| Age | Commit message (Collapse) | Author |
|---|
|
requested
Symmetric RSS hash requires that:
* No other fields besides IP src/dst and/or L4 src/dst are set
* If src is set, dst must also be set
This restriction was only enforced when RXNFC was configured after
symmetric hash was enabled. In the opposite order of operations (RXNFC
then symmetric enablement) the check was not performed.
Perform the sanity check on set_rxfh as well, by iterating over all flow
types hash fields and making sure they are all symmetric.
Introduce a function that returns whether a flow type is hashable (not
spec only) and needs to be iterated over. To make sure that no one
forgets to update the list of hashable flow types when adding new flow
types, a static assert is added to draw the developer's attention.
The conversion of uapi #defines to enum is not ideal, but as Jakub
mentioned [1], we have precedent for that.
[1] https://lore.kernel.org/netdev/20250324073509.6571ade3@kernel.org/
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250508103034.885536-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an additional type of symmetric RSS hash type: OR-XOR.
The "Symmetric-OR-XOR" algorithm transforms the input as follows:
(SRC_IP | DST_IP, SRC_IP ^ DST_IP, SRC_PORT | DST_PORT, SRC_PORT ^ DST_PORT)
Change 'cap_rss_sym_xor_supported' to 'supported_input_xfrm', a bitmap
of supported RXH_XFRM_* types.
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250224174416.499070-2-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc3).
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the netlink type for hardware timestamp flags, which are represented
as a bitset of flags. Although only one flag is supported currently, the
correct netlink bitset type should be used instead of u32 to keep
consistency with other fields. Address this by adding a new named string
set description for the hwtstamp flag structure.
The code has been introduced in the current release so the uAPI change is
still okay.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Fixes: 6e9e2eed4f39 ("net: ethtool: Add support for tsconfig command to get/set hwtstamp config")
Link: https://patch.msgid.link/20250205110304.375086-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define 200G, 400G and 800G link modes using 200Gbps per lane.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce a new way to report PHY statistics in a structured and
standardized format using the netlink API. This new method does not
replace the old driver-specific stats, which can still be accessed with
`ethtool -S <eth name>`. The structured stats are available with
`ethtool -S <eth name> --all-groups`.
This new method makes it easier to diagnose problems by organizing stats
in a consistent and documented way.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
struct ethtool_link_settings tends to be used as a header for other
structures that have trailing bytes[1], but has a trailing flexible array
itself. Using this overlapped with other structures leads to ambiguous
object sizing in the compiler, so we want to avoid such situations (which
have caused real bugs in the past). Detecting this can be done with
-Wflex-array-member-not-at-end, which will need to be enabled globally.
Using a tagged struct_group() to create a new ethtool_link_settings_hdr
structure isn't possible as it seems we cannot use the tagged variant of
struct_group() due to syntax issues from C++'s perspective (even within
"extern C")[2]. Instead, we can just leave the offending member defined
in UAPI and remove it from the kernel's view of the structure, as Linux
doesn't actually use this member at all. There is also no change in
size since it was already a flexible array that didn't contribute to
size returned by any use of sizeof().
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/lkml/20241109100213.262a2fa0@kernel.org/ [2]
Link: https://lore.kernel.org/lkml/0bc2809fe2a6c11dd4c8a9a10d9bd65cccdb559b.1730238285.git.gustavoars@kernel.org/ [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20241115204308.3821419-3-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 43d3487035e9a86fad952de4240a518614240d43. We cannot
use tagged struct groups in UAPI because C++ will throw syntax errors
even under "extern C".
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20241115204308.3821419-2-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the `__struct_group()` helper to create a new tagged
`struct ethtool_link_settings_hdr`. This structure groups together
all the members of the flexible `struct ethtool_link_settings`
except the flexible array. As a result, the array is effectively
separated from the rest of the members without modifying the memory
layout of the flexible structure.
This new tagged struct will be used to fix problematic declarations
of middle-flex-arrays in composite structs[1].
[1] https://git.kernel.org/linus/d88cabfd9abc
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/9e9fb0bd72e5ba1e916acbb4995b1e358b86a689.1730238285.git.gustavoars@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new link mode necessary for 10 MBit single-pair
connection in BroadR-Reach mode on bcm5481x PHY by Broadcom.
This new link mode, 10baseT1BRR, is known as 1BR10 in the Broadcom
terminology. Another link mode to be used is 1BR100 and it is already
present as 100baseT1, because Broadcom's 1BR100 became 100baseT1
(IEEE 802.3bw).
