| Age | Commit message (Collapse) | Author |
|---|
|
The ice_vsi_add_vlan() function is used to add a VLAN filter for the target
VSI. This function prepares a filter in the switch table for the given VSI.
If it succeeds, the vsi->num_vlan counter is incremented.
It is not considered an error to add a VLAN which already exists in the
switch table, so the function explicitly checks and ignores -EEXIST. The
vsi->num_vlan counter is still incremented.
This seems incorrect, as it means we can double-count in the case where the
same VLAN is added twice by the caller. The actual table will have one less
filter than the count.
The ice_vsi_del_vlan() function similarly checks and handles the -ENOENT
condition for when deleting a filter that doesn't exist. This flow only
decrements the vsi->num_vlan if it actually deleted a filter.
The vsi->num_vlan counter is used only in a few places, primarily related
to tracking the number of non-zero VLANs. If the vsi->num_vlans gets out of
sync, then ice_vsi_num_non_zero_vlans() will incorrectly report more VLANs
than are present, and ice_vsi_has_non_zero_vlans() could return true
potentially in cases where there are only VLAN 0 filters left.
Fix this by only incrementing the vsi->num_vlan in the case where we
actually added an entry, and not in the case where the entry already
existed.
Fixes: a1ffafb0b4a4 ("ice: Support configuring the device to Double VLAN Mode")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240523-net-2024-05-23-intel-net-fixes-v1-2-17a923e0bb5f@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, idpf enables NAPI and interrupts prior to allocating Rx
buffers.
This may lead to frame loss (there are no buffers to place incoming
frames) and even crashes on quick ifup-ifdown. Interrupts must be
enabled only after all the resources are here and available.
Split interrupt init into two phases: initialization and enabling,
and perform the second only after the queues are fully initialized.
Note that we can't just move interrupt initialization down the init
process, as the queues must have correct a ::q_vector pointer set
and NAPI already added in order to allocate buffers correctly.
Also, during the deinit process, disable HW interrupts first and
only then disable NAPI. Otherwise, there can be a HW event leading
to napi_schedule(), but the NAPI will already be unavailable.
Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport")
Reported-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240523-net-2024-05-23-intel-net-fixes-v1-1-17a923e0bb5f@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the tagged commit, @netdev got documented twice and the kdoc
script didn't notice that. Remove the second description added later
and move the initial one according to the field position.
After merging commit 5f8e4007c10d ("kernel-doc: fix
struct_group_tagged() parsing"), kdoc requires to describe struct
groups as well. &page_pool_params has 2 struct groups which
generated new warnings, describe them to resolve this.
Fixes: 403f11ac9ab7 ("page_pool: don't use driver-set flags field directly")
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20240524112859.2757403-1-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.
Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When fec_probe() fails or fec_drv_remove() needs to release the
fec queue and remove a NAPI context, therefore add a function
corresponding to fec_enet_init() and call fec_enet_deinit() which
does the opposite to release memory and remove a NAPI context.
Fixes: 59d0f7465644 ("net: fec: init multi queue date structure")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240524050528.4115581-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
constraints
The child nodes are missing "additionalProperties" constraints which
means any undocumented properties or child nodes are allowed. Add the
constraints and all the undocumented properties exposed by the fix.
Fixes: f562202fedad ("dt-bindings: net: pse-pd: Add bindings for TPS23881 PSE controller")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240523171750.2837331-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"additionalProperties" constraints
The child nodes are missing "additionalProperties" constraints which
means any undocumented properties or child nodes are allowed. Add the
constraints, and fix the fallout of wrong manager node regex and
missing properties.
Fixes: 9c1de033afad ("dt-bindings: net: pse-pd: Add bindings for PD692x0 PSE controller")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240523171732.2836880-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jason commit made checks against ACK sequence less strict
and can be exploited by attackers to establish spoofed flows
with less probes.
Innocent users might use tcp_rmem[1] == 1,000,000,000,
or something more reasonable.
An attacker can use a regular TCP connection to learn the server
initial tp->rcv_wnd, and use it to optimize the attack.
If we make sure that only the announced window (smaller than 65535)
is used for ACK validation, we force an attacker to use
65537 packets to complete the 3WHS (assuming server ISN is unknown)
Fixes: 378979e94e95 ("tcp: remove 64 KByte limit for initial tp->rcv_wnd value")
Link: https://datatracker.ietf.org/meeting/119/materials/slides-119-tcpm-ghost-acks-00
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/r/20240523130528.60376-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Syzkaller was able to trigger
kernel BUG at net/core/gro.c:424 !
RIP: 0010:gro_pull_from_frag0 net/core/gro.c:424 [inline]
RIP: 0010:gro_try_pull_from_frag0 net/core/gro.c:446 [inline]
RIP: 0010:dev_gro_receive+0x242f/0x24b0 net/core/gro.c:571
Due to using an incorrect NAPI_GRO_CB(skb)->network_offset.
