| Age | Commit message (Collapse) | Author |
|---|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
LKP reports below warning when building for RISC-V with randconfig
configuration.
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:4554:25: sparse:
sparse: incorrect type in argument 4 (different base types)
@@ expected restricted __le32 [usertype] *[assigned] ptr
@@ got unsigned int * @@
Type cast to fix this warning.
Fixes: 4ca7fe99fc84 ("scsi: hisi_sas: Use macro instead of magic number")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505150705.k9ZzMxf1-lkp@intel.com/
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20250515013504.3234016-1-liyihang9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull in fixes from 6.15 and resolve a few conflicts so we can have a
clean base for UFS patches.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SATA devices are lost when FLR is performed while the controller and disks
are in suspended state.
This is because the libata layer is called to initialize the SATA device
during controller resume. If FLR is executed at this time, the IDENTIFY
command fails. As a result, the revalidate fails, and the SATA device is
disabled by the libata layer.
Wait until error handling completes.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20250414080845.1220997-5-liyihang9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In commit 21c7e972475e ("scsi: hisi_sas: Disable SATA disk phy for severe
I_T nexus reset failure"), if the softreset fails upon certain
conditions, the PHY connected to the disk is disabled directly. Manual
recovery is required, which is inconvenient for users in actual use.
In addition, SATA disks do not support simultaneous connection of multiple
hosts. Therefore, when multiple controllers are connected to a SATA disk
at the same time, the controller which is connected later failed to issue
an ATA softreset to the SATA disk. As a result, the PHY associated with
the disk is disabled and cannot be automatically recovered.
Now that, we will not focus on the execution result of softreset. No
matter whether the execution is successful or not, we will directly carry
out I_T_nexus_reset.
Fixes: 21c7e972475e ("scsi: hisi_sas: Disable SATA disk phy for severe I_T nexus reset failure")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20250414080845.1220997-4-liyihang9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove superfluous blank lines and symbols. Add spaces around operators.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20250414080845.1220997-3-liyihang9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The hisi_sas driver has a large number of magic numbers which makes for
unfriendly code reading. Use macro definitions instead.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20250414080845.1220997-2-liyihang9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull in remaining fixes from 6.15/scsi-queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The hw port ID of phy may change when inserting disks in batches, causing
the port ID in hisi_sas_port and itct to be inconsistent with the hardware,
resulting in I/O errors. The solution is to set the device state to gone to
intercept I/O sent to the device, and then execute linkreset to discard and
find the disk to re-update its information.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20250312095135.3048379-3-yangxingui@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
when a SATA disk is directly connected the SAS controller determines the
disk to which I/Os are delivered based on the port ID in the DQ entry.
When many phys are disconnected and reconnect, the port ID of phys were
changed and used by other link, resulting in I/O being sent to incorrect
disk. Data inconsistency on the SATA disk may occur during I/O retries
using the old port ID. So enable force phy, then force the command to be
executed in a certain phy, and if the actual phy ID of the port does not
match the phy configured in the command, the chip will stop delivering the
I/O to disk.
Fixes: ce60689e12dd ("scsi: hisi_sas: add v3 code to send ATA frame")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20250312095135.3048379-2-yangxingui@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
At present, we determine the protocol through the cmd type, but other cmd
types, such as vendor-specific commands, default to the PIO protocol. This
strategy often causes the execution of different vendor-specific commands
to fail. In fact, for these commands, a better way is to use the protocol
configured by the command's tf to determine its protocol.
Fixes: 6f2ff1a1311e ("hisi_sas: add v2 path to send ATA command")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20250220090011.313848-1-liyihang9@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Building with W=1 shows a warning about sas_v2_acpi_match being unused when
CONFIG_OF is disabled:
drivers/scsi/hisi_sas/hisi_sas_v2_hw.c:3635:36: error: unused variable 'sas_v2_acpi_match' [-Werror,-Wunused-const-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250225163637.4169300-1-arnd@kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr).