Signed-off-by: Kamil Horák (2N) <kamilh@axis.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240712150709.3134474-2-kamilh@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This update expands the status information provided by ethtool for PSE c33.
It includes details such as the detected class, current power delivered,
and extended state information.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240704-feature_poe_power_cap-v6-1-320003204264@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.3.1 of revision 5.2 of
the CMIS standard.
Add a pair of new ethtool messages that allow:
* User space to trigger firmware update of transceiver modules
* The kernel to notify user space about the progress of the process
The user interface is designed to be asynchronous in order to avoid
RTNL being held for too long and to allow several modules to be
updated simultaneously. The interface is designed with CMIS compliant
modules in mind, but kept generic enough to accommodate future use
cases, if these arise.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The series is causing issues with PHY drivers built as modules.
Since it was only partially applied and the merge window has
opened let's revert and try again for v6.11.
Revert 6916e461e793 ("net: phy: Introduce ethernet link topology representation")
Revert 0ec5ed6c130e ("net: sfp: pass the phy_device when disconnecting an sfp module's PHY")
Revert e75e4e074c44 ("net: phy: add helpers to handle sfp phy connect/disconnect")
Revert fdd353965b52 ("net: sfp: Add helper to return the SFP bus name")
Revert 841942bc6212 ("net: ethtool: Allow passing a phy index for some commands")
Link: https://lore.kernel.org/all/171242462917.4000.9759453824684907063.git-patchwork-notify@kernel.org/
Link: https://lore.kernel.org/all/20240507102822.2023826-1-maxime.chevallier@bootlin.com/
Link: https://lore.kernel.org/r/20240513154156.104281-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce an enumeration to define PSE types (C33 or PoDL),
utilizing a bitfield for potential future support of both types.
Include 'pse_get_types' helper for external access to PSE type info.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-2-242293fd1900@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the current PSE interface for Ethernet Power Equipment, support is
limited to PoDL. This patch extends the interface to accommodate the
objects specified in IEEE 802.3-2022 145.2 for Power sourcing
Equipment (PSE).
The following objects are now supported and considered mandatory:
- IEEE 802.3-2022 30.9.1.1.5 aPSEPowerDetectionStatus
- IEEE 802.3-2022 30.9.1.1.2 aPSEAdminState
- IEEE 802.3-2022 30.9.1.2.1 aPSEAdminControl
To avoid confusion between "PoDL PSE" and "PoE PSE", which have similar
names but distinct values, we have followed the suggestion of Oleksij
Rempel and Andrew Lunn to maintain separate naming schemes for each,
using c33 (clause 33) prefix for "PoE PSE".
You can find more details in the discussion threads here:
https://lore.kernel.org/netdev/20230912110637.GI780075@pengutronix.de/
https://lore.kernel.org/netdev/2539b109-72ad-470a-9dae-9f53de4f64ec@lunn.ch/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-1-242293fd1900@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a patch that enables RSS functionality for GTP packets using ethtool.
A user can include TEID and make RSS work for GTP-U over IPv4 by doing the
following:`ethtool -N ens3 rx-flow-hash gtpu4 sde`
In addition to gtpu(4|6), we now support gtpc(4|6),gtpc(4|6)t,gtpu(4|6)e,
gtpu(4|6)u, and gtpu(4|6)d.
gtpc(4|6): Used for GTP-C in IPv4 and IPv6, where the GTP header format does
not include a TEID.
gtpc(4|6)t: Used for GTP-C in IPv4 and IPv6, with a GTP header format that
includes a TEID.
gtpu(4|6): Used for GTP-U in both IPv4 and IPv6 scenarios.
gtpu(4|6)e: Used for GTP-U with extended headers in both IPv4 and IPv6.
gtpu(4|6)u: Used when the PSC (PDU session container) in the GTP-U extended
header includes Uplink, applicable to both IPv4 and IPv6.
gtpu(4|6)d: Used when the PSC in the GTP-U extended header includes Downlink,
for both IPv4 and IPv6.
GTP generates a flow that includes an ID called TEID to identify the tunnel.
This tunnel is created for each UE (User Equipment).By performing RSS based on
this flow, it is possible to apply RSS for each communication unit from the UE.
Without this, RSS would only be effective within the range of IP addresses. For
instance, the PGW can only perform RSS within the IP range of the SGW.
