| Age | Commit message (Collapse) | Author |
|---|
|
w35n0xjw chips can run at up to 166MHz in octal mode, but this is only
possible after programming various VCR registers.
Implement the new ->configure_chip() hook for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
w25n0xjw chips have a high-speed capability hidden in a configuration
register. Once enabled, dual/quad SDR reads may be performed at a much
higher frequency.
Implement the new ->configure_chip() hook for this purpose and configure
the SR4 register accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
There is already a manufacturer hook, which is manufacturer specific but
not chip specific. We no longer have access to the actual NAND identity
at this stage so let's add a per-chip configuration hook to align the
chip configuration (if any) with the core's setting.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
These macros had initially no frequency field. When I added the "maximum
operation frequency" field, I did it initially on very common macros and
I decided to add an optional field for that (with VA_ARGS) in order to
prevent massively unreadable changes. I then added new variants in the
spinand.h header, and requested a frequency field for them by
default. Some times later, I also added maximum frequencies to other
existing variants, but I did it incorrectly, without noticing I was
wrong because the field was optional.
This mix is error prone, so let's do what I should have done since the
very beginning: add a frequency field to all READ_FROM_CACHE variants.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
No functional change, just a style fix to align with the other
macros all around.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Dual and quad capable chips natively support dual and quad I/O variants
at up to 104MHz (1-2-2 and 1-4-4 operations). Reaching the maximum speed
of 166MHz is theoretically possible (while still unsupported in the
field) by adding a few more dummy cycles. Let's be accurate and clearly
state this limit.
Setting a maximum frequency implies adding the frequency parameter to
the macro, which is done using a variadic argument to avoid impacting
all the other drivers which already make use of this macro.
Fixes: 1ea808b4d15b ("mtd: spinand: winbond: Update the *JW chip definitions")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI NAND chips may support octal "read from cache" and "program load"
transfers. List the opcodes by defining the relevant macros describing
these operations.
However, due to the hardware available I had, 0x82 and 0xc2 are
untested and given as reference, only 0xc4 could be (successfully)
tested.
Controllers supporting operations mixing SDR and DTR operations might
even leverage octal DTR data I/O transfers.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the (quad) program load macro name.
While at modifying it, better add the missing_ OP suffix to align with
all the other macros of the same kind.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the (single) program load macro name.
While at modifying it, better add the missing_ OP suffix to align with
all the other macros of the same kind.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the program execution macro name.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[Miquel: Fixed conflicts with -next by updating esmt and micron drivers]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (quad IO) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (quad output) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (dual IO) read from cache macro names. While at
modifying them, better reordering the macros to group them all by bus
topology which now feels more intuitive.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (dual output) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (single) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the page read macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the erase macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the get/set feature macro names.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[Miquel: Fixed conflicts with -next by updating macronix driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the read ID macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the write enable/disable macro names.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[Miquel: Fixed conflicts with -next by updating esmt and micron drivers]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
vendor naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the reset macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
__VA_OPT__ is a macro that is useful when some arguments can be present
or not to entirely skip some part of a definition. Unfortunately, it
is a too recent addition that some of the still supported old GCC
versions do not know about, and is anyway not part of C11 that is the
version used in the kernel.
Find a trick to remove this macro, typically '__VA_ARGS__ + 0' is a
workaround used in netlink.h which works very well here, as we either
expect:
- 0
- A positive value
- No value, which means the field should be 0.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503181330.YcDXGy7F-lkp@intel.com/
Fixes: 7ce0d16d5802 ("mtd: spinand: Add an optional frequency to read from cache macros")
Cc: stable@vger.kernel.org
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's assume all these macros should not have a trailing comma, this way
the caller can use a more formal and usual C writing style, as reflected
in the Macronix driver.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
When the host ECC fails to correct the data error of NAND device,
there's a special read for data recovery method which can be setup
by the host for the next read. There are several retry levels that
can be attempted until the lost data is recovered or definitely
assumed lost.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The global functions spinand_otp_read() and spinand_otp_write() have
been introduced. Since most SPI-NAND flashes read/write OTP in the same
way, let's define global functions to avoid code duplication.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Change the functions spinand_wait() and spinand_otp_page_size() from
static to global so that SPI NAND flash drivers don't duplicate it.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The MTD subsystem already supports accessing two OTP areas: user and
factory. User areas can be written by the user.
This patch provides the SPINAND_FACT_OTP_INFO and SPINAND_USER_OTP_INFO
macros to add parameters to spinand_info.
To implement OTP operations, the client (flash driver) is provided with
callbacks for user area:
.read(), .write(), .info(), .lock(), .erase();
and for factory area:
.read(), .info();
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Change these functions from static to global so that to use them later
in OTP operations. Since reading OTP pages is no different from reading
pages from the main area.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Advanced SPI-NAND chips are capable of reading data much faster by
leveraging DTR support. This support extends to dual and quad
configurations.