The major core change is the renaming of the slave_ methods plus a bit
of constification. The rest are minor updates and fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits)
scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init()
scsi: fnic: Test for memory allocation failure and return error code
scsi: fnic: Return appropriate error code from failure of scsi drv init
scsi: fnic: Return appropriate error code for mem alloc failure
scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro
scsi: fnic: Fix use of uninitialized value in debug message
scsi: fnic: Delete incorrect debugfs error handling
scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP
scsi: fnic: Remove extern definition from .c files
scsi: fnic: Remove unnecessary else and unnecessary break in FDLS
scsi: mpi3mr: Fix possible crash when setting up bsg fails
scsi: ufs: bsg: Set bsg_queue to NULL after removal
scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
scsi: st: Don't set pos_unknown just after device recognition
scsi: aic7xxx: Fix build 'aicasm' warning
scsi: Revert "scsi: ufs: core: Probe for EXT_IID support"
scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
scsi: scsi_debug: Constify sdebug_driver_template
scsi: documentation: Corrections for struct updates
scsi: driver-api: documentation: Change what is added to docbook
...
|
|
Use a plain BLK_MQ_F_* flag to select the round robin tag selection
instead of overlaying an enum with just two possible values into the
flags space.
Doing so allows adding a BLK_MQ_F_MAX sentinel for simplified overflow
checking in the messy debugfs helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250106083531.799976-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Replace all users of blk_mq_pci_map_queues with the more generic
blk_mq_map_hw_queues. This in preparation to retire
blk_mq_pci_map_queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Link: https://lore.kernel.org/r/20241202-refactor-blk-affinity-helpers-v6-5-27211e9c2cd5@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.
This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
alignment (dc395x driver and include/linux/libata.h).
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/scsi to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way do a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241028080754.429191-2-u.kleine-koenig@baylibre.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Before that, after the user triggers the dump, the latest dump
information can be viewed in the directory with the maximum number in
the dump directory.
After this series patch, the driver creates all debugfs directories and
files during initialization. Therefore, users cannot know the directory
where the latest dump information is stored. So, add latest_dump file to
notify users where the latest dump information is stored.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-14-liyihang9@huawei.com
Reviewed-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For the current debugfs of hisi_sas, after user triggers dump, the
driver allocate memory space to save the register information and create
debugfs files to display the saved information. In this process, the
debugfs files created after each dump.
Therefore, when the dump is triggered while the driver is unbind, the
following hang occurs:
[67840.853907] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a0
[67840.862947] Mem abort info:
[67840.865855] ESR = 0x0000000096000004
[67840.869713] EC = 0x25: DABT (current EL), IL = 32 bits
[67840.875125] SET = 0, FnV = 0
[67840.878291] EA = 0, S1PTW = 0
[67840.881545] FSC = 0x04: level 0 translation fault
[67840.886528] Data abort info:
[67840.889524] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[67840.895117] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[67840.900284] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[67840.905709] user pgtable: 4k pages, 48-bit VAs, pgdp=0000002803a1f000
[67840.912263] [00000000000000a0] pgd=0000000000000000, p4d=0000000000000000
[67840.919177] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[67840.996435] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[67841.003628] pc : down_write+0x30/0x98
[67841.007546] lr : start_creating.part.0+0x60/0x198
[67841.012495] sp : ffff8000b979ba20
[67841.016046] x29: ffff8000b979ba20 x28: 0000000000000010 x27: 0000000000024b40
[67841.023412] x26: 0000000000000012 x25: ffff20202b355ae8 x24: ffff20202b35a8c8
[67841.030779] x23: ffffa36877928208 x22: ffffa368b4972240 x21: ffff8000b979bb18
[67841.038147] x20: ffff00281dc1e3c0 x19: fffffffffffffffe x18: 0000000000000020
[67841.045515] x17: 0000000000000000 x16: ffffa368b128a530 x15: ffffffffffffffff
[67841.052888] x14: ffff8000b979bc18 x13: ffffffffffffffff x12: ffff8000b979bb18
[67841.060263] x11: 0000000000000000 x10: 0000000000000000 x9 : ffffa368b1289b18
[67841.067640] x8 : 0000000000000012 x7 : 0000000000000000 x6 : 00000000000003a9
[67841.075014] x5 : 0000000000000000 x4 : ffff002818c5cb00 x3 : 0000000000000001
[67841.082388] x2 : 0000000000000000 x1 : ffff002818c5cb00 x0 : 00000000000000a0
[67841.089759] Call trace:
[67841.092456] down_write+0x30/0x98
[67841.096017] start_creating.part.0+0x60/0x198
[67841.100613] debugfs_create_dir+0x48/0x1f8
[67841.104950] debugfs_create_files_v3_hw+0x88/0x348 [hisi_sas_v3_hw]
[67841.111447] debugfs_snapshot_regs_v3_hw+0x708/0x798 [hisi_sas_v3_hw]
[67841.118111] debugfs_trigger_dump_v3_hw_write+0x9c/0x120 [hisi_sas_v3_hw]
[67841.125115] full_proxy_write+0x68/0xc8
[67841.129175] vfs_write+0xd8/0x3f0
[67841.132708] ksys_write+0x70/0x108
[67841.136317] __arm64_sys_write+0x24/0x38
[67841.140440] invoke_syscall+0x50/0x128
[67841.144385] el0_svc_common.constprop.0+0xc8/0xf0
[67841.149273] do_el0_svc+0x24/0x38
[67841.152773] el0_svc+0x38/0xd8
[67841.156009] el0t_64_sync_handler+0xc0/0xc8
[67841.160361] el0t_64_sync+0x1a4/0x1a8
[67841.164189] Code: b9000882 d2800002 d2800023 f9800011 (c85ffc05)
[67841.170443] ---[ end trace 0000000000000000 ]---
To fix this issue, create all directories and files during debugfs
initialization. In this way, the driver only needs to allocate memory
space to save information each time the user triggers dumping.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-13-liyihang9@huawei.com
Reviewed-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
At present, it is found that some SATA HDD disks may continue to return
the HOLD primitive for more than 500ms when they are busy writing data,
which is more likely to trigger an STP link timeout exception. Now
Modify STP link timer from 500ms to the maximum value of 1.048575s.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-12-liyihang9@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Spec says at least 5us between two H2D FIS when do soft reset, but be
generous and sleep for about 1ms.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-11-liyihang9@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The SATA disk will be locked after the disk sends the DMA Setup frame
until all data frame transmission is completed. The
CFG_ICT_TIMER_STEP_TRSH register is used for sata disk to configure the
step size of the timer which records the time when the disk is
locked. The unit is 1us and the default step size is 150ms. If the disk
is locked for more than 7 timer steps, the io to be sent to the disk
will end abnormally.
The current timeout is only about 1 second, it is easy to trigger IO
abnormal end when the SATA hard disk returns data slowly. Adjust the
timeout to 7 seconds based on ERC time of most disks.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-10-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In the current interrupt reporting mode, each CQ entry reports an
interrupt. However, when there are a large number of I/O hardware
completion interrupts, the following issue may occur:
[ 4682.678657][ C129] irq 134: nobody cared (try booting with the "irqpoll" option)
[ 4682.708455][ C129] Call trace:
[ 4682.711589][ C129] dump_backtrace+0x0/0x1e4
[ 4682.715934][ C129] show_stack+0x20/0x2c
[ 4682.719933][ C129] dump_stack+0xd8/0x140
[ 4682.724017][ C129] __report_bad_irq+0x54/0x180
[ 4682.728625][ C129] note_interrupt+0x1ec/0x2f0
[ 4682.733143][ C129] handle_irq_event+0x118/0x1ac
[ 4682.737834][ C129] handle_fasteoi_irq+0xc8/0x200
[ 4682.742613][ C129] __handle_domain_irq+0x84/0xf0
[ 4682.747391][ C129] gic_handle_irq+0x88/0x2c0
[ 4682.751822][ C129] el1_irq+0xbc/0x140
[ 4682.755648][ C129] _find_next_bit.constprop.0+0x20/0x94
[ 4682.761036][ C129] cpumask_next+0x24/0x30
[ 4682.765208][ C129] gic_ipi_send_mask+0x48/0x170
[ 4682.769900][ C129] __ipi_send_mask+0x34/0x110
[ 4682.775720][ C129] smp_cross_call+0x3c/0xcc
[ 4682.780064][ C129] arch_send_call_function_single_ipi+0x38/0x44
[ 4682.786146][ C129] send_call_function_single_ipi+0xd0/0xe0
[ 4682.791794][ C129] generic_exec_single+0xb4/0x170
[ 4682.796659][ C129] smp_call_function_single_async+0x2c/0x40
[ 4682.802395][ C129] blk_mq_complete_request_remote.part.0+0xec/0x100
[ 4682.808822][ C129] blk_mq_complete_request+0x30/0x70
[ 4682.813950][ C129] scsi_mq_done+0x48/0xac
[ 4682.818128][ C129] sas_scsi_task_done+0xb0/0x150 [libsas]
[ 4682.823692][ C129] slot_complete_v3_hw+0x230/0x710 [hisi_sas_v3_hw]
[ 4682.830120][ C129] cq_thread_v3_hw+0xbc/0x190 [hisi_sas_v3_hw]
[ 4682.836114][ C129] irq_thread_fn+0x34/0xa4
[ 4682.840371][ C129] irq_thread+0xc4/0x130
[ 4682.844455][ C129] kthread+0x108/0x13c
[ 4682.848365][ C129] ret_from_fork+0x10/0x18
[ 4682.852621][ C129] handlers:
[ 4682.855577][ C129] [<00000000949e52bf>] cq_interrupt_v3_hw [hisi_sas_v3_hw] threaded [<000000005d8e3b68>] cq_thread_v3_hw [hisi_sas_v3_hw]
[ 4682.868084][ C129] Disabling IRQ #134
When the IRQ management layer processes each hardware interrupt, if the
return value of the interrupt handler is IRQ_WAKE_THREAD, it will wake
up the handler thread for this interrupt action and set IRQTF_RUNTHREAD
flag, wait for the interrupt handling thread to clear the
IRQTF_RUNTHREAD flag after execution. Later in note_interrupt(), use
irq_count to count hardware interrupts and irqs_unhandled to count
interrupts for which no thread handler is responsible. When irq_count
reaches 100000 and irqs_unhandled reaches 99000, irq will be disabled.