Problematic from a load distribution perspective, especially if there's a bias
in the terminals connected to a particular base station.This case can be
solved by using this patch.
Signed-off-by: Takeru Hayasaka <hayatake396@gmail.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This reverts commit 32bb4515e34469975abc936deb0a116c4a445817.
This reverts commit d078d480639a4f3b5fc2d56247afa38e0956483a.
This reverts commit fcc4b105caa4b844bf043375bf799c20a9c99db1.
This reverts commit 345237dbc1bdbb274c9fb9ec38976261ff4a40b8.
This reverts commit 7db69ec9cfb8b4ab50420262631fb2d1908b25bf.
This reverts commit 95132a018f00f5dad38bdcfd4180d1af955d46f6.
This reverts commit 63d5eaf35ac36cad00cfb3809d794ef0078c822b.
This reverts commit c29451aefcb42359905d18678de38e52eccb3bb5.
This reverts commit 2ab0edb505faa9ac90dee1732571390f074e8113.
This reverts commit dedd702a35793ab462fce4c737eeba0badf9718e.
This reverts commit 034fcc210349b873ece7356905be5c6ca11eef2a.
This reverts commit 9c5625f559ad6fe9f6f733c11475bf470e637d34.
This reverts commit 02018c544ef113e980a2349eba89003d6f399d22.
Looks like we need more time for reviews, and incremental
changes will be hard to make sense of. So revert.
Link: https://lore.kernel.org/all/ZZP6FV5sXEf+xd58@shell.armlinux.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a NO_CHANGE uAPI value for the new RXFH/RSS input_xfrm uAPI field.
This needed so that user-space can set other RSS values (hkey or indir
table) without affecting input_xfrm.
Should have been part of [1].
Link: https://lore.kernel.org/netdev/20231213003321.605376-1-ahmed.zaki@intel.com/ [1]
Fixes: 13e59344fb9d ("net: ethtool: add support for symmetric-xor RSS hash")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231221184235.9192-3-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel doc comments for struct ethtool_link_settings includes
documentation for three fields that were never present there, leading to
these docs-build warnings:
./include/uapi/linux/ethtool.h:2207: warning: Excess struct member 'supported' description in 'ethtool_link_settings'
./include/uapi/linux/ethtool.h:2207: warning: Excess struct member 'advertising' description in 'ethtool_link_settings'
./include/uapi/linux/ethtool.h:2207: warning: Excess struct member 'lp_advertising' description in 'ethtool_link_settings'
Remove the entries to make the warnings go away. There was some
information there on how data in >link_mode_masks is formatted; move that
to the body of the comment to preserve it.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Symmetric RSS hash functions are beneficial in applications that monitor
both Tx and Rx packets of the same flow (IDS, software firewalls, ..etc).
Getting all traffic of the same flow on the same RX queue results in
higher CPU cache efficiency.
A NIC that supports "symmetric-xor" can achieve this RSS hash symmetry
by XORing the source and destination fields and pass the values to the
RSS hash algorithm.
The user may request RSS hash symmetry for a specific algorithm, via:
# ethtool -X eth0 hfunc <hash_alg> symmetric-xor
or turn symmetry off (asymmetric) by:
# ethtool -X eth0 hfunc <hash_alg>
The specific fields for each flow type should then be specified as usual
via:
# ethtool -N|-U eth0 rx-flow-hash <flow_type> s|d|f|n
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-4-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IEEE 802.3-2018 clause 99 defines a MAC Merge sublayer which contains an
Express MAC and a Preemptible MAC. Both MACs are hidden to higher and
lower layers and visible as a single MAC (packet classification to eMAC
or pMAC on TX is done based on priority; classification on RX is done
based on SFD).
For devices which support a MAC Merge sublayer, it is desirable to
retrieve individual packet counters from the eMAC and the pMAC, as well
as aggregate statistics (their sum).
Introduce a new ETHTOOL_A_STATS_SRC attribute which is part of the
policy of ETHTOOL_MSG_STATS_GET and, and an ETHTOOL_A_PAUSE_STATS_SRC
which is part of the policy of ETHTOOL_MSG_PAUSE_GET (accepted when
ETHTOOL_FLAG_STATS is set in the common ethtool header). Both of these
take values from enum ethtool_mac_stats_src, defaulting to "aggregate"
in the absence of the attribute.