Create macros defining all possible read from cache DTR variants:
- SPINAND_PAGE_READ_FROM_CACHE_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_X2_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_X4_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_DUALIO_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_QUADIO_DTR_OP
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
While the SPINAND_PAGE_READ_FROM_CACHE_FAST_OP macro is supposed to be
able to run at the flash highest supported frequency, it is not the case
of the regular read from cache, which may be limited in terms of maximum
frequency. Add an optional argument to this macro, which will be used to
set the maximum frequency, if any.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
So far, the SPINAND_PAGE_READ_FROM_CACHE_OP macro was taking a first
argument, "fast", which was inducing the possibility to support higher
bus frequencies than with the normal (slower) read from cache
alternative. In practice, without frequency change on the bus, this was
likely without effect, besides perhaps allowing another variant of the
same command, that could run at the default highest speed. If we want to
support this fully, we need to add a frequency parameter to the slowest
command. But before we do that, let's drop the "fast" boolean from the
macro and duplicate it, this will further help supporting having
different frequencies allowed for each variant.
The change is also of course propagated to all users. It has the nice
effect to have all macros aligned on the same pattern.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SkyHigh S35ML01G300, S35ML01G301, S35ML02G300, and S35ML04G300 are 1Gb,
2Gb, and 4Gb SLC SPI NAND flash family. This family of devices has
on-die ECC which parity bits are stored to hidden area. In this family
the on-die ECC cannot be disabled so raw access needs to be prevented.
Link: https://www.skyhighmemory.com/download/SPI_S35ML01_04G3_002_19205.pdf?v=P
Co-developed-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SkyHigh spinand device has ECC enable bit in configuration register but
it must be always enabled. If ECC is disabled, read and write ops
results in undetermined state. For such devices, a way to avoid raw
access is needed.
Introduce SPINAND_NO_RAW_ACCESS flag to advertise the device does not
support raw access. In such devices, the on-die ECC engine ops returns
error to I/O request in raw mode.
Checking and marking BBM need to be cared as special case, by adding
fallback mechanism that tries read/write OOB with ECC enabled.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add two flags for inserting the Plane Select bit into the column
address during the write_to_cache and the read_from_cache operation.
Add the SPINAND_HAS_PROG_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the write_to_cache operation.
Add the SPINAND_HAS_READ_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the read_from_cache operation.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240909092643.2434479-2-linchengming884@gmail.com
|
|
This helper function will soon be used from a vendor driver, let's
export it through the spinand.h header. No need for any export, as there
is currently no reason for any module to need it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-6-miquel.raynal@bootlin.com
|
|
A regular page read consist in:
- Asking one page of content from the NAND array to be loaded in the
chip's SRAM,
- Waiting for the operation to be done,
- Retrieving the data (I/O phase) from the chip's SRAM.
When reading several sequential pages, the above operation is repeated
over and over. There is however a way to optimize these accesses, by
enabling continuous reads. The feature requires the NAND chip to have a
second internal SRAM area plus a bit of additional internal logic to
trigger another internal transfer between the NAND array and the second
SRAM area while the I/O phase is ongoing. Once the first I/O phase is
done, the host can continue reading more data, continuously, as the chip
will automatically switch to the second SRAM content (which has already
been loaded) and in turns trigger the next load into the first SRAM area
again.
From an instruction perspective, the command op-codes are different, but
the same cycles are required. The only difference is that after a
continuous read (which is stopped by a CS deassert), the host must
observe a delay of tRST. However, because there is no guarantee in Linux
regarding the actual state of the CS pin after a transfer (in order to
speed-up the next transfer if targeting the same device), it was
necessary to manually end the continuous read with a configuration
register write operation.
Continuous reads have two main drawbacks:
* They only work on full pages (column address ignored)
* Only the main data area is pulled, out-of-band bytes are not
accessible. Said otherwise, the feature can only be useful with on-die
ECC engines.
Performance wise, measures have been performed on a Zynq platform using
Macronix SPI-NAND controller with a Macronix chip (based on the
flash_speed tool modified for testing sequential reads):
- 1-1-1 mode: performances improved from +3% (2-pages) up to +10% after
a dozen pages.
- 1-1-4 mode: performances improved from +15% (2-pages) up to +40% after
a dozen pages.
This series is based on a previous work from Macronix engineer Jaime
Liao.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-5-miquel.raynal@bootlin.com
|
|
E.g. ESMT chips will return an identification code with a length of 5
bytes. In order to prevent ambiguity, flash chips would actually need to
return IDs that are up to 17 or more bytes long due to JEDEC's
continuation scheme. I understand that if a manufacturer ID is located
in bank N of JEDEC's database (there are currently 16 banks), N - 1
continuation codes (7Fh) need to be added to the identification code
(comprising of manufacturer ID and device ID). However, most flash chip
manufacturers don't seem to implement this (correctly).
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Tested-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240125200108.24374-2-ezra@easyb.ch
|
|
Add support for FORESEE F35SQA002G SPI NAND.
