@realtek.com
|
|
during scanning
For some packets, we could not get channel information from PPDU status.
And this causes wrong frequencies being reported. Parse the channel
information from IE if provided by AP to fix this.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250220064357.17962-1-pkshih@realtek.com
|
|
For 8852BTE, 8852CE, and 8922AE, TKIP encryption and decryption
will be handled by hardware. All other chips will retain their
existing software-based encryption and decryption.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250220062344.15836-1-pkshih@realtek.com
|
|
To ensure secure chip only runs expected secure firmware, stop using
obsolete firmware in blacklist which weakness or flaw was found.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250217064308.43559-2-pkshih@realtek.com
|
|
BT-coexistence configure WiFi TX time to share time slots with Bluetooth
devices. Since the format is different from WiFi 6 chips, add the new
format accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250217063053.38936-3-pkshih@realtek.com
|
|
The registers of EDCCA log for PHY 1 isn't a simple offset, so define
them accordingly. Then the function use register set to access reports
according to phy_idx.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250117072828.16728-8-pkshih@realtek.com
|
|
To get a well Wi-Fi RF quality, Wi-Fi need to do RF calibrations. While
Wi-Fi is doing RF calibrations, driver will pause the Bluetooth traffic
to make sure the RF calibration will not be interfered by Bluetooth.
However, if the RF calibrations take too much time, Bluetooth audio
will perform a lag sound. Add a function to make Bluetooth can do
traffic between the individual calibrations to avoid Bluetooth sound
lag. And patch related A2DP coexistence mechanism actions.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250110015416.10704-2-pkshih@realtek.com
|
|
The PPDU status of probe response will fail to parse the IE due to being
filtered by the to_self check. Therefore, we parse RSSI from PHY report in
RX descriptor.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241128055433.11851-5-pkshih@realtek.com
|
|
The dynamic antenna gain (DAG) may independently apply different TX
powers for each RF path. This can be accomplished by using the larger
TX power as the reference path and adjusting the TX power of the
other path based on the difference. Currently only 8852BE/8852BTE/
8852CE are supported.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241111065132.19587-4-pkshih@realtek.com
|
|
Dynamic Antenna Gain (DAG) adjusts the transmit power based on the
platform's antenna gain. This allows for higher transmit power when
the antenna gain is lower, while still complying with regulatory
limits. The driver reads the Realtek Antenna Gain (RTAG) data from
BIOS, and DAG is only enabled when the regulatory domain allows it.
Currently, it only supports 8852BE/8852BTE/8852CE.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241111065132.19587-3-pkshih@realtek.com
|
|
To prevent chip overheating, reduce TX duty as the mechanism of thermal
protection. When temperature is raising over a threshold, send a firmware
command to reduce TX duty. If temperature is still raising, higher level
is adopted to have lower active duration.
The equation and unit of thermal values are different from chip to chip,
so define constant thresholds of thermal value to corresponding absolute
temperature of 110 and 120 degree Celsius.
Latter patch will decide which thermal threshold is adopted, and current
is still not enable thermal protection.
For debugging, add a flag to disable_dm that thermal protection can be
disabled to clarify low throughput in field.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241016133735.7571-2-pkshih@realtek.com
|
|
The return type of error code of rtw8852c_pwr_{on,off}_func() and its
callee is 'int'. Correct it.
Addresses-Coverity-ID: 1626056 ("Overflowed constant")
Addresses-Coverity-ID: 1627945 ("Overflowed constant")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241009004300.8144-7-pkshih@realtek.com
|
|
This is an intermediate version that is separated from subsequent major
MLO changes, so some functions' namings are not really determined here.
e.g. struct rtw89_vif_link *vif_to_rtwvif_safe(struct ieee80211_vif *vif)
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-2-pkshih@realtek.com
|
|
To get more accurate RSSI, this commit includes frequency domain RSSI
info in RSSI calculation. Add correspond physts parsing and macro to
get frequency domain RSSI information for supported IC.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240828055217.10263-3-pkshih@realtek.com
|
|
Configure supported link number by chip. And, introduce driver capability
flag for MLO. Driver should depend on runtime FW features and chip info to
determine whether to set the MLO capability flag or not. Once the MLO flag
is set, driver will consider/register/initialize things for MLO usages.
