diff options
Diffstat (limited to 'arch/x86/platform')
| -rw-r--r-- | arch/x86/platform/ce4100/ce4100.c | 95 | ||||
| -rw-r--r-- | arch/x86/platform/efi/efi_64.c | 4 |
2 files changed, 2 insertions, 97 deletions
diff --git a/arch/x86/platform/ce4100/ce4100.c b/arch/x86/platform/ce4100/ce4100.c index f8126821a94d..aaa7017416f7 100644 --- a/arch/x86/platform/ce4100/ce4100.c +++ b/arch/x86/platform/ce4100/ce4100.c @@ -5,19 +5,12 @@ * (C) Copyright 2010 Intel Corporation */ #include <linux/init.h> -#include <linux/kernel.h> -#include <linux/irq.h> #include <linux/reboot.h> -#include <linux/serial_reg.h> -#include <linux/serial_8250.h> #include <asm/ce4100.h> #include <asm/prom.h> #include <asm/setup.h> -#include <asm/i8259.h> #include <asm/io.h> -#include <asm/io_apic.h> -#include <asm/emergency-restart.h> /* * The CE4100 platform has an internal 8051 Microcontroller which is @@ -31,94 +24,6 @@ static void ce4100_power_off(void) outb(0x4, 0xcf9); } -#ifdef CONFIG_SERIAL_8250 - -static unsigned int mem_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return readl(p->membase + offset); -} - -/* - * The UART Tx interrupts are not set under some conditions and therefore serial - * transmission hangs. This is a silicon issue and has not been root caused. The - * workaround for this silicon issue checks UART_LSR_THRE bit and UART_LSR_TEMT - * bit of LSR register in interrupt handler to see whether at least one of these - * two bits is set, if so then process the transmit request. If this workaround - * is not applied, then the serial transmission may hang. This workaround is for - * errata number 9 in Errata - B step. -*/ - -static unsigned int ce4100_mem_serial_in(struct uart_port *p, int offset) -{ - unsigned int ret, ier, lsr; - - if (offset == UART_IIR) { - offset = offset << p->regshift; - ret = readl(p->membase + offset); - if (ret & UART_IIR_NO_INT) { - /* see if the TX interrupt should have really set */ - ier = mem_serial_in(p, UART_IER); - /* see if the UART's XMIT interrupt is enabled */ - if (ier & UART_IER_THRI) { - lsr = mem_serial_in(p, UART_LSR); - /* now check to see if the UART should be - generating an interrupt (but isn't) */ - if (lsr & (UART_LSR_THRE | UART_LSR_TEMT)) - ret &= ~UART_IIR_NO_INT; - } - } - } else - ret = mem_serial_in(p, offset); - return ret; -} - -static void ce4100_mem_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - writel(value, p->membase + offset); -} - -static void ce4100_serial_fixup(int port, struct uart_port *up, - u32 *capabilities) -{ -#ifdef CONFIG_EARLY_PRINTK - /* - * Over ride the legacy port configuration that comes from - * asm/serial.h. Using the ioport driver then switching to the - * PCI memmaped driver hangs the IOAPIC - */ - if (up->iotype != UPIO_MEM32) { - up->uartclk = 14745600; - up->mapbase = 0xdffe0200; - set_fixmap_nocache(FIX_EARLYCON_MEM_BASE, - up->mapbase & PAGE_MASK); - up->membase = - (void __iomem *)__fix_to_virt(FIX_EARLYCON_MEM_BASE); - up->membase += up->mapbase & ~PAGE_MASK; - up->mapbase += port * 0x100; - up->membase += port * 0x100; - up->iotype = UPIO_MEM32; - up->regshift = 2; - up->irq = 4; - } -#endif - up->iobase = 0; - up->serial_in = ce4100_mem_serial_in; - up->serial_out = ce4100_mem_serial_out; - - *capabilities |= (1 << 12); -} - -static __init void sdv_serial_fixup(void) -{ - serial8250_set_isa_configurator(ce4100_serial_fixup); -} - -#else -static inline void sdv_serial_fixup(void) {}; -#endif - static void __init sdv_arch_setup(void) { sdv_serial_fixup(); diff --git a/arch/x86/platform/efi/efi_64.c b/arch/x86/platform/efi/efi_64.c index e7e8f77f77f8..b4409df2105a 100644 --- a/arch/x86/platform/efi/efi_64.c +++ b/arch/x86/platform/efi/efi_64.c @@ -216,8 +216,8 @@ int __init efi_setup_page_tables(unsigned long pa_memmap, unsigned num_pages) * When SEV-ES is active, the GHCB as set by the kernel will be used * by firmware. Create a 1:1 unencrypted mapping for each GHCB. */ - if (sev_es_efi_map_ghcbs(pgd)) { - pr_err("Failed to create 1:1 mapping for the GHCBs!\n"); + if (sev_es_efi_map_ghcbs_cas(pgd)) { + pr_err("Failed to create 1:1 mapping for the GHCBs and CAs!\n"); return 1; } |