Existing drivers do not need to pay attention to this enum which was
added to all driver-facing structures, just the ones which report the
MAC merge layer as supported.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC merge sublayer (IEEE 802.3-2018 clause 99) is one of 2
specifications (the other being Frame Preemption; IEEE 802.1Q-2018
clause 6.7.2), which work together to minimize latency caused by frame
interference at TX. The overall goal of TSN is for normal traffic and
traffic with a bounded deadline to be able to cohabitate on the same L2
network and not bother each other too much.
The standards achieve this (partly) by introducing the concept of
preemptible traffic, i.e. Ethernet frames that have a custom value for
the Start-of-Frame-Delimiter (SFD), and these frames can be fragmented
and reassembled at L2 on a link-local basis. The non-preemptible frames
are called express traffic, they are transmitted using a normal SFD, and
they can preempt preemptible frames, therefore having lower latency,
which can matter at lower (100 Mbps) link speeds, or at high MTUs (jumbo
frames around 9K). Preemption is not recursive, i.e. a P frame cannot
preempt another P frame. Preemption also does not depend upon priority,
or otherwise said, an E frame with prio 0 will still preempt a P frame
with prio 7.
In terms of implementation, the standards talk about the presence of an
express MAC (eMAC) which handles express traffic, and a preemptible MAC
(pMAC) which handles preemptible traffic, and these MACs are multiplexed
on the same MII by a MAC merge layer.
To support frame preemption, the definition of the SFD was generalized
to SMD (Start-of-mPacket-Delimiter), where an mPacket is essentially an
Ethernet frame fragment, or a complete frame. Stations unaware of an SMD
value different from the standard SFD will treat P frames as error
frames. To prevent that from happening, a negotiation process is
defined.
On RX, packets are dispatched to the eMAC or pMAC after being filtered
by their SMD. On TX, the eMAC/pMAC classification decision is taken by
the 802.1Q spec, based on packet priority (each of the 8 user priority
values may have an admin-status of preemptible or express).
The MAC Merge layer and the Frame Preemption parameters have some degree
of independence in terms of how software stacks are supposed to deal
with them. The activation of the MM layer is supposed to be controlled
by an LLDP daemon (after it has been communicated that the link partner
also supports it), after which a (hardware-based or not) verification
handshake takes place, before actually enabling the feature. So the
process is intended to be relatively plug-and-play. Whereas FP settings
are supposed to be coordinated across a network using something
approximating NETCONF.
The support contained here is exclusively for the 802.3 (MAC Merge)
portions and not for the 802.1Q (Frame Preemption) parts. This API is
sufficient for an LLDP daemon to do its job. The FP adminStatus variable
from 802.1Q is outside the scope of an LLDP daemon.
I have taken a few creative licenses and augmented the Linux kernel UAPI
compared to the standard managed objects recommended by IEEE 802.3.
These are:
- ETHTOOL_A_MM_PMAC_ENABLED: According to Figure 99-6: Receive
Processing state diagram, a MAC Merge layer is always supposed to be
able to receive P frames. However, this implies keeping the pMAC
powered on, which will consume needless power in applications where FP
will never be used. If LLDP is used, the reception of an Additional
Ethernet Capabilities TLV from the link partner is sufficient
indication that the pMAC should be enabled. So my proposal is that in
Linux, we keep the pMAC turned off by default and that user space
turns it on when needed.
- ETHTOOL_A_MM_VERIFY_ENABLED: The IEEE managed object is called
aMACMergeVerifyDisableTx. I opted for consistency (positive logic) in
the boolean netlink attributes offered, so this is also positive here.
Other than the meaning being reversed, they correspond to the same
thing.
- ETHTOOL_A_MM_MAX_VERIFY_TIME: I found it most reasonable for a LLDP
daemon to maximize the verifyTime variable (delay between SMD-V
transmissions), to maximize its chances that the LP replies. IEEE says
that the verifyTime can range between 1 and 128 ms, but the NXP ENETC
stupidly keeps this variable in a 7 bit register, so the maximum
supported value is 127 ms. I could have chosen to hardcode this in the
LLDP daemon to a lower value, but why not let the kernel expose its
supported range directly.
- ETHTOOL_A_MM_TX_MIN_FRAG_SIZE: the standard managed object is called
aMACMergeAddFragSize, and expresses the "additional" fragment size
(on top of ETH_ZLEN), whereas this expresses the absolute value of the
fragment size.
