diff options
| -rw-r--r-- | Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt | 27 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt | 41 |
2 files changed, 43 insertions, 25 deletions
diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index 34c952883276..df0933043a5b 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt @@ -6,27 +6,10 @@ Practice : Universal Serial Bus" with the following modifications and additions : Required properties : - - compatible : Should be "nvidia,tegra20-ehci" for USB controllers - used in host mode. - - phy_type : Should be one of "ulpi" or "utmi". - - nvidia,vbus-gpio : If present, specifies a gpio that needs to be - activated for the bus to be powered. - - nvidia,phy : phandle of the PHY instance, the controller is connected to. - -Required properties for phy_type == ulpi: - - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. + - compatible : Should be "nvidia,tegra20-ehci". + - nvidia,phy : phandle of the PHY that the controller is connected to. + - clocks : Contains a single entry which defines the USB controller's clock. Optional properties: - - dr_mode : dual role mode. Indicates the working mode for - nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral", - or "otg". Default to "host" if not defined for backward compatibility. - host means this is a host controller - peripheral means it is device controller - otg means it can operate as either ("on the go") - - nvidia,has-legacy-mode : boolean indicates whether this controller can - operate in legacy mode (as APX 2500 / 2600). In legacy mode some - registers are accessed through the APB_MISC base address instead of - the USB controller. Since this is a legacy issue it probably does not - warrant a compatible string of its own. - - nvidia,needs-double-reset : boolean is to be set for some of the Tegra2 - USB ports, which need reset twice due to hardware issues. + - nvidia,needs-double-reset : boolean is to be set for some of the Tegra20 + USB ports, which need reset twice due to hardware issues. diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index 6bdaba2f0aa1..c4c9e9e664aa 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -4,14 +4,49 @@ The device node for Tegra SOC USB PHY: Required properties : - compatible : Should be "nvidia,tegra20-usb-phy". - - reg : Address and length of the register set for the USB PHY interface. - - phy_type : Should be one of "ulpi" or "utmi". + - reg : Defines the following set of registers, in the order listed: + - The PHY's own register set. + Always present. + - The register set of the PHY containing the UTMI pad control registers. + Present if-and-only-if phy_type == utmi. + - phy_type : Should be one of "utmi", "ulpi" or "hsic". + - clocks : Defines the clocks listed in the clock-names property. + - clock-names : The following clock names must be present: + - reg: The clock needed to access the PHY's own registers. This is the + associated EHCI controller's clock. Always present. + - pll_u: PLL_U. Always present. + - timer: The timeout clock (clk_m). Present if phy_type == utmi. + - utmi-pads: The clock needed to access the UTMI pad control registers. + Present if phy_type == utmi. + - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). + Present if phy_type == ulpi, and ULPI link mode is in use. Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. +Required PHY timing params for utmi phy: + - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before + start of sync launches RxActive + - nvidia,elastic-limit : Variable FIFO Depth of elastic input store + - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait + before declare IDLE. + - nvidia,term-range-adj : Range adjusment on terminations + - nvidia,xcvr-setup : HS driver output control + - nvidia,xcvr-lsfslew : LS falling slew rate control. + - nvidia,xcvr-lsrslew : LS rising slew rate control. + Optional properties: - nvidia,has-legacy-mode : boolean indicates whether this controller can operate in legacy mode (as APX 2500 / 2600). In legacy mode some registers are accessed through the APB_MISC base address instead of - the USB controller.
\ No newline at end of file + the USB controller. + - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power + optimizations for the devices that are always connected. e.g. modem. + - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be + "host", "peripheral", or "otg". Defaults to "host" if not defined. + host means this is a host controller + peripheral means it is device controller + otg means it can operate as either ("on the go") + +Required properties for dr_mode == otg: + - vbus-supply: regulator for VBUS |