diff options
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml | 1 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml | 1 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/soc/qcom/qcom,se-common-props.yaml | 26 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml | 1 | ||||
| -rw-r--r-- | drivers/firmware/qcom/qcom_scm.c | 119 | ||||
| -rw-r--r-- | drivers/firmware/qcom/qcom_scm.h | 7 | ||||
| -rw-r--r-- | drivers/firmware/qcom/qcom_tzmem.c | 63 | ||||
| -rw-r--r-- | drivers/i2c/busses/i2c-qcom-geni.c | 8 | ||||
| -rw-r--r-- | drivers/soc/qcom/qcom-geni-se.c | 506 | ||||
| -rw-r--r-- | drivers/spi/spi-geni-qcom.c | 6 | ||||
| -rw-r--r-- | drivers/tty/serial/qcom_geni_serial.c | 8 | ||||
| -rw-r--r-- | include/linux/firmware/qcom/qcom_scm.h | 6 | ||||
| -rw-r--r-- | include/linux/firmware/qcom/qcom_tzmem.h | 15 | ||||
| -rw-r--r-- | include/linux/soc/qcom/geni-se.h | 4 |
14 files changed, 739 insertions, 32 deletions
diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml b/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml index 9f66a3bb1f80..51534953a69c 100644 --- a/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml +++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml @@ -75,6 +75,7 @@ required: allOf: - $ref: /schemas/i2c/i2c-controller.yaml# + - $ref: /schemas/soc/qcom/qcom,se-common-props.yaml# - if: properties: compatible: diff --git a/Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml b/Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml index dd33794b3534..ed7b3909d87d 100644 --- a/Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml +++ b/Documentation/devicetree/bindings/serial/qcom,serial-geni-qcom.yaml @@ -12,6 +12,7 @@ maintainers: allOf: - $ref: /schemas/serial/serial.yaml# + - $ref: /schemas/soc/qcom/qcom,se-common-props.yaml# properties: compatible: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,se-common-props.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,se-common-props.yaml new file mode 100644 index 000000000000..6a34f05a07e8 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,se-common-props.yaml @@ -0,0 +1,26 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soc/qcom/qcom,se-common-props.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: QUP Peripheral-specific properties for I2C, SPI and SERIAL bus + +description: + The Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) is + a programmable module that supports a wide range of serial interfaces + such as UART, SPI, I2C, I3C, etc. This defines the common properties used + across QUP-supported peripherals. + +maintainers: + - Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com> + - Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com> + +properties: + qcom,enable-gsi-dma: + $ref: /schemas/types.yaml#/definitions/flag + description: + Configure the Serial Engine (SE) to transfer data in QCOM GPI DMA mode. + By default, FIFO mode (PIO/CPU DMA) will be selected. + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml index 2e20ca313ec1..d12c5a060ed0 100644 --- a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml +++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml @@ -25,6 +25,7 @@ description: allOf: - $ref: /schemas/spi/spi-controller.yaml# + - $ref: /schemas/soc/qcom/qcom,se-common-props.yaml# properties: compatible: diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c index 049c6effb0ec..e777b7cb9b12 100644 --- a/drivers/firmware/qcom/qcom_scm.c +++ b/drivers/firmware/qcom/qcom_scm.c @@ -2098,6 +2098,122 @@ static int qcom_scm_qseecom_init(struct qcom_scm *scm) #endif /* CONFIG_QCOM_QSEECOM */ /** + * qcom_scm_qtee_invoke_smc() - Invoke a QTEE object. + * @inbuf: start address of memory area used for inbound buffer. + * @inbuf_size: size of the memory area used for inbound buffer. + * @outbuf: start address of memory area used for outbound buffer. + * @outbuf_size: size of the memory area used for outbound buffer. + * @result: result of QTEE object invocation. + * @response_type: response type returned by QTEE. + * + * @response_type determines how the contents of @inbuf and @outbuf + * should be processed. + * + * Return: On success, return 0 or <0 on failure. + */ +int qcom_scm_qtee_invoke_smc(phys_addr_t inbuf, size_t