In the performance test scenario, I/O completion hardware interrupts are
continuously and quickly generated. As a result, the interrupt
processing thread is cyclically called in irq_thread() and does not
exit, this affects the response of the interrupt thread to the hardware
interrupt and causes irqs_unhandled to grow to 99000. Finally, the irq
is disabled.
Therefore, default enable interrupt coalescing to reduce the generation
of hardware interrupts, this helps interrupt processing threads to stop
calling in irq_thread().
For interrupt coalescing, according to the actual performance test, set
the count of CQ entries to 10 and the interrupt coalescing timeout
period to 10us based on the actual performance test.
Before and after interrupt coalescing is enabled, the 4K read/write
performance is improved by about 3%, and the 256K read/write performance
is basically the same.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-9-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For no forced preemption model kernel, in the scenario where the
expander is connected to 12 high performance SAS SSDs, the following
call trace may occur:
[ 214.409199][ C240] watchdog: BUG: soft lockup - CPU#240 stuck for 22s! [irq/149-hisi_sa:3211]
[ 214.568533][ C240] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--)
[ 214.575224][ C240] pc : fput_many+0x8c/0xdc
[ 214.579480][ C240] lr : fput+0x1c/0xf0
[ 214.583302][ C240] sp : ffff80002de2b900
[ 214.587298][ C240] x29: ffff80002de2b900 x28: ffff1082aa412000
[ 214.593291][ C240] x27: ffff3062a0348c08 x26: ffff80003a9f6000
[ 214.599284][ C240] x25: ffff1062bbac5c40 x24: 0000000000001000
[ 214.605277][ C240] x23: 000000000000000a x22: 0000000000000001
[ 214.611270][ C240] x21: 0000000000001000 x20: 0000000000000000
[ 214.617262][ C240] x19: ffff3062a41ae580 x18: 0000000000010000
[ 214.623255][ C240] x17: 0000000000000001 x16: ffffdb3a6efe5fc0
[ 214.629248][ C240] x15: ffffffffffffffff x14: 0000000003ffffff
[ 214.635241][ C240] x13: 000000000000ffff x12: 000000000000029c
[ 214.641234][ C240] x11: 0000000000000006 x10: ffff80003a9f7fd0
[ 214.647226][ C240] x9 : ffffdb3a6f0482fc x8 : 0000000000000001
[ 214.653219][ C240] x7 : 0000000000000002 x6 : 0000000000000080
[ 214.659212][ C240] x5 : ffff55480ee9b000 x4 : fffffde7f94c6554
[ 214.665205][ C240] x3 : 0000000000000002 x2 : 0000000000000020
[ 214.671198][ C240] x1 : 0000000000000021 x0 : ffff3062a41ae5b8
[ 214.677191][ C240] Call trace:
[ 214.680320][ C240] fput_many+0x8c/0xdc
[ 214.684230][ C240] fput+0x1c/0xf0
[ 214.687707][ C240] aio_complete_rw+0xd8/0x1fc
[ 214.692225][ C240] blkdev_bio_end_io+0x98/0x140
[ 214.696917][ C240] bio_endio+0x160/0x1bc
[ 214.701001][ C240] blk_update_request+0x1c8/0x3bc
[ 214.705867][ C240] scsi_end_request+0x3c/0x1f0
[ 214.710471][ C240] scsi_io_completion+0x7c/0x1a0
[ 214.715249][ C240] scsi_finish_command+0x104/0x140
[ 214.720200][ C240] scsi_softirq_done+0x90/0x180
[ 214.724892][ C240] blk_mq_complete_request+0x5c/0x70
[ 214.730016][ C240] scsi_mq_done+0x48/0xac
[ 214.734194][ C240] sas_scsi_task_done+0xbc/0x16c [libsas]
[ 214.739758][ C240] slot_complete_v3_hw+0x260/0x760 [hisi_sas_v3_hw]
[ 214.746185][ C240] cq_thread_v3_hw+0xbc/0x190 [hisi_sas_v3_hw]
[ 214.752179][ C240] irq_thread_fn+0x34/0xa4
[ 214.756435][ C240] irq_thread+0xc4/0x130
[ 214.760520][ C240] kthread+0x108/0x13c
[ 214.764430][ C240] ret_from_fork+0x10/0x18
This is because in the hisi_sas driver, both the hardware interrupt
handler and the interrupt thread are executed on the same CPU. In the
performance test scenario, function irq_wait_for_interrupt() will always
return 0 if lots of interrupts occurs and the CPU will be continuously
consumed. As a result, the CPU cannot run the watchdog thread. When the
watchdog time exceeds the specified time, call trace occurs.