- ETHTOOL_A_MM_RX_MIN_FRAG_SIZE: there doesn't appear to exist a managed
object mandated by the standard, but user space clearly needs to know
what is the minimum supported fragment size of our local receiver,
since LLDP must advertise a value no lower than that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Zero-length arrays are deprecated[1]. Replace struct ethtool_rxnfc's
"rule_locs" 0-length array with a flexible array. Detected with GCC 13,
using -fstrict-flex-arrays=3:
net/ethtool/common.c: In function 'ethtool_get_max_rxnfc_channel':
net/ethtool/common.c:558:55: warning: array subscript i is outside array bounds of '__u32[0]' {aka 'unsigned int[]'} [-Warray-bounds=]
558 | .fs.location = info->rule_locs[i],
| ~~~~~~~~~~~~~~~^~~
In file included from include/linux/ethtool.h:19,
from include/uapi/linux/ethtool_netlink.h:12,
from include/linux/ethtool_netlink.h:6,
from net/ethtool/common.c:3:
include/uapi/linux/ethtool.h:1186:41: note: while referencing
'rule_locs'
1186 | __u32 rule_locs[0];
| ^~~~~~~~~
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: kernel test robot <lkp@intel.com>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230106042844.give.885-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Many of the drivers which implement ethtool_ops::get_drvinfo() will
prints the .driver, .version or .bus_info of struct ethtool_drvinfo.
To have a glance of current state, do:
$ git grep -W "get_drvinfo(struct"
Printing in those three fields is useless because:
- since [1], the driver version should be the kernel version (at
least for upstream drivers). Arguably, out of tree drivers might
still want to set a custom version, but out of tree is not our
focus.
- since [2], the core is able to provide default values for .driver
and .bus_info.
In summary, drivers may provide .fw_version and .erom_version, the
rest is expected to be done by the core.
In struct ethtool_ops doc from linux/ethtool: rephrase field
get_drvinfo() doc to discourage developers from implementing this
callback.
In struct ethtool_drvinfo doc from uapi/linux/ethtool.h: remove the
paragraph mentioning what drivers should do. Rationale: no need to
repeat what is already written in struct ethtool_ops doc. But add a
note that .fw_version and .erom_version are driver defined.
Also update the dummy driver and simply remove the callback in order
not to confuse the newcomers: most of the drivers will not need this
callback function any more.
[1] commit 6a7e25c7fb48 ("net/core: Replace driver version to be
kernel version")
Link: https://git.kernel.org/torvalds/linux/c/6a7e25c7fb48
[2] commit edaf5df22cb8 ("ethtool: ethtool_get_drvinfo: populate
drvinfo fields even if callback exits")
Link: https://git.kernel.org/netdev/net-next/c/edaf5df22cb8
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20221116171828.4093-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for 800Gbps speed, link modes of 100Gbps per lane.
As mentioned in slide 21 in IEEE documentation [1], all adopted 802.3df
copper and optical PMDs baselines using 100G/lane will be supported.
Add the relevant PMDs which are mentioned in slide 5 in IEEE
documentation [1] and were approved on 10-2022 [2]:
BP - KR8
Cu Cable - CR8
MMF 50m - VR8
MMF 100m - SR8
SMF 500m - DR8
SMF 2km - DR8-2
[1]: https://www.ieee802.org/3/df/public/22_10/22_1004/shrikhande_3df_01a_221004.pdf
[2]: https://ieee802.org/3/df/KeyMotions_3df_221005.pdf
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add interface to support Power Sourcing Equipment. At current step it
provides generic way to address all variants of PSE devices as defined
in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4
PoDL Power Sourcing Equipment (PSE).
Currently supported and mandatory objects are:
IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus
IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState
IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl
This is minimal interface needed to control PSE on each separate
ethernet port but it provides not all mandatory objects specified in
IEEE 802.3-2018.
Since "PoDL PSE" and "PSE" have similar names, but some different values
I decide to not merge them and keep separate naming schema. This should
allow as to be as close to IEEE 802.3 spec as possible and avoid name
conflicts in the future.
This implementation is connected to PHYs instead of MACs because PSE
auto classification can potentially interfere with PHY auto negotiation.
So, may be some extra PHY related initialization will be needed.
With WIP version of ethtools interaction with PSE capable link looks
as following:
$ ip l
...
5: t1l1@eth0: <BROADCAST,MULTICAST> ..
...
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: disabled
PoDL PSE Power Detection Status: disabled
$ ethtool --set-pse t1l1 podl-pse-admin-control enable
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: enabled
PoDL PSE Power Detection Status: delivering power
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
This code was transformed with the help of Coccinelle:
(linux-5.19-rc2$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)
@@
identifier S, member, array;
type T1, T2;
@@
struct S {
...