inbuf_size, + phys_addr_t outbuf, size_t outbuf_size, + u64 *result, u64 *response_type) +{ + struct qcom_scm_desc desc = { + .svc = QCOM_SCM_SVC_SMCINVOKE, + .cmd = QCOM_SCM_SMCINVOKE_INVOKE, + .owner = ARM_SMCCC_OWNER_TRUSTED_OS, + .args[0] = inbuf, + .args[1] = inbuf_size, + .args[2] = outbuf, + .args[3] = outbuf_size, + .arginfo = QCOM_SCM_ARGS(4, QCOM_SCM_RW, QCOM_SCM_VAL, + QCOM_SCM_RW, QCOM_SCM_VAL), + }; + struct qcom_scm_res res; + int ret; + + ret = qcom_scm_call(__scm->dev, &desc, &res); + if (ret) + return ret; + + if (response_type) + *response_type = res.result[0]; + + if (result) + *result = res.result[1]; + + return 0; +} +EXPORT_SYMBOL(qcom_scm_qtee_invoke_smc); + +/** + * qcom_scm_qtee_callback_response() - Submit response for callback request. + * @buf: start address of memory area used for outbound buffer. + * @buf_size: size of the memory area used for outbound buffer. + * @result: Result of QTEE object invocation. + * @response_type: Response type returned by QTEE. + * + * @response_type determines how the contents of @buf should be processed. + * + * Return: On success, return 0 or <0 on failure. + */ +int qcom_scm_qtee_callback_response(phys_addr_t buf, size_t buf_size, + u64 *result, u64 *response_type) +{ + struct qcom_scm_desc desc = { + .svc = QCOM_SCM_SVC_SMCINVOKE, + .cmd = QCOM_SCM_SMCINVOKE_CB_RSP, + .owner = ARM_SMCCC_OWNER_TRUSTED_OS, + .args[0] = buf, + .args[1] = buf_size, + .arginfo = QCOM_SCM_ARGS(2, QCOM_SCM_RW, QCOM_SCM_VAL), + }; + struct qcom_scm_res res; + int ret; + + ret = qcom_scm_call(__scm->dev, &desc, &res); + if (ret) + return ret; + + if (response_type) + *response_type = res.result[0]; + + if (result) + *result = res.result[1]; + + return 0; +} +EXPORT_SYMBOL(qcom_scm_qtee_callback_response); + +static void qcom_scm_qtee_free(void *data) +{ + struct platform_device *qtee_dev = data; + + platform_device_unregister(qtee_dev); +} + +static void qcom_scm_qtee_init(struct qcom_scm *scm) +{ + struct platform_device *qtee_dev; + u64 result, response_type; + int ret; + + /* + * Probe for smcinvoke support. This will fail due to invalid buffers, + * but first, it checks whether the call is supported in QTEE syscall + * handler. If it is not supported, -EIO is returned. + */ + ret = qcom_scm_qtee_invoke_smc(0, 0, 0, 0, &result, &response_type); + if (ret == -EIO) + return; + + /* Setup QTEE interface device. */ + qtee_dev = platform_device_register_data(scm->dev, "qcomtee", + PLATFORM_DEVID_NONE, NULL, 0); + if (IS_ERR(qtee_dev)) + return; + + devm_add_action_or_reset(scm->dev, qcom_scm_qtee_free, qtee_dev); +} + +/** * qcom_scm_is_available() - Checks if SCM is available */ bool qcom_scm_is_available(void) @@ -2329,6 +2445,9 @@ static int qcom_scm_probe(struct platform_device *pdev) ret = qcom_scm_qseecom_init(scm); WARN(ret < 0, "failed to initialize qseecom: %d\n", ret); + /* Initialize the QTEE object interface. */ + qcom_scm_qtee_init(scm); + return 0; } diff --git a/drivers/firmware/qcom/qcom_scm.h b/drivers/firmware/qcom/qcom_scm.h index 0e8dd838099e..a56c8212cc0c 100644 --- a/drivers/firmware/qcom/qcom_scm.h +++ b/drivers/firmware/qcom/qcom_scm.h @@ -156,6 +156,13 @@ int qcom_scm_shm_bridge_enable(struct device *scm_dev); #define QCOM_SCM_SVC_GPU 0x28 #define QCOM_SCM_SVC_GPU_INIT_REGS 0x01 +/* ARM_SMCCC_OWNER_TRUSTED_OS calls */ + +#define QCOM_SCM_SVC_SMCINVOKE 0x06 +#define QCOM_SCM_SMCINVOKE_INVOKE_LEGACY 0x00 +#define QCOM_SCM_SMCINVOKE_CB_RSP 0x01 +#define QCOM_SCM_SMCINVOKE_INVOKE 0x02 + /* common error codes */ #define QCOM_SCM_V2_EBUSY -12 #define QCOM_SCM_ENOMEM -5 diff --git a/drivers/firmware/qcom/qcom_tzmem.c b/drivers/firmware/qcom/qcom_tzmem.c index 12e448669b8b..9f232e53115e 100644 --- a/drivers/firmware/qcom/qcom_tzmem.c +++ b/drivers/firmware/qcom/qcom_tzmem.c @@ -110,7 +110,19 @@ notsupp: return 0; } -static int qcom_tzmem_init_area(struct qcom_tzmem_area *area) +/** + * qcom_tzmem_shm_bridge_create() - Create a SHM bridge. + * @paddr: Physical address of the memory to share. + * @size: Size of the memory to share. + * @handle: Handle to the SHM bridge. + * + * On platforms that support SHM bridge, this function creates a SHM bridge + * for the given memory region with QTEE. The handle returned by this