To fix it, add cond_resched() to execute the watchdog thread.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-8-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
RPM_SUSPENDING
Users can suspend the machine with 'echo disk > /sys/power/state', but
the suspend will fail because the SAS controller cannot be suspended:
[root@localhost ~]# echo freeze > /sys/power/state
-bash: echo: write error: Device or resource busy
[15104.142955] PM: suspend entry (s2idle)
...
[15104.283465] hisi_sas_v3_hw 0000:32:04.0: entering suspend state
[15104.283480] hisi_sas_v3_hw 0000:30:04.0: entering suspend state
[15104.283500] hisi_sas_v3_hw 0000:32:04.0: PM suspend: host status cannot be suspended
[15104.283508] hisi_sas_v3_hw 0000:30:04.0: PM suspend: host status cannot be suspended
[15104.283516] hisi_sas_v3_hw 0000:32:04.0: PM: pci_pm_suspend(): suspend_v3_hw+0x0/0x210 [hisi_sas_v3_hw] returns -16
[15104.283527] hisi_sas_v3_hw 0000:32:04.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1c0 returns -16
[15104.283524] hisi_sas_v3_hw 0000:30:04.0: PM: pci_pm_suspend(): suspend_v3_hw+0x0/0x210 [hisi_sas_v3_hw] returns -16
[15104.283533] hisi_sas_v3_hw 0000:32:04.0: PM: failed to suspend async: error -16
[15104.283536] hisi_sas_v3_hw 0000:30:04.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1c0 returns -16
[15104.283542] hisi_sas_v3_hw 0000:30:04.0: PM: failed to suspend async: error -16
The problem is that when the ->runtime_suspend() callback
suspend_v3_hw() is executing, the current runtime PM status is
RPM_ACTIVE and the usage count of the controller is not 0, so return
immediately.
To fix it, Check the device usage count only when the runtime PM status
is RPM_SUSPENDING.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-7-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In commit 89954f024c3a ("scsi: hisi_sas: Ensure all enabled PHYs up
during controller reset"), we enable PHYs in parallel through async
operations and wait for PHYs come up. However, for some directly
attached SATA disks, the PHY not come up after a timeout period and the
hardware is not ready. At this time, we should get the latest PHY
hardware state, if the new PHY state is not ready but the old PHY state
is ready, call work HISI_PHYE_LINK_RESET to give it another chance to
phyup.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-6-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
controller reset
For the controller reset operation(such as FLR or clear nexus ha in SCSI
EH), we will disable all PHYs and then enable PHY based on the
hisi_hba->phy_state obtained in hisi_sas_controller_reset_prepare(). If
the device is removed before controller reset or the PHY is not attached
to any device in directly attached scenario, the corresponding bit of
phy_state is not set. After controller reset done, the PHY is disabled.
The device cannot be identified even if user reconnect the disk.
Therefore, for PHYs that are not disabled by user, hisi_sas_phy_enable()
needs to be executed even if the corresponding bit of phy_state is not
set.
Fixes: 89954f024c3a ("scsi: hisi_sas: Ensure all enabled PHYs up during controller reset")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-5-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For security purposes, after information is obtained through the FW,
check information to ensure data correctness.
- In v1 and v2 hw, the maximum number of PHYs is 9, while in v3 it is 8.
- In v2 and v3 hw, the maximum number of hardware queues is 16, while
in v1 it is 32.
Also add some debug logs for failure.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-4-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In the current debugfs initialization process, the interface
trigger_dump is created first, and then the dump directory is created to
store the register dump information.