T1 member;
T2 array[
- 0
];
};
-fstrict-flex-arrays=3 is coming and we need to land these changes
to prevent issues like these in the short future:
../fs/minix/dir.c:337:3: warning: 'strcpy' will always overflow; destination buffer has size 0,
but the source string has length 2 (including NUL byte) [-Wfortify-source]
strcpy(de3->name, ".");
^
Since these are all [0] to [] changes, the risk to UAPI is nearly zero. If
this breaks anything, we can use a union with a new member name.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/78
Build-tested-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/62b675ec.wKX6AOZ6cbE71vtF%25lkp@intel.com/
Acked-by: Dan Williams <dan.j.williams@intel.com> # For ndctl.h
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for ethtool to set/get tx copybreak buf size.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an extended state and sub-state to describe link issues related to
transceiver modules.
The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state
tells user space that port is unable to gain a carrier because the CMIS
Module State Machine did not reach the ModuleReady (Fully Operational)
state. For example, if the module is stuck at ModuleLowPwr or
ModuleFault state. In case of the latter, user space can read the fault
reason from the module's EEPROM and potentially reset it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST means the input
external clock signal for SerDes is too weak or lost.
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS means the received signal for
SerDes is too weak because analog loss of signal.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Th_strings arrays netdev_features_strings, tunable_strings, and
phy_tunable_strings has been moved to file net/ethtool/common.c.
So fixes the comment.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most devices maintain RMON (RFC 2819) stats - particularly
the "histogram" of packets received by size. Unlike other
RFCs which duplicate IEEE stats, the short/oversized frame
counters in RMON don't seem to match IEEE stats 1-to-1 either,
so expose those, too. Do not expose basic packet, CRC errors
etc - those are already otherwise covered.
Because standard defines packet ranges only up to 1518, and
everything above that should theoretically be "oversized"
- devices often create their own ranges.
Going beyond what the RFC defines - expose the "histogram"
in the Tx direction (assume for now that the ranges will
be the same).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Number of devices maintains the standard-based MAC control
counters for control frames. Add a API for those.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the MAC statistics are included in
struct rtnl_link_stats64, but some fields
are aggregated. Besides it's good to expose
these clearly hardware stats separately.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an interface for reading standard stats, including
stats which don't have a corresponding control interface.
Start with IEEE 802.3 PHY stats. There seems to be only
one stat to expose there.
Define API to not require user space changes when new
stats or groups are added. Groups are based on bitset,
stats have a string set associated.
v1: wrap stats in a nest
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix remaining issues with kdoc in the ethtool headers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a note on expected handling of reserved fields,
and references to all kdocs. This fixes a bunch
of kdoc warnings.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extended link state structures and enums use kdoc headers
but then do not describe any of the members.
Convert to normal comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kdoc does not have good support for documenting defines,
and we can't abuse the enum documentation because it
generates warnings.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct ethtool_fecparam::reserved can't be used in SET, because
ethtool user space doesn't zero-initialize the structure.
Make this clear.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The definition of the FEC driver interface is quite unclear.
Improve the documentation.
This is based on current driver and user space code, as well
as the discussions about the interface:
RFC v1 (24 Oct 2016): https://lore.kernel.org/netdev/1477363849-36517-1-git-send-email-vidya@cumulusnetworks.com/
- this version has the autoneg field
- no active_fec field
- none vs off confusion is already present
RFC v2 (10 Feb 2017): https://lore.kernel.org/netdev/1486727004-11316-1-git-send-email-vidya@cumulusnetworks.com/
- autoneg removed
- active_fec added
v1 (10 Feb 2017): https://lore.kernel.org/netdev/1486751311-42019-1-git-send-email-vidya@cumulusnetworks.com/
- no changes in the code
v1 (24 Jun 2017): https://lore.kernel.org/netdev/1498331985-8525-1-git-send-email-roopa@cumulusnetworks.com/
- include in tree user
v2 (27 Jul 2017): https://lore.kernel.org/netdev/1501199248-24695-1-git-send-email-roopa@cumulusnetworks.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct ethtool_fecparam::active_fec is a GET-only field,
all in-tree drivers correctly ignore it on SET. Clear
the field on SET to avoid any confusion. Again, we can't
reject non-zero now since ethtool user space does not
zero-init the param correctly.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