function + * must be passed to qcom_tzmem_shm_bridge_delete() to free the SHM bridge. + * + * Return: On success, returns 0; on failure, returns < 0. + */ +int qcom_tzmem_shm_bridge_create(phys_addr_t paddr, size_t size, u64 *handle) { u64 pfn_and_ns_perm, ipfn_and_s_perm, size_and_flags; int ret; @@ -118,17 +130,49 @@ static int qcom_tzmem_init_area(struct qcom_tzmem_area *area) if (!qcom_tzmem_using_shm_bridge) return 0; - pfn_and_ns_perm = (u64)area->paddr | QCOM_SCM_PERM_RW; - ipfn_and_s_perm = (u64)area->paddr | QCOM_SCM_PERM_RW; - size_and_flags = area->size | (1 << QCOM_SHM_BRIDGE_NUM_VM_SHIFT); + pfn_and_ns_perm = paddr | QCOM_SCM_PERM_RW; + ipfn_and_s_perm = paddr | QCOM_SCM_PERM_RW; + size_and_flags = size | (1 << QCOM_SHM_BRIDGE_NUM_VM_SHIFT); + + ret = qcom_scm_shm_bridge_create(pfn_and_ns_perm, ipfn_and_s_perm, + size_and_flags, QCOM_SCM_VMID_HLOS, + handle); + if (ret) { + dev_err(qcom_tzmem_dev, + "SHM Bridge failed: ret %d paddr 0x%pa, size %zu\n", + ret, &paddr, size); + + return ret; + } + + return 0; +} +EXPORT_SYMBOL_GPL(qcom_tzmem_shm_bridge_create); + +/** + * qcom_tzmem_shm_bridge_delete() - Delete a SHM bridge. + * @handle: Handle to the SHM bridge. + * + * On platforms that support SHM bridge, this function deletes the SHM bridge + * for the given memory region. The handle must be the same as the one + * returned by qcom_tzmem_shm_bridge_create(). + */ +void qcom_tzmem_shm_bridge_delete(u64 handle) +{ + if (qcom_tzmem_using_shm_bridge) + qcom_scm_shm_bridge_delete(handle); +} +EXPORT_SYMBOL_GPL(qcom_tzmem_shm_bridge_delete); + +static int qcom_tzmem_init_area(struct qcom_tzmem_area *area) +{ + int ret; u64 *handle __free(kfree) = kzalloc(sizeof(*handle), GFP_KERNEL); if (!handle) return -ENOMEM; - ret = qcom_scm_shm_bridge_create(pfn_and_ns_perm, ipfn_and_s_perm, - size_and_flags, QCOM_SCM_VMID_HLOS, - handle); + ret = qcom_tzmem_shm_bridge_create(area->paddr, area->size, handle); if (ret) return ret; @@ -141,10 +185,7 @@ static void qcom_tzmem_cleanup_area(struct qcom_tzmem_area *area) { u64 *handle = area->priv; - if (!qcom_tzmem_using_shm_bridge) - return; - - qcom_scm_shm_bridge_delete(*handle); + qcom_tzmem_shm_bridge_delete(*handle); kfree(handle); } diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c index ff2289b52c84..95a577764d5c 100644 --- a/drivers/i2c/busses/i2c-qcom-geni.c +++ b/drivers/i2c/busses/i2c-qcom-geni.c @@ -870,7 +870,13 @@ static int geni_i2c_probe(struct platform_device *pdev) goto err_clk; } proto = geni_se_read_proto(&gi2c->se); - if (proto != GENI_SE_I2C) { + if (proto == GENI_SE_INVALID_PROTO) { + ret = geni_load_se_firmware(&gi2c->se, GENI_SE_I2C); + if (ret) { + dev_err_probe(dev, ret, "i2c firmware load failed ret: %d\n", ret); + goto err_resources; + } + } else if (proto != GENI_SE_I2C) { ret = dev_err_probe(dev, -ENXIO, "Invalid proto %d\n", proto); goto err_resources; } diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c index 3c3b796333a6..cd1779b6a91a 100644 --- a/drivers/soc/qcom/qcom-geni-se.c +++ b/drivers/soc/qcom/qcom-geni-se.c @@ -1,11 +1,16 @@ // SPDX-License-Identifier: GPL-2.0 -// Copyright (c) 2017-2018, The Linux Foundation. All rights reserved. +/* + * Copyright (c) 2017-2018, The Linux Foundation. All rights reserved. + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ /* Disable MMIO tracing to prevent excessive logging of unwanted MMIO traces */ #define __DISABLE_TRACE_MMIO__ #include <linux/acpi.h> +#include <linux/bitfield.h> #include <linux/clk.h> +#include <linux/firmware.h> #include <linux/slab.h> #include <linux/dma-mapping.h> #include <linux/io.h> @@ -110,22 +115,94 @@ struct geni_se_desc { static const char * const icc_path_names[] = {"qup-core", "qup-config", "qup-memory"}; -#define QUP_HW_VER_REG 0x4 +static const char * const protocol_name[] = { "None", "SPI", "UART", "I2C", "I3C", "SPI SLAVE" }; + +/** + * struct se_fw_hdr - Serial Engine firmware configuration header + * + * This structure defines the SE firmware header, which together with the + * firmware payload is stored in individual ELF segments. + * + * @magic: Set to 'SEFW'. + * @version: Structure version number. + * @core_version: QUPV3 hardware version. + * @serial_protocol: Encoded in GENI_FW_REVISION. + * @fw_version: Firmware version, from GENI_FW_REVISION. + * @cfg_version: Configuration version, from GENI_INIT_CFG_REVISION. + * @fw_size_in_items: Number of 32-bit words in GENI_FW_RAM. + * @fw_offset: Byte offset to GENI_FW_RAM array. + * @cfg_size_in_items: Number of GENI_FW_CFG index/value pairs. + * @cfg_idx_offset: Byte offset to GENI_FW_CFG index array. + * @cfg_val_offset: Byte offset to GENI_FW_CFG values array. + */ +struct se_fw_hdr { + __le32 magic; + __le32 version; + __le32 core_version; + __le16 serial_protocol; + __le16 fw_version; + __le16 cfg_version; + __le16 fw_size_in_items; + __le16 fw_offset; + __le16 cfg_size_in_items; + __le16 cfg_idx_offset; + __le16 cfg_val_offset; +}; + +/*Magic numbers*/ +#define SE_MAGIC_NUM 0x57464553 + +#define MAX_GENI_CFG_RAMn_CNT 455 + +#define MI_PBT_NON_PAGED_SEGMENT 0x0 +#define MI_PBT_HASH_SEGMENT 0x2 +#define MI_PBT_NOTUSED_SEGMENT 0x3 +#define MI_PBT_SHARED_SEGMENT 0x4 + +#define MI_PBT_FLAG_PAGE_MODE BIT(20) +#define MI_PBT_FLAG_SEGMENT_TYPE GENMASK(26, 24) +#define MI_PBT_FLAG_ACCESS_TYPE GENMASK(23, 21) + +#define MI_PBT_PAGE_MODE_VALUE(x) FIELD_GET(MI_PBT_FLAG_PAGE_MODE, x) + +#define MI_PBT_SEGMENT_TYPE_VALUE(x) FIELD_GET(MI_PBT_FLAG_SEGMENT_TYPE, x) + +#define MI_PBT_ACCESS_TYPE_VALUE(x) FIELD_GET(MI_PBT_FLAG_ACCESS_TYPE, x) + +#define M_COMMON_GENI_M_IRQ_EN (GENMASK(6, 1) | \ + M_IO_DATA_DEASSERT_EN | \ + M_IO_DATA_ASSERT_EN | M_RX_FIFO_RD_ERR_EN | \ + M_RX_FIFO_WR_ERR_EN | M_TX_FIFO_RD_ERR_EN | \ + M_TX_FIFO_WR_ERR_EN) + +/* Common QUPV3 registers */ +#define QUPV3_HW_VER_REG 0x4 +#define QUPV3_SE_AHB_M_CFG 0x118 +#define QUPV3_COMMON_CFG 0x120 +#define QUPV3_COMMON_CGC_CTRL 0x21c + +/* QUPV3_COMMON_CFG fields */ +#define FAST_SWITCH_TO_HIGH_DISABLE BIT(0) + +/* QUPV3_SE_AHB_M_CFG fields */ +#define AHB_M_CLK_CGC_ON BIT(0) + +/* QUPV3_COMMON_CGC_CTRL fields */ +#define COMMON_CSR_SLV_CLK_CGC_ON BIT(0) /* Common SE registers */ -#define GENI_INIT_CFG_REVISION 0x0 -#define GENI_S_INIT_CFG_REVISION 0x4 -#define GENI_OUTPUT_CTRL 0x24 -#define GENI_CGC_CTRL 0x28 -#define GENI_CLK_CTRL_RO 0x60 -#define GENI_FW_S_REVISION_RO 0x6c +#define SE_GENI_INIT_CFG_REVISION 0x0 +#define SE_GENI_S_INIT_CFG_REVISION 0x4 +#define SE_GENI_CGC_CTRL 0x28 +#define SE_GENI_CLK_CTRL_RO 0x60 +#define SE_GENI_FW_S_REVISION_RO 0x6c +#define SE_GENI_CFG_REG0 0x100 #define SE_GENI_BYTE_GRAN 0x254 #define SE_GENI_TX_PACKING_CFG0 0x260 #define SE_GENI_TX_PACKING_CFG1 0x264 #define SE_GENI_RX_PACKING_CFG0 0x284 #define SE_GENI_RX_PACKING_CFG1 0x288 -#define SE_GENI_M_GP_LENGTH 0x910 -#define SE_GENI_S_GP_LENGTH 0x914 +#define SE_GENI_S_IRQ_ENABLE 0x644 #define SE_DMA_TX_PTR_L 0xc30 #define SE_DMA_TX_PTR_H 0xc34 #define SE_DMA_TX_ATTR 0xc38 @@ -142,12 +219,20 @@ static const char * const icc_path_names[] = {"qup-core", "qup-config", #define SE_DMA_RX_IRQ_EN 0xd48 #define SE_DMA_RX_IRQ_EN_SET 0xd4c #define SE_DMA_RX_IRQ_EN_CLR 0xd50 -#define SE_DMA_RX_LEN_IN 0xd54 #define SE_DMA_RX_MAX_BURST 0xd5c #define SE_DMA_RX_FLUSH 0xd60 #define SE_GSI_EVENT_EN 0xe18 #define SE_IRQ_EN 0xe1c #define SE_DMA_GENERAL_CFG 0xe30 +#define SE_GENI_FW_REVISION 0x1000 +#define SE_GENI_S_FW_REVISION 0x1004 +#define SE_GENI_CFG_RAMN 0x1010 +#define SE_GENI_CLK_CTRL 0x2000 +#define SE_DMA_IF_EN 0x2004 +#define SE_FIFO_IF_DISABLE 0x2008 + +/* GENI_FW_REVISION_RO fields */ +#define FW_REV_VERSION_MSK GENMASK(7, 0) /* GENI_OUTPUT_CTRL fields */ #define DEFAULT_IO_OUTPUT_CTRL_MSK GENMASK(6, 0) @@ -179,13 +264,22 @@ static const char * const icc_path_names[] = {"qup-core", "qup-config", /* SE_DMA_GENERAL_CFG */ #define DMA_RX_CLK_CGC_ON BIT(0) #define DMA_TX_CLK_CGC_ON BIT(1) -#define DMA_AHB_SLV_CFG_ON BIT(2) +#define DMA_AHB_SLV_CLK_CGC_ON BIT(2) #define AHB_SEC_SLV_CLK_CGC_ON BIT(3) #define DUMMY_RX_NON_BUFFERABLE BIT(4) #define RX_DMA_ZERO_PADDING_EN BIT(5) #define RX_DMA_IRQ_DELAY_MSK GENMASK(8, 6) #define RX_DMA_IRQ_DELAY_SHFT 6 +/* GENI_CLK_CTRL fields */ +#define SER_CLK_SEL BIT(0) + +/* GENI_DMA_IF_EN fields */ +#define DMA_IF_EN BIT(0) + +#define geni_setbits32(_addr, _v) writel(readl(_addr) | (_v), _addr) +#define geni_clrbits32(_addr, _v) writel(readl(_addr) & ~(_v), _addr) + /** * geni_se_get_qup_hw_version() - Read the QUP wrapper Hardware version * @se: Pointer to the corresponding