However, we just add the driver MLO capability flag ahead and don't really
set it. Then, we can start to tweak driver architecture for MLO. Some code
should depend on this flag. And after tweaking driver architecture is done,
we will set it based on runtime conditions as mentioned above.
Besides, MLD number supported by HW should be
chip supported mac_id number / chip supported link number
Without driver MLO capability flag, we allocate stations based on supported
mac_id number. With driver MLO capability flag, we allocate stations based
on supported MLD number.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240819091724.33730-9-pkshih@realtek.com
|
|
No longer access chan with hard-code RTW89_CHANCTX_X whenever possible.
Instead, obtain the right chanctx from somewhere and use it in RTL8852C
RFK (RF calibration) related code.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240819091724.33730-6-pkshih@realtek.com
|
|
Originally, all chips have implemented rfk_band_changed() and access chan
with hard-code RTW89_CHANCTX_0 in it. But, it's problematic when the chip
supports multiple channels.
So, change the prototype of rfk_band_changed() and pass chan ahead. And,
we will refine the implementation of each chip in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240819091724.33730-2-pkshih@realtek.com
|
|
TX EVM will significantly decrease for long packets when
the TX idle time increases. Introduce digital compensation
based on TX idle time, to mitigate TX EVM degradation, and
TX throughput improved from 1871 to 1947 Mbps.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240809072012.84152-3-pkshih@realtek.com
|
|
Enable net-detect in WoWLan stub of 8852c, and declare
net-detect support up to 8 SSIDs.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240805090028.27768-6-pkshih@realtek.com
|
|
Driver has supported different WoWLAN reason code by commit 0e5210217768
("wifi: rtw89: wow: update WoWLAN reason register for different FW")
since firmware version 0.27.80.0. The old driver can't support two
kinds of WoWLAN reason, so increase firmware format to v1.
Also driver tables of BB and RF registers and power values will be added
into v1 format.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240805090028.27768-2-pkshih@realtek.com
|
|
Add hardware encryption support for unicast management frames for
8922AE and 8852CE. Other chips will continue to use software
encryption for unicast management frames.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240731070506.46100-5-pkshih@realtek.com
|
|
For chips supporting multiple channels, they need to get target info
from rtwvif, e.g. PHY index and Chanctx index.
So, change rfk_scan prototype and pass rtwvif ahead.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-6-pkshih@realtek.com
|
|
For chips supporting multiple channels, they need to get target info
from rtwvif, e.g. PHY index and Chanctx index.
So, change rfk_channel prototype and pass rtwvif ahead.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-5-pkshih@realtek.com
|
|
Originally, we planed to fill MAC_0/1 indicators with chanctx and
use sub_entity_xxx for these things. However, there are some reasons
listed below which make us give up this plan after we know our Wi-Fi 7
HW design.
1. one link is bound to one HW band during its life time
but, one link might change chanctx dynamically
2. in concurrent mode, assume 1st vif is MLD
1st vif's 2nd link might use the same chanctx as 2nd vif
but, they are not on the same HW band
So, we let sub_entity_xxx stuffs deal with only chanctx now. And, to be
more readable, we rename sub_entity related words to chanctx.
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-4-pkshih@realtek.com
|
|
Add support for ieee80211::rfkill_poll ops. This enables periodic
monitoring of the hardware rfkill state, triggering updates when the
status changes.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240724052626.12774-3-pkshih@realtek.com
|
|
Need to update WoWLAN wakeup reason register after firmware version
0.35.22.0 for RTL8922A, and 0.27.80.0 for RTL8852CE.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-3-pkshih@realtek.com
|
|
On 802.11be chips, to consider MLO, HW doesn't design number
of support mac_id as large as before. And, it might be various
according to chip. For example, old chips support mac_id up to
128, but RTL8922a only supports mac_id up to 32.
Besides, the mac_id acquiring function will be extended when
impending MLO support.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240509090646.35304-5-pkshih@realtek.com
|
|
Power sequence is a flow to enable/disable WiFi card with hardware
parameters. Adjust power and clock parameters according to results
of internal simulation and verification, so apply them to have better
power consumption.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426061200.44262-2-pkshih@realtek.com
|
|
Some Wi-Fi chips meet card lost issue due to unstable hardware signal of
GPIO pins during power off. Reset AFEDIG register before BB reset in
power off sequence could avoid unstable signal and fix the issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426061200.44262-1-pkshih@realtek.com
|
|
8922a FW supports RNR parsing, provide template probe requests and
let FW do the replacement for SSID/BSSID/short SSIDs.