Datasheet:
https://www.longsys.com/uploads/LM-00006FORESEEF35SQA002GDatasheet_1650183701.pdf
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231002140458.147605-1-mmkurbanov@salutedevices.com
|
|
This patch adds support for ESMT F50L1G41LB and F50D1G41LB.
It seems that ESMT likes to use random JEDEC ID from other vendors.
Their 1G chips uses 0xc8 from GigaDevice and 2G/4G chips uses 0x2c from
Micron. For this reason, the ESMT entry is named esmt_c8 with explicit
JEDEC ID in variable name.
Datasheets:
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F50L1G41LB(2M).pdf
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F50D1G41LB(2M).pdf
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Tested-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230329114240.378722-1-mmkurbanov@sberdevices.ru
|
|
Add support for AllianceMemory AS5F34G04SND SPI NAND flash
Datasheet:
- https://www.alliancememory.com/wp-content/uploads/pdf/flash/AllianceMemory_SPI_NAND_Flash_July2020_Rev1.0.pdf
Signed-off-by: Mario Kicherer <dev@kicherer.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230126144050.2656358-1-dev@kicherer.org
|
|
Add support for the ATO25D1GA SPI NAND flash.
Datasheet:
- https://atta.szlcsc.com/upload/public/pdf/source/20191212/C469320_04599D67B03B078044EB65FF5AEDDDE9.pdf
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220604113250.4745-1-aidanmacdonald.0x0@gmail.com
|
|
Add support for XTX Technology XT26G01AXXXXX, XTX26G02AXXXXX and
XTX26G04AXXXXX SPI NAND.
These are 3V, 1G/2G/4Gbit serial SLC NAND flash devices with on-die ECC
(8bit strength per 512bytes).
Tested on Teltonika RUTX10 flashed with OpenWrt.
Links:
- http://www.xtxtech.com/download/?AId=225
- https://datasheet.lcsc.com/szlcsc/2005251034_XTX-XT26G01AWSEGA_C558841.pdf
Signed-off-by: Felix Matouschek <felix@matouschek.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220418132803.664103-1-felix@matouschek.org
|
|
In order for pipelined ECC engines to be able to enable/disable the ECC
engine only when needed and avoid races when future parallel-operations
will be supported, we need to provide the information about the use of
the ECC engine in the direct mapping hooks. As direct mapping
configurations are meant to be static, it is best to create two new
mappings: one for regular 'raw' accesses and one for accesses involving
correction. It is up to the driver to use or not the new ECC enable
boolean contained in the spi-mem operation.
As dirmaps are not free (they consume a few pages of MMIO address space)
and because these extra entries are only meant to be used by pipelined
engines, let's limit their use to this specific type of engine and save
a bit of memory with all the other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-9-miquel.raynal@bootlin.com
|
|
Make use of spi-mem poll status APIs to let advanced controllers
optimize wait operations.
This should also fix the high CPU usage for system that don't have
a dedicated STATUS poll block logic.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210518162754.15940-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make use of the existing functions taken from the SPI-NAND core to
instantiate an on-die ECC engine specific to the SPI-NAND core. The
next step will be to tweak the core to use this object instead of
calling the helpers directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-4-miquel.raynal@bootlin.com
|
|
Prepare the migration to a generic ECC engine by renaming the
nand_ecc_req structure into nand_ecc_props. This structure will be the
base of a wider 'nand_ecc' structure.
In nand_device, these properties are still named "eccreq" even if
"eccprops" might be more descriptive. This is just a transition step,
this field is being replaced very soon by a much wider structure. The
impact of renaming this field would be huge compared to its interest.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529002517.3546-14-miquel.raynal@bootlin.com
|
|
Add SPINAND_HAS_CR_FEAT_BIT flag to identify the SPI NAND device with
the Continuous Read mode.
Some of the Micron SPI NAND devices have the "Continuous Read" feature
enabled by default, which does not fit the subsystem needs.
In this mode, the READ CACHE command doesn't require the starting column
address. The device always output the data starting from the first
column of the cache register, and once the end of the cache register
reached, the data output continues through the next page. With the
continuous read mode, it is possible to read out the entire block using
a single READ command, and once the end of the block reached, the output
pins become High-Z state. However, during this mode the read command
doesn't output the OOB area.
Hence, we disable the feature at probe time.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-5-sshivamurthy@micron.com
|
|
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
Tested on GD5F1GQ4UAYIG and W25N01GVZEIG.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200208074439.146296-1-gch981213@gmail.com
|
|
Add initial support for Paragon Technology
PN26G01Axxxxx and PN26G02Axxxxx SPI NAND
Datasheets available at
http://www.xtxtech.com/upfile/2016082517274590.pdf
http://www.xtxtech.com/upfile/2016082517282329.pdf
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The GigaDevice GD5F1GQ4UFxxG SPI NAND utilizes two-byte device IDs.
http://www.gigadevice.com/datasheet/gd5f1gq4xfxxg/
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