serial engine. @@ -196,7 +290,7 @@ u32 geni_se_get_qup_hw_version(struct geni_se *se) { struct geni_wrapper *wrapper = se->wrapper; - return readl_relaxed(wrapper->base + QUP_HW_VER_REG); + return readl_relaxed(wrapper->base + QUPV3_HW_VER_REG); } EXPORT_SYMBOL_GPL(geni_se_get_qup_hw_version); @@ -220,12 +314,12 @@ static void geni_se_io_init(void __iomem *base) { u32 val; - val = readl_relaxed(base + GENI_CGC_CTRL); + val = readl_relaxed(base + SE_GENI_CGC_CTRL); val |= DEFAULT_CGC_EN; - writel_relaxed(val, base + GENI_CGC_CTRL); + writel_relaxed(val, base + SE_GENI_CGC_CTRL); val = readl_relaxed(base + SE_DMA_GENERAL_CFG); - val |= AHB_SEC_SLV_CLK_CGC_ON | DMA_AHB_SLV_CFG_ON; + val |= AHB_SEC_SLV_CLK_CGC_ON | DMA_AHB_SLV_CLK_CGC_ON; val |= DMA_TX_CLK_CGC_ON | DMA_RX_CLK_CGC_ON; writel_relaxed(val, base + SE_DMA_GENERAL_CFG); @@ -658,9 +752,12 @@ int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq, } EXPORT_SYMBOL_GPL(geni_se_clk_freq_match); -#define GENI_SE_DMA_DONE_EN BIT(0) -#define GENI_SE_DMA_EOT_EN BIT(1) -#define GENI_SE_DMA_AHB_ERR_EN BIT(2) +#define GENI_SE_DMA_DONE_EN BIT(0) +#define GENI_SE_DMA_EOT_EN BIT(1) +#define GENI_SE_DMA_AHB_ERR_EN BIT(2) +#define GENI_SE_DMA_RESET_DONE_EN BIT(3) +#define GENI_SE_DMA_FLUSH_DONE BIT(4) + #define GENI_SE_DMA_EOT_BUF BIT(0) /** @@ -891,6 +988,377 @@ int geni_icc_disable(struct geni_se *se) } EXPORT_SYMBOL_GPL(geni_icc_disable); +/** + * geni_find_protocol_fw() - Locate and validate SE firmware for a protocol. + * @dev: Pointer to the device structure. + * @fw: Pointer to the firmware image. + * @protocol: Expected serial engine protocol type. + * + * Identifies the appropriate firmware image or configuration required for a + * specific communication protocol instance running on a Qualcomm GENI + * controller. + * + * Return: pointer to a valid 'struct se_fw_hdr' if found, or NULL otherwise. + */ +static struct se_fw_hdr *geni_find_protocol_fw(struct device *dev, const struct firmware *fw, + enum geni_se_protocol_type protocol) +{ + const struct elf32_hdr *ehdr; + const struct elf32_phdr *phdrs; + const struct elf32_phdr *phdr; + struct se_fw_hdr *sefw; + u32 fw_end, cfg_idx_end, cfg_val_end; + u16 fw_size; + int i; + + if (!fw || fw->size < sizeof(struct elf32_hdr)) + return NULL; + + ehdr = (const struct elf32_hdr *)fw->data; + phdrs = (const struct elf32_phdr *)(fw->data + ehdr->e_phoff); + + /* + * The firmware is expected to have at least two program headers (segments). + * One for metadata and the other for the actual protocol-specific firmware. + */ + if (ehdr->e_phnum < 2) { + dev_err(dev, "Invalid firmware: less than 2 program headers\n"); + return NULL; + } + + for (i = 0; i < ehdr->e_phnum; i++) { + phdr = &phdrs[i]; + + if (fw->size < phdr->p_offset + phdr->p_filesz) { + dev_err(dev, "Firmware size (%zu) < expected offset (%u) + size (%u)\n", + fw->size, phdr->p_offset, phdr->p_filesz); + return NULL; + } + + if (phdr->p_type != PT_LOAD || !phdr->p_memsz) + continue; + + if (MI_PBT_PAGE_MODE_VALUE(phdr->p_flags) != MI_PBT_NON_PAGED_SEGMENT || + MI_PBT_SEGMENT_TYPE_VALUE(phdr->p_flags) == MI_PBT_HASH_SEGMENT || + MI_PBT_ACCESS_TYPE_VALUE(phdr->p_flags) == MI_PBT_NOTUSED_SEGMENT || + MI_PBT_ACCESS_TYPE_VALUE(phdr->p_flags) == MI_PBT_SHARED_SEGMENT) + continue; + + if (phdr->p_filesz < sizeof(struct se_fw_hdr)) + continue; + + sefw = (struct se_fw_hdr *)(fw->data + phdr->p_offset); + fw_size = le16_to_cpu(sefw->fw_size_in_items); + fw_end = le16_to_cpu(sefw->fw_offset) + fw_size * sizeof(u32); + cfg_idx_end = le16_to_cpu(sefw->cfg_idx_offset) + + le16_to_cpu(sefw->cfg_size_in_items) * sizeof(u8); + cfg_val_end = le16_to_cpu(sefw->cfg_val_offset) + + le16_to_cpu(sefw->cfg_size_in_items) * sizeof(u32); + + if (le32_to_cpu(sefw->magic) != SE_MAGIC_NUM || le32_to_cpu(sefw->version) != 1) + continue; + + if (le32_to_cpu(sefw->serial_protocol) != protocol) + continue; + + if (fw_size % 2 != 0) { + fw_size++; + sefw->fw_size_in_items = cpu_to_le16(fw_size); + } + + if (fw_size >= MAX_GENI_CFG_RAMn_CNT) { + dev_err(dev, + "Firmware size (%u) exceeds max allowed RAMn count (%u)\n", + fw_size, MAX_GENI_CFG_RAMn_CNT); + continue; + } + + if (fw_end > phdr->p_filesz || cfg_idx_end > phdr->p_filesz || + cfg_val_end > phdr->p_filesz) { + dev_err(dev, "Truncated or corrupt SE FW segment found at index %d\n", i); + continue; + } + + return sefw; + } + + dev_err(dev, "Failed to get %s protocol firmware\n", protocol_name[protocol]); + return NULL; +} + +/** + * geni_configure_xfer_mode() - Set the transfer mode. + * @se: Pointer to the concerned serial engine. + * @mode: SE data transfer mode. + * + * Set the transfer mode to either FIFO or DMA according to the mode specified + * by the protocol driver. + * + * Return: 0 if successful, otherwise return an error value. + */ +static int geni_configure_xfer_mode(struct geni_se *se, enum geni_se_xfer_mode mode) +{ + /* Configure SE FIFO, DMA or GSI mode. */ + switch (mode) { + case GENI_GPI_DMA: + geni_setbits32(se->base + SE_GENI_DMA_MODE_EN, GENI_DMA_MODE_EN); + writel(0x0, se->base + SE_IRQ_EN); + writel(DMA_RX_EVENT_EN | DMA_TX_EVENT_EN | GENI_M_EVENT_EN | GENI_S_EVENT_EN, + se->base + SE_GSI_EVENT_EN); + break; + + case GENI_SE_FIFO: + geni_clrbits32(se->base + SE_GENI_DMA_MODE_EN, GENI_DMA_MODE_EN); + writel(DMA_RX_IRQ_EN | DMA_TX_IRQ_EN | GENI_M_IRQ_EN | GENI_S_IRQ_EN, + se->base + SE_IRQ_EN); + writel(0x0, se->base + SE_GSI_EVENT_EN); + break; + + case GENI_SE_DMA: + geni_setbits32(se->base + SE_GENI_DMA_MODE_EN, GENI_DMA_MODE_EN); + writel(DMA_RX_IRQ_EN | DMA_TX_IRQ_EN | GENI_M_IRQ_EN | GENI_S_IRQ_EN, + se->base + SE_IRQ_EN); + writel(0x0, se->base + SE_GSI_EVENT_EN); + break; + + default: + dev_err(se->dev, "Invalid geni-se transfer mode: %d\n", mode); + return -EINVAL; + } + return 0; +} + +/** + * geni_enable_interrupts() - Enable interrupts. + * @se: Pointer to the concerned serial engine. + * + * Enable the required interrupts during the firmware load process. + */ +static void geni_enable_interrupts(struct geni_se *se) +{ + u32 val; + + /* Enable required interrupts. */ + writel(M_COMMON_GENI_M_IRQ_EN, se->base + SE_GENI_M_IRQ_EN); + + val = S_CMD_OVERRUN_EN | S_ILLEGAL_CMD_EN | S_CMD_CANCEL_EN | S_CMD_ABORT_EN | + S_GP_IRQ_0_EN | S_GP_IRQ_1_EN | S_GP_IRQ_2_EN | S_GP_IRQ_3_EN | + S_RX_FIFO_WR_ERR_EN | S_RX_FIFO_RD_ERR_EN; + writel(val, se->base + SE_GENI_S_IRQ_ENABLE); + + /* DMA mode configuration. */ + val = GENI_SE_DMA_RESET_DONE_EN | GENI_SE_DMA_AHB_ERR_EN | GENI_SE_DMA_DONE_EN; + writel(val, se->base + SE_DMA_TX_IRQ_EN_SET); + val = GENI_SE_DMA_FLUSH_DONE | GENI_SE_DMA_RESET_DONE_EN | GENI_SE_DMA_AHB_ERR_EN | + GENI_SE_DMA_DONE_EN; + writel(val, se->base + SE_DMA_RX_IRQ_EN_SET); +} + +/** + * geni_write_fw_revision() - Write the firmware revision. + * @se: Pointer to the concerned serial engine. + * @serial_protocol: serial protocol type. + * @fw_version: QUP firmware version. + * + * Write the firmware revision and protocol into the respective register. + */ +static void geni_write_fw_revision(struct geni_se *se, u16 serial_protocol, u16 fw_version) +{ + u32 reg; + + reg = FIELD_PREP(FW_REV_PROTOCOL_MSK, serial_protocol); + reg |= FIELD_PREP(FW_REV_VERSION_MSK, fw_version); + + writel(reg, se->base + SE_GENI_FW_REVISION); + writel(reg, se->base + SE_GENI_S_FW_REVISION); +} + +/** + * geni_load_se_fw() - Load Serial Engine specific firmware. + * @se: Pointer to the concerned serial engine. + * @fw: Pointer to the firmware structure. + * @mode: SE data transfer mode. + * @protocol: Protocol type to be used with the SE (e.g., UART, SPI, I2C). + * + * Load the protocol firmware into the IRAM of the Serial Engine. + * + * Return: 0 if successful, otherwise return an error value. + */ +static int geni_load_se_fw(struct geni_se *se, const struct firmware *fw, + enum geni_se_xfer_mode mode, enum geni_se_protocol_type protocol) +{ + const u32 *fw_data, *cfg_val_arr; + const u8 *cfg_idx_arr; + u32 i, reg_value; + int ret; + struct se_fw_hdr *hdr; + + hdr = geni_find_protocol_fw(se->dev, fw, protocol); + if (!hdr) + return -EINVAL; + + fw_data = (const u32 *)((u8 *)hdr + le16_to_cpu(hdr->fw_offset)); + cfg_idx_arr = (const u8 *)hdr + le16_to_cpu(hdr->cfg_idx_offset); + cfg_val_arr = (const u32 *)((u8 *)hdr + le16_to_cpu(hdr->cfg_val_offset)); + + ret = geni_icc_set_bw(se); + if (ret) + return ret; + + ret = geni_icc_enable(se); + if (ret) + return ret; + + ret = geni_se_resources_on(se); + if (ret) + goto out_icc_disable; + + /* + * Disable high-priority