The issue is that after the trigger_dump interface is created, users can
access the interface to trigger dump and call
debugfs_create_files_v3_hw(). In debugfs_create_files_v3_hw(), if
.debugfs_dump_dentry is NULL, the file for storing dump information is
created under /sys/kernel/debug, and the memory and information cannot
be released after the driver is uninstalled.
Therefore, the creation of the trigger_dump interface is placed at the
end of debugfs initialization.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-3-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
To be safe, we should register debugfs at the last stage of driver
initialization and then unregister debugfs at the first stage of driver
uninstallation.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-2-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is a extraneous space after a newline in a dev_info message.
Remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240902144153.309920-1-colin.i.king@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The workqueue maintainer wants to remove the create*_workqueue() macros
because these macros always set the WQ_MEM_RECLAIM flag and because these
only support literal workqueue names. Hence this patch that replaces the
create*_workqueue() invocations with the definition of this macro. The
WQ_MEM_RECLAIM flag has been retained because I think that flag is necessary
for workqueues created by storage drivers. This patch has been generated by
running spatch and git clang-format. spatch has been invoked as follows:
spatch --in-place --sp-file expand-create-workqueue.spatch $(git grep -lEw 'create_(freezable_|singlethread_|)workqueue' */scsi */ufs)
The contents of the expand-create-workqueue.spatch file is as follows:
@@
expression name;
@@
-create_workqueue(name)
+alloc_workqueue("%s", WQ_MEM_RECLAIM, 1, name)
@@
expression name;
@@
-create_freezable_workqueue(name)
+alloc_workqueue("%s", WQ_FREEZABLE | WQ_UNBOUND | WQ_MEM_RECLAIM, 1, name)
@@
expression name;
@@
-create_singlethread_workqueue(name)
+alloc_ordered_workqueue("%s", WQ_MEM_RECLAIM, name)
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240822195944.654691-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers.
The remaining patches are assorted minor fixes and deprecated function
updates plus a bit of constification"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: mpi3mr: Sanitise num_phys
scsi: lpfc: Copyright updates for 14.4.0.2 patches
scsi: lpfc: Update lpfc version to 14.4.0.2
scsi: lpfc: Add support for 32 byte CDBs
scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask
scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list
scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading
scsi: lpfc: Update logging of protection type for T10 DIF I/O
scsi: lpfc: Change default logging level for unsolicited CT MIB commands
scsi: target: Remove unused list 'device_list'
scsi: iscsi: Remove unused list 'connlist_err'
scsi: ufs: exynos: Add support for Tensor gs101 SoC
scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata
scsi: ufs: exynos: Allow max frequencies up to 267Mhz
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option
scsi: ufs: dt-bindings: exynos: Add gs101 compatible
scsi: qla2xxx: Fix debugfs output for fw_resource_count
scsi: qedf: Ensure the copied buf is NUL terminated
scsi: bfa: Ensure the copied buf is NUL terminated
...
|
|
Switch to the ->device_configure method instead of ->slave_configure and
update the block limits on the passed in queue_limits instead of using the
per-limit accessors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-21-hch@lst.de
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We found that the second parameter of function ata_wait_after_reset() is
incorrectly used. We call smp_ata_check_ready_type() to poll the device
type until the 30s timeout, so the correct deadline should be (jiffies +
30000).
Fixes: 3c2673a09cf1 ("scsi: hisi_sas: Fix SATA devices missing issue during I_T nexus reset")
Co-developed-by: xiabing <xiabing12@h-partners.com>
Signed-off-by: xiabing <xiabing12@h-partners.com>
Co-developed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/20240402035513.2024241-3-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We find that some disks use D2H frame instead of SDB frame to return NCQ
error. Currently, only the I/O corresponding to the D2H frame is processed
in this scenario, which does not meet the processing requirements of the
NCQ error scenario. So we set dev_status to HISI_SAS_DEV_NCQ_ERR and abort
all I/Os of the disk in this scenario.
Co-developed-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/20240402035513.2024241-2-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
John Garry <john.g.garry@oracle.com> says:
There is much duplication in the scsi_host_template structure for the
drivers which use libsas.
Similar to how a standard template is used in libata with
__ATA_BASE_SHT, create a standard template in LIBSAS_SHT_BASE.
Link: https://lore.kernel.org/r/20240308114339.1340549-1-john.g.garry@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use standard template for scsi_host_template structure to reduce
duplication.
