diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml | 5 | ||||
| -rw-r--r-- | Documentation/networking/napi.rst | 5 | ||||
| -rw-r--r-- | Documentation/sound/alsa-configuration.rst | 29 |
3 files changed, 32 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml index a65a42ccaafe..a82360bed188 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.yaml @@ -20,6 +20,7 @@ properties: - enum: - fsl,imx7ulp-spi - fsl,imx8qxp-spi + - nxp,s32g2-lpspi - items: - enum: - fsl,imx8ulp-spi @@ -27,6 +28,10 @@ properties: - fsl,imx94-spi - fsl,imx95-spi - const: fsl,imx7ulp-spi + - items: + - const: nxp,s32g3-lpspi + - const: nxp,s32g2-lpspi + reg: maxItems: 1 diff --git a/Documentation/networking/napi.rst b/Documentation/networking/napi.rst index a15754adb041..7dd60366f4ff 100644 --- a/Documentation/networking/napi.rst +++ b/Documentation/networking/napi.rst @@ -433,9 +433,8 @@ Threaded NAPI Threaded NAPI is an operating mode that uses dedicated kernel threads rather than software IRQ context for NAPI processing. -The configuration is per netdevice and will affect all -NAPI instances of that device. Each NAPI instance will spawn a separate -thread (called ``napi/${ifc-name}-${napi-id}``). +Each threaded NAPI instance will spawn a separate thread +(called ``napi/${ifc-name}-${napi-id}``). It is recommended to pin each kernel thread to a single CPU, the same CPU as the CPU which services the interrupt. Note that the mapping diff --git a/Documentation/sound/alsa-configuration.rst b/Documentation/sound/alsa-configuration.rst index a45174d165eb..062b86522e4d 100644 --- a/Documentation/sound/alsa-configuration.rst +++ b/Documentation/sound/alsa-configuration.rst @@ -2253,8 +2253,15 @@ device_setup Default: 0x0000 ignore_ctl_error Ignore any USB-controller regarding mixer interface (default: no) + ``ignore_ctl_error=1`` may help when you get an error at accessing + the mixer element such as URB error -22. This happens on some + buggy USB device or the controller. This workaround corresponds to + the ``quirk_flags`` bit 14, too. autoclock Enable auto-clock selection for UAC2 devices (default: yes) +lowlatency + Enable low latency playback mode (default: yes). + Could disable it to switch back to the old mode if face a regression. quirk_alias Quirk alias list, pass strings like ``0123abcd:5678beef``, which applies the existing quirk for the device 5678:beef to a new @@ -2284,6 +2291,11 @@ delayed_register The driver prints a message like "Found post-registration device assignment: 1234abcd:04" for such a device, so that user can notice the need. +skip_validation + Skip unit descriptor validation (default: no). + The option is used to ignores the validation errors with the hexdump + of the unit descriptor instead of a driver probe error, so that we + can check its details. quirk_flags Contains the bit flags for various device specific workarounds. Applied to the corresponding card index. @@ -2307,6 +2319,16 @@ quirk_flags * bit 16: Set up the interface at first like UAC1 * bit 17: Apply the generic implicit feedback sync mode * bit 18: Don't apply implicit feedback sync mode + * bit 19: Don't closed interface during setting sample rate + * bit 20: Force an interface reset whenever stopping & restarting + a stream + * bit 21: Do not set PCM rate (frequency) when only one rate is + available for the given endpoint. + * bit 22: Set the fixed resolution 16 for Mic Capture Volume + * bit 23: Set the fixed resolution 384 for Mic Capture Volume + * bit 24: Set minimum volume control value as mute for devices + where the lowest playback value represents muted state instead + of minimum audible volume This module supports multiple devices, autoprobe and hotplugging. @@ -2314,10 +2336,9 @@ NB: ``nrpacks`` parameter can be modified dynamically via sysfs. Don't put the value over 20. Changing via sysfs has no sanity check. -NB: ``ignore_ctl_error=1`` may help when you get an error at accessing -the mixer element such as URB error -22. This happens on some -buggy USB device or the controller. This workaround corresponds to -the ``quirk_flags`` bit 14, too. +NB: ``ignore_ctl_error=1`` just provides a quick way to work around the +issues. If you have a buggy device that requires these quirks, please +report it to the upstream. NB: ``quirk_alias`` option is provided only for testing / development. If you want to have a proper support, contact to upstream for |