interrupts until all currently executing + * low-priority interrupts have been fully handled. + */ + geni_setbits32(se->wrapper->base + QUPV3_COMMON_CFG, FAST_SWITCH_TO_HIGH_DISABLE); + + /* Set AHB_M_CLK_CGC_ON to indicate hardware controls se-wrapper cgc clock. */ + geni_setbits32(se->wrapper->base + QUPV3_SE_AHB_M_CFG, AHB_M_CLK_CGC_ON); + + /* Let hardware to control common cgc. */ + geni_setbits32(se->wrapper->base + QUPV3_COMMON_CGC_CTRL, COMMON_CSR_SLV_CLK_CGC_ON); + + /* + * Setting individual bits in GENI_OUTPUT_CTRL activates corresponding output lines, + * allowing the hardware to drive data as configured. + */ + writel(0x0, se->base + GENI_OUTPUT_CTRL); + + /* Set SCLK and HCLK to program RAM */ + geni_setbits32(se->base + SE_GENI_CGC_CTRL, PROG_RAM_SCLK_OFF | PROG_RAM_HCLK_OFF); + writel(0x0, se->base + SE_GENI_CLK_CTRL); + geni_clrbits32(se->base + SE_GENI_CGC_CTRL, PROG_RAM_SCLK_OFF | PROG_RAM_HCLK_OFF); + + /* Enable required clocks for DMA CSR, TX and RX. */ + reg_value = AHB_SEC_SLV_CLK_CGC_ON | DMA_AHB_SLV_CLK_CGC_ON | + DMA_TX_CLK_CGC_ON | DMA_RX_CLK_CGC_ON; + geni_setbits32(se->base + SE_DMA_GENERAL_CFG, reg_value); + + /* Let hardware control CGC by default. */ + writel(DEFAULT_CGC_EN, se->base + SE_GENI_CGC_CTRL); + + /* Set version of the configuration register part of firmware. */ + writel(le16_to_cpu(hdr->cfg_version), se->base + SE_GENI_INIT_CFG_REVISION); + writel(le16_to_cpu(hdr->cfg_version), se->base + SE_GENI_S_INIT_CFG_REVISION); + + /* Configure GENI primitive table. */ + for (i = 0; i < le16_to_cpu(hdr->cfg_size_in_items); i++) + writel(cfg_val_arr[i], + se->base + SE_GENI_CFG_REG0 + (cfg_idx_arr[i] * sizeof(u32))); + + /* Configure condition for assertion of RX_RFR_WATERMARK condition. */ + reg_value = geni_se_get_rx_fifo_depth(se); + writel(reg_value - 2, se->base + SE_GENI_RX_RFR_WATERMARK_REG); + + /* Let hardware control CGC */ + geni_setbits32(se->base + GENI_OUTPUT_CTRL, DEFAULT_IO_OUTPUT_CTRL_MSK); + + ret = geni_configure_xfer_mode(se, mode); + if (ret) + goto out_resources_off; + + geni_enable_interrupts(se); + + geni_write_fw_revision(se, le16_to_cpu(hdr->serial_protocol), le16_to_cpu(hdr->fw_version)); + + /* Program RAM address space. */ + memcpy_toio(se->base + SE_GENI_CFG_RAMN, fw_data, + le16_to_cpu(hdr->fw_size_in_items) * sizeof(u32)); + + /* Put default values on GENI's output pads. */ + writel_relaxed(0x1, se->base + GENI_FORCE_DEFAULT_REG); + + /* Toggle SCLK/HCLK from high to low to finalize RAM programming and apply config. */ + geni_setbits32(se->base + SE_GENI_CGC_CTRL, PROG_RAM_SCLK_OFF | PROG_RAM_HCLK_OFF); + geni_setbits32(se->base + SE_GENI_CLK_CTRL, SER_CLK_SEL); + geni_clrbits32(se->base + SE_GENI_CGC_CTRL, PROG_RAM_SCLK_OFF | PROG_RAM_HCLK_OFF); + + /* Serial engine DMA interface is enabled. */ + geni_setbits32(se->base + SE_DMA_IF_EN, DMA_IF_EN); + + /* Enable or disable FIFO interface of the serial engine. */ + if (mode == GENI_SE_FIFO) + geni_clrbits32(se->base + SE_FIFO_IF_DISABLE, FIFO_IF_DISABLE); + else + geni_setbits32(se->base + SE_FIFO_IF_DISABLE, FIFO_IF_DISABLE); + +out_resources_off: + geni_se_resources_off(se); + +out_icc_disable: + geni_icc_disable(se); + return ret; +} + +/** + * geni_load_se_firmware() - Load firmware for SE based on protocol + * @se: Pointer to the concerned serial engine. + * @protocol: Protocol type to be used with the SE (e.g., UART, SPI, I2C). + * + * Retrieves the firmware name from device properties and sets the transfer mode + * (FIFO or GSI DMA) based on device tree configuration. Enforces FIFO mode for + * UART protocol due to lack of GSI DMA support. Requests the firmware and loads + * it into the SE. + * + * Return: 0 on success, negative error code on failure. + */ +int geni_load_se_firmware(struct geni_se *se, enum geni_se_protocol_type protocol) +{ + const char *fw_name; + const struct firmware *fw; + enum geni_se_xfer_mode mode = GENI_SE_FIFO; + int ret; + + if (protocol >= ARRAY_SIZE(protocol_name)) { + dev_err(se->dev, "Invalid geni-se protocol: %d", protocol); + return -EINVAL; + } + + ret = device_property_read_string(se->wrapper->dev, "firmware-name", &fw_name); + if (ret) { + dev_err(se->dev, "Failed to read firmware-name property: %d\n", ret); + return -EINVAL; + } + + if (of_property_read_bool(se->dev->of_node, "qcom,enable-gsi-dma")) + mode = GENI_GPI_DMA; + + /* GSI mode is not supported by the UART driver; therefore, setting FIFO mode */ + if (protocol == GENI_SE_UART) + mode = GENI_SE_FIFO; + + ret = request_firmware(&fw, fw_name, se->dev); + if (ret) { + if (ret == -ENOENT) + return -EPROBE_DEFER; + + dev_err(se->dev, "Failed to request firmware '%s' for protocol %d: ret: %d\n", + fw_name, protocol, ret); + return ret; + } + + ret = geni_load_se_fw(se, fw, mode, protocol); + release_firmware(fw); + + if (ret) { + dev_err(se->dev, "Failed to load SE firmware for protocol %d: ret: %d\n", + protocol, ret); + return ret; + } + + dev_dbg(se->dev, "Firmware load for %s protocol is successful for xfer mode: %d\n", + protocol_name[protocol], mode); + return 0; +} +EXPORT_SYMBOL_GPL(geni_load_se_firmware); + static int geni_se_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c index 768d7482102a..a0d8d3425c6c 100644 --- a/drivers/spi/spi-geni-qcom.c +++ b/drivers/spi/spi-geni-qcom.c @@ -671,6 +671,12 @@ static int spi_geni_init(struct spi_geni_master *mas) goto out_pm; } spi_slv_setup(mas); + } else if (proto == GENI_SE_INVALID_PROTO) { + ret = geni_load_se_firmware(se, GENI_SE_SPI); + if (ret) { + dev_err(mas->dev, "spi master firmware load failed ret: %d\n", ret); + goto out_pm; + } } else if (proto != GENI_SE_SPI) { dev_err(mas->dev, "Invalid proto %d\n", proto); goto out_pm; diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c index 32ec632fd080..3f5b87c4cc54 100644 --- a/drivers/tty/serial/qcom_geni_serial.c +++ b/drivers/tty/serial/qcom_geni_serial.c @@ -1200,7 +1200,13 @@ static int qcom_geni_serial_port_setup(struct uart_port *uport) int ret; proto = geni_se_read_proto(&port->se); - if (proto != GENI_SE_UART) { + if (proto == GENI_SE_INVALID_PROTO) { + ret = geni_load_se_firmware(&port->se, GENI_SE_UART); + if (ret) { + dev_err(uport->dev, "UART firmware load failed ret: %d\n", ret); + return ret; + } + } else if (proto != GENI_SE_UART) { dev_err(uport->dev, "Invalid FW loaded, proto: %d\n", proto); return -ENXIO; } diff --git a/include/linux/firmware/qcom/qcom_scm.h b/include/linux/firmware/qcom/qcom_scm.h index 0f667bf1d4d9..a55ca771286b 100644 --- a/include/linux/firmware/qcom/qcom_scm.h +++ b/include/linux/firmware/qcom/qcom_scm.h @@ -175,4 +175,10 @@ static inline int qcom_scm_qseecom_app_send(u32 app_id, #endif /* CONFIG_QCOM_QSEECOM */ +int qcom_scm_qtee_invoke_smc(phys_addr_t inbuf, size_t inbuf_size, + phys_addr_t outbuf, size_t outbuf_size, + u64 *result, u64 *response_type); +int qcom_scm_qtee_callback_response(phys_addr_t buf, size_t buf_size, + u64 *result, u64 *response_type); + #endif diff --git a/include/linux/firmware/qcom/qcom_tzmem.h b/include/linux/firmware/qcom/qcom_tzmem.h index b83b63a0c049..48ac0e5454c7 100644 --- a/include/linux/firmware/qcom/qcom_tzmem.h +++ b/include/linux/firmware/qcom/qcom_tzmem.h @@ -53,4 +53,19 @@ DEFINE_FREE(qcom_tzmem, void *, if (_T) qcom_tzmem_free(_T)) phys_addr_t qcom_tzmem_to_phys(void *ptr); +#if IS_ENABLED(CONFIG_QCOM_TZMEM_MODE_SHMBRIDGE) +int qcom_tzmem_shm_bridge_create(phys_addr_t paddr, size_t size, u64 *handle); +void qcom_tzmem_shm_bridge_delete(u64 handle); +#else +static inline int qcom_tzmem_shm_bridge_create(phys_addr_t paddr, + size_t size, u64 *handle) +{ + return 0; +} + +static inline void qcom_tzmem_shm_bridge_delete(u64 handle) +{ +} +#endif + #endif /* __QCOM_TZMEM */ diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h index 2996a3c28ef3..0a984e2579fe 100644 --- a/include/linux/soc/qcom/geni-se.h +++ b/include/linux/soc/qcom/geni-se.h @@ -1,6 +1,7 @@ /* SPDX-License-Identifier: GPL-2.0 */ /* * Copyright (c) 2017-2018, The Linux Foundation. All rights reserved. + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. */ #ifndef _LINUX_QCOM_GENI_SE @@ -36,6 +37,7 @@ enum geni_se_protocol_type { GENI_SE_I2C, GENI_SE_I3C, GENI_SE_SPI_SLAVE, + GENI_SE_INVALID_PROTO = 255, }; struct geni_wrapper; @@ -531,5 +533,7 @@ void geni_icc_set_tag(struct geni_se *se, u32 tag); int geni_icc_enable(struct geni_se *se); int geni_icc_disable(struct geni_se *se); + +int geni_load_se_firmware(struct geni_se *se, enum geni_se_protocol_type protocol); #endif #endif |