| Age | Commit message (Collapse) | Author |
|---|
|
RTL8922AE-VS is a variant of RTL8922AE, which is supported by firmware
version after 0.35.54.0 and only can support up to MCS11. Add a variant
struct to describe these requirements accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250108020955.14668-3-pkshih@realtek.com
|
|
For early chips, the RX BD info contains FS/LS bits for first/last segments
of a receiving packet. For 8922AE, the FS bit should be ignored, or it
may throw warning:
rtw89_8922ae 0000:1a:00.0: skb should not be ready before first segment start
To have compatible logic, FS determined by what pending skb is existing
(!new) or not.
Since we expect every single receiving packet in single one segment,
enlarge 4 bytes for RX BD info, and add a debug message to note if
RX buffer is possibly smaller than expected size.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103025126.15378-1-pkshih@realtek.com
|
|
Specific PCI subsystem ID (SSID) of WiFi cards is used by specific
customer who want to enable various features with different arguments.
Define PCI SSID quirks tables to enable thermal protection with two kinds
of thermal values for 110 and 120 degree Celsius.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241016133735.7571-3-pkshih@realtek.com
|
|
Modern platforms can install more than 4GB memory, so DMA address can
larger than 32 bits. If a platform doesn't enable IOMMU, kernel needs extra
works of swiotlb to help DMA that packets reside on memory over 4GB.
The DMA addressing capability of Realtek WiFi chips is 36 bits, so set
LSB 4 bits of high 32-bit address to register and TX/RX descriptor, which
below figure shows 3-level pointers in TX direction, and RX direction is
similar but 2-level pointers only.
+--------+
| | register to head of TX BD
+---|----+
| +---------+
+-----> | TX BD | (in memory)
+----|----+
| +---------+
+------> | TX WD | (in memory)
+----|----+
| +--------+
+------> | skb |
+--------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240611021901.26394-1-pkshih@realtek.com
|
|
Increase PCI BER (bit error rate) count depth setting which could increase
PHY circuit fault tolerance and improve compatibility.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240329015251.22762-4-pkshih@realtek.com
|
|
The setting during suspend or resume is different between different
generation, so update it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-6-pkshih@realtek.com
|
|
PCI RX ring is a kind of read/write index ring, and DMA and ring index are
asynchronous, so suddenly driver gets newer index ahead before DMA. To
resolve this rare situation, we use a RX tag as helpers to make sure DMA
is done.
The RX tag is a 13-bit value, and range is from 1 ~ 0x1FFF, but 0 isn't
used so should be skipped.
Only enable this validation to coming WiFi 7 chips, because existing
chips use different design and don't really meet this situation.
Add missed rx_ring_eq_is_full for 8851BE by the way.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-4-pkshih@realtek.com
|
|
8922A is a 802.11be chip that can support 2/5/6 GHz bands 160MHz bandwidth.
Introduce the basic info such as firmware file name, some hardware address
and size, supported spatial stream, TX descriptor and so on, and then
we can add more attributes by later patches.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231117024029.113845-2-pkshih@realtek.com
|
|
To reduce interrupts, configure the mitigation setting of 8922AE when
bringing interface up, and then check situations to decide turning on or
off the function. With this, interrupt count decreases to 20,141 from
202,141 in period of 20 seconds.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231110012319.12727-8-pkshih@realtek.com
|
|
The handlers include three parts -- 1) configure interrupt mask;
2) enable/disable interrupt; 3) recognize (read) interrupt status.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231110012319.12727-6-pkshih@realtek.com
|
|
PCI LTR (Latency Tolerance Reporting) is a capability to yield expected
power consumption, and we configure the parameters according to design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-5-pkshih@realtek.com
|
|
In order to reuse PCI initial and configuration flows, add struct
rtw89_pci_gen_def to abstract the differences between WiFi 6/7 generations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-2-pkshih@realtek.com
|
|
The register to enable/disable PCI DMA IO has many variants, so define
and use a field to control it accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-5-pkshih@realtek.com
|
|
To make hardware efficient to determine if RX ring is full, introduce new
design that checks if reading and writing indices are equal. Comparing
to old design, initial indices of both reading and writing indices are 0
that means empty, and hardware checks full by "writing index + 1 ==
reading index". The "+1" has extra cost for hardware, so new design is
to avoid this.
Take ring size is 256 as an example, the initial reading and writing
indices are 255 and 0 respectively; the initial values mean empty. If two
indices are the same, for example 5 and 5, it means ring is full.
wp rp used_cnt state
255 0 0 initial (ring is empty)
255 1 1 receive 1st packet
255 2 2 receive 2nd packet
0 2 1 driver read 1st packet
1 2 0 driver read 2nd packet (ring is empty)
:
5 5 255 ring is full
Note: 'rp' is hardware writing index
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-4-pkshih@realtek.com
|
|
PCI rings are used to DMA TX/RX packets. The address of WiFi 7 chips are
different from previous ones, so add them according to hardware design.
Another difference is that driver doesn't need to configure BD (buffer
descriptor) RAM table, which is used by hardware to fetch BD ahead before
fetching whole TX data.
A TX ring contains numbers of TX BD (e.g. 512):
TX BD (buffer descriptor; continual memory)
+---+---+---+---+ +---+
| | | | | ... | |
+-|-+---+---+---+ +---+
|
| point to TX WD (WiFi descriptor; metadata of a skb data)
v
+------+
| |
| |
+-|----+
|
| point to a skb data
v
+------+
| |
| |
+------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-3-pkshih@realtek.com
|
|
8922AE is a PCIE 802.11be wireless adapter with PID 0x8922. We add basic
configurations including PCI DMA mode, PCI parameters, register address to
control TX/RX rings and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-2-pkshih@realtek.com
|