Don't declare WIPHY_FLAG_SPLIT_SCAN_6GHZ so proper IEs such as
6 GHz capabilities can be passed down within the same scan request.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240328052656.18823-3-pkshih@realtek.com
|
|
The WoWLAN reason register is used for driver to get the wakeup reason
for reporting to cfg80211, and it is different from chips. So put it
into chip information.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-2-pkshih@realtek.com
|
|
To avoid using bit fields for H2C command, rearrange the structure.
And also patch the corresponding code for the using of this structure.
No logic changes for existing chips.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-4-pkshih@realtek.com
|
|
Add a chip_ops for WiFi 7 chips to set additional RF configurations
including MLO and PLL settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-12-pkshih@realtek.com
|
|
calibrations later
The RF calibrations are moved into firmware, so we trigger calibrations by
H2C commands and wait for C2H completion events. However, these events
can be received only after HCI (i.e. PCI for now) starts, so we should
do initial RF calibrations after that.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-11-pkshih@realtek.com
|
|
The chip_ops::bb_preinit and ::bb_postinit are called before and after
loading BB parameters from tables of firmware file. The ::bb_reset is
used to reset hardware state, and currently it is not needed by 8922AE so
leave it as empty. The ::bb_sethw is to implement conditional parameters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-4-pkshih@realtek.com
|
|
Reset DMAC table, so we get expected behavior instead of random values at
early stage.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-7-pkshih@realtek.com
|
|
Do reset on CMAC tables by mac_id, so we don't get random values when
powering on. Therefore, add the same function for WiFi 7 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-6-pkshih@realtek.com
|
|
The CMAC table is used to define how hardware TX a certain packet, and
we can specify TX AMPDU size, so hardware can prepare proper retry window
buffer. Otherwise, it can't transmit with expected aggregation number.
Since each TID could have different aggregation number, the smallest number
is adopted to prevent over peer's receiving buffer.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-5-pkshih@realtek.com
|
|
For WiFi 7 chips, we add H2C command with rich fields to support MLO, so
add a chip_ops to generalize calling of update CMAC table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-4-pkshih@realtek.com
|
|
Basically, all chips can support 20/40/80MHz bandwidth, and 8952C can
support 160MHz bandwidth, which is why we introduced support_bw160 before.
The coming WiFi 7 chips will support 320MHz optionally, so change it to
bit mask instead of adding another support_bw320.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240112062640.36922-3-pkshih@realtek.com
|
|
Since coming WiFi 7 and existing chips use different update_beacon()
format, add to abstract selection of H2C command.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091359.67636-1-pkshih@realtek.com
|
|
Since chips could use different version of BA CAM H2C command, add a
chip_ops to abstract the operation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091134.67007-4-pkshih@realtek.com
|
|
WiFi 7 chips use different bb_gain_info struct, so move existing struct to
a union in advance. This doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105064228.36580-2-pkshih@realtek.com
|
|
To activate SER (system error recovery) in firmware, we have to configure
IMR to trigger interrupts, and then SER can check registers to know if it
need to reset hardware or notify driver to re-configure whole settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-4-pkshih@realtek.com
|
|
In queue empty check, one group contains 32 queues. And, the two elements,
wde_qempty_acq_num and wde_qempty_mgq_sel, are number of group and select
of group. To avoid confusing them with queue number and queue selection,
we refine their naming.
(don't change logic at all)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-5-pkshih@realtek.com
|
|
Add dynamic mechanism EDCCA (Energy Detection Clear Channel Assessment)
in track work. Using a fixed-value threshold will make EDCCA particularly
sensitive and cause failure to transmit under certain circumstances.
Therefore, the threshold is dynamically adjusted to make EDCCA suitable
for any situation.
However, in some cases, we will adjust the EDCCA threshold to the highest
level so that urgent transmissions can be performed successfully, such as
scanning.
Finally, in order to observe the EDCCA report in time, add the EDCCA perIC
register macro and EDCCA HW report analysis. EDCCA logs can be displayed
by using the EDCCA debug mask.
Signed-off-by: Yi-Chen Chen <jamie_chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231122060458.30878-3-pkshih@realtek.com
|