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240308114339.1340549-4-john.g.garry@oracle.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The added sysfs attributes group enables the configuration of NCQ Priority
feature for HBAs that rely on libsas to manage SATA devices.
Omitted hisi_sas_v1_hw.c because v1 HW doesn't support SATA.
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240307214418.3812290-6-ipylypiv@google.com
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
hisi_hba->timer is not used for v3 hw but there are two places that some
operations related to hisi_hba->timer are called by v3 hw:
- Deleting the timer in function hisi_sas_v3_hw() which is only for v3 hw;
- Deleting the timer in function hisi_sas_controller_reset_prepare() which
is common for v1/v2/v3 hw.
We can remove the timer in the first case, but for the second scenario we
need to remove it only for v3 hw, so check hw->sht which is NULL only for
v3 hw before deleting hisi_hba->timer.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1705904747-62186-5-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
hisi_sas debugfs remove should be executed only when debugfs is enabled.
Check whether debugfs is enabled and then remove it only if enabled.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1705904747-62186-4-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In commit 63f0733d07ce ("scsi: hisi_sas: Allocate DFX memory during dump
trigger"), the memory allocation time of the DFX is changed from device
initialization to dump occurs, so .debugfs_itct is not a valid address and
do not need to check.
The parameter hisi_sas_debugfs_enable is enough to check whether automatic
debugfs dump is triggered, so remove redunant checks.
Fixes: 63f0733d07ce ("scsi: hisi_sas: Allocate DFX memory during dump trigger")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1705904747-62186-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If we issue a disabling PHY command, the device attached with it will go
offline, if a 2 bit ECC error occurs at the same time, a hung task may be
found:
[ 4613.652388] INFO: task kworker/u256:0:165233 blocked for more than 120 seconds.
[ 4613.666297] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 4613.674809] task:kworker/u256:0 state:D stack: 0 pid:165233 ppid: 2 flags:0x00000208
[ 4613.683959] Workqueue: 0000:74:02.0_disco_q sas_revalidate_domain [libsas]
[ 4613.691518] Call trace:
[ 4613.694678] __switch_to+0xf8/0x17c
[ 4613.698872] __schedule+0x660/0xee0
[ 4613.703063] schedule+0xac/0x240
[ 4613.706994] schedule_timeout+0x500/0x610
[ 4613.711705] __down+0x128/0x36c
[ 4613.715548] down+0x240/0x2d0
[ 4613.719221] hisi_sas_internal_abort_timeout+0x1bc/0x260 [hisi_sas_main]
[ 4613.726618] sas_execute_internal_abort+0x144/0x310 [libsas]
[ 4613.732976] sas_execute_internal_abort_dev+0x44/0x60 [libsas]
[ 4613.739504] hisi_sas_internal_task_abort_dev.isra.0+0xbc/0x1b0 [hisi_sas_main]
[ 4613.747499] hisi_sas_dev_gone+0x174/0x250 [hisi_sas_main]
[ 4613.753682] sas_notify_lldd_dev_gone+0xec/0x2e0 [libsas]
[ 4613.759781] sas_unregister_common_dev+0x4c/0x7a0 [libsas]
[ 4613.765962] sas_destruct_devices+0xb8/0x120 [libsas]
[ 4613.771709] sas_do_revalidate_domain.constprop.0+0x1b8/0x31c [libsas]
[ 4613.778930] sas_revalidate_domain+0x60/0xa4 [libsas]
[ 4613.784716] process_one_work+0x248/0x950
[ 4613.789424] worker_thread+0x318/0x934
[ 4613.793878] kthread+0x190/0x200
[ 4613.797810] ret_from_fork+0x10/0x18
[ 4613.802121] INFO: task kworker/u256:4:316722 blocked for more than 120 seconds.
[ 4613.816026] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 4613.824538] task:kworker/u256:4 state:D stack: 0 pid:316722 ppid: 2 flags:0x00000208
[ 4613.833670] Workqueue: 0000:74:02.0 hisi_sas_rst_work_handler [hisi_sas_main]
[ 4613.841491] Call trace:
[ 4613.844647] __switch_to+0xf8/0x17c
[ 4613.848852] __schedule+0x660/0xee0
[ 4613.853052] schedule+0xac/0x240
[ 4613.856984] schedule_timeout+0x500/0x610
[ 4613.861695] __down+0x128/0x36c
[ 4613.865542] down+0x240/0x2d0
[ 4613.869216] hisi_sas_controller_prereset+0x58/0x1fc [hisi_sas_main]
[ 4613.876324] hisi_sas_rst_work_handler+0x40/0x8c [hisi_sas_main]
[ 4613.883019] process_one_work+0x248/0x950
[ 4613.887732] worker_thread+0x318/0x934
[ 4613.892204] kthread+0x190/0x200
[ 4613.896118] ret_from_fork+0x10/0x18
[ 4613.900423] INFO: task kworker/u256:1:348985 blocked for more than 121 seconds.
[ 4613.914341] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 4613.922852] task:kworker/u256:1 state:D stack: 0 pid:348985 ppid: 2 flags:0x00000208
[ 4613.931984] Workqueue: 0000:74:02.0_event_q sas_port_event_worker [libsas]
[ 4613.939549] Call trace:
[ 4613.942702] __switch_to+0xf8/0x17c
[ 4613.946892] __schedule+0x660/0xee0
[ 4613.951083] schedule+0xac/0x240
[ 4613.955015] schedule_timeout+0x500/0x610
[ 4613.959725] wait_for_common+0x200/0x610
[ 4613.964349] wait_for_completion+0x3c/0x5c
[ 4613.969146] flush_workqueue+0x198/0x790
[ 4613.973776] sas_porte_broadcast_rcvd+0x1e8/0x320 [libsas]
[ 4613.979960] sas_port_event_worker+0x54/0xa0 [libsas]
[ 4613.985708] process_one_work+0x248/0x950
[ 4613.990420] worker_thread+0x318/0x934
[ 4613.994868] kthread+0x190/0x200
[ 4613.998800] ret_from_fork+0x10/0x18
This is because when the device goes offline, we obtain the hisi_hba
semaphore and send the ABORT_DEV command to the device. However, the
internal abort timed out due to the 2 bit ECC error and triggers automatic
dump. In addition, since the hisi_hba semaphore has been obtained, the dump
cannot be executed and the controller cannot be reset.
Therefore, the deadlocks occur on the following circular dependencies:
hisi_sas_dev_gone() -> down() -> hisi_sas_internal_task_abort_dev() -> ...
-> hisi_sas_internal_abort_timeout() -> down().
The deadlock is triggered only when the timeout occurs during device goes
offline. To fix this issue, use .rst_ha_timeout to distinguish the scenario
where a device goes offline from other scenarios.
Fixes: 2ff07b5c6fe9 ("scsi: hisi_sas: Directly call register snapshot instead of using workqueue")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1705904747-62186-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In function debugfs_debugfs_snapshot_global_reg_v3_hw() it uses
debugfs_axi_reg.count (which is the number of axi debugfs registers) to
acquire the number of global debugfs registers.
Use debugfs_global_reg.count to acquire the number of global debugfs
registers instead.
Fixes: 623a4b6d5c2a ("scsi: hisi_sas: Move debugfs code to v3 hw driver")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-6-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We obtain the semaphore and set HISI_SAS_RESETTING_BIT in
hisi_sas_reset_prepare_v3_hw(), block the scsi host and set
HISI_SAS_REJECT_CMD_BIT in hisi_sas_controller_reset_prepare(), released
them in hisi_sas_controller_reset_done(). However, if the HW reset failure
in FLR results in early return, the semaphore and flag bits will not be
release.
Rollback some operations including clearing flags / releasing semaphore
when FLR is failed.
Fixes: e5ea48014adc ("scsi: hisi_sas: Implement handlers of PCIe FLR for v3 hw")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-5-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In commit 4b329abc9180 ("scsi: hisi_sas: Move slot variable definition in
hisi_sas_abort_task()"), we move the variables slot to the function head.
However, the variable slot may be NULL, we should check it in each branch.
Fixes: 4b329abc9180 ("scsi: hisi_sas: Move slot variable definition in hisi_sas_abort_task()")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-4-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In function hisi_sas_controller_prereset(), -ENOSYS (Function not
implemented) should be returned if the driver does not support .soft_reset.
Returns -EPERM (Operation not permitted) if HISI_SAS_RESETTING_BIT is
already be set.
In function _suspend_v3_hw(), returns -EPERM (Operation not permitted) if
HISI_SAS_RESETTING_BIT is already be set.
Fixes: 4522204ab218 ("scsi: hisi_sas: tidy host controller reset function a bit")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
HISI_PHYE_PHY_UP_PM
Currently in directly attached scenario, the phyup event
HISI_PHYE_PHY_UP_PM is notified before .phy_attached is set - this may
cause the phyup work hisi_sas_bytes_dmaed() execution failed and the
attached device will not be found.
To fix it, set .phy_attached before notifing phyup event.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