The referenced commit sets this offset to 0 in skb_gro_reset_offset.
That matches the expected case in dev_gro_receive:
pp = INDIRECT_CALL_INET(ptype->callbacks.gro_receive,
ipv6_gro_receive, inet_gro_receive,
&gro_list->list, skb);
But syzkaller injected an skb with protocol ETH_P_TEB into an ip6gre
device (by writing the IP6GRE encapsulated version to a TAP device).
The result was a first call to eth_gro_receive, and thus an extra
ETH_HLEN in network_offset that should not be there. First issue hit
is when computing offset from network header in ipv6_gro_pull_exthdrs.
Initialize both offsets in the network layer gro_receive.
This pairs with all reads in gro_receive, which use
skb_gro_receive_network_offset().
Fixes: 186b1ea73ad8 ("net: gro: use cb instead of skb->network_header")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
CC: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240523141434.1752483-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cited commit started returning an error when user space requests to dump
the interface's IPv4 addresses and IPv4 is disabled on the interface.
Restore the previous behavior and do not return an error.
Before cited commit:
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether e2:40:68:98:d0:18 brd ff:ff:ff:ff:ff:ff
inet6 fe80::e040:68ff:fe98:d018/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
# ip link set dev dummy1 mtu 67
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 67 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether e2:40:68:98:d0:18 brd ff:ff:ff:ff:ff:ff
After cited commit:
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 32:2d:69:f2:9c:99 brd ff:ff:ff:ff:ff:ff
inet6 fe80::302d:69ff:fef2:9c99/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
# ip link set dev dummy1 mtu 67
# ip address show dev dummy1
RTNETLINK answers: No such device
Dump terminated
With this patch:
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether de:17:56:bb:57:c0 brd ff:ff:ff:ff:ff:ff
inet6 fe80::dc17:56ff:febb:57c0/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
# ip link set dev dummy1 mtu 67
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 67 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether de:17:56:bb:57:c0 brd ff:ff:ff:ff:ff:ff
I fixed the exact same issue for IPv6 in commit c04f7dfe6ec2 ("ipv6: Fix
address dump when IPv6 is disabled on an interface"), but noted [1] that
I am not doing the change for IPv4 because I am not aware of a way to
disable IPv4 on an interface other than unregistering it. I clearly
missed the above case.
[1] https://lore.kernel.org/netdev/20240321173042.2151756-1-idosch@nvidia.com/
Fixes: cdb2f80f1c10 ("inet: use xa_array iterator to implement inet_dump_ifaddr()")
Reported-by: Carolina Jubran <cjubran@nvidia.com>
Reported-by: Yamen Safadi <ysafadi@nvidia.com>
Tested-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240523110257.334315-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-05-27
We've added 15 non-merge commits during the last 7 day(s) which contain
a total of 18 files changed, 583 insertions(+), 55 deletions(-).
The main changes are:
1) Fix broken BPF multi-uprobe PID filtering logic which filtered by thread
while the promise was to filter by process, from Andrii Nakryiko.
2) Fix the recent influx of syzkaller reports to sockmap which triggered
a locking rule violation by performing a map_delete, from Jakub Sitnicki.
3) Fixes to netkit driver in particular on skb->pkt_type override upon pass
verdict, from Daniel Borkmann.
4) Fix an integer overflow in resolve_btfids which can wrongly trigger build
failures, from Friedrich Vock.
5) Follow-up fixes for ARC JIT reported by static analyzers,
from Shahab Vahedi.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Cover verifier checks for mutating sockmap/sockhash
Revert "bpf, sockmap: Prevent lock inversion deadlock in map delete elem"
bpf: Allow delete from sockmap/sockhash only if update is allowed
selftests/bpf: Add netkit test for pkt_type
selftests/bpf: Add netkit tests for mac address
netkit: Fix pkt_type override upon netkit pass verdict
netkit: Fix setting mac address in l2 mode
ARC, bpf: Fix issues reported by the static analyzers
selftests/bpf: extend multi-uprobe tests with USDTs
selftests/bpf: extend multi-uprobe tests with child thread case
libbpf: detect broken PID filtering logic for multi-uprobe
bpf: remove unnecessary rcu_read_{lock,unlock}() in multi-uprobe attach logic
bpf: fix multi-uprobe PID filtering logic
bpf: Fix potential integer overflow in resolve_btfids
MAINTAINERS: Add myself as reviewer of ARM64 BPF JIT
====================
Link: https://lore.kernel.org/r/20240527203551.29712-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Radxa ROCK S0 is a single-board computer based on the Rockchip RK3308B
SoC in an ultra-compact form factor.
Add initial support for eMMC, SD-card, Ethernet, WiFi/BT and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521212247.1240226-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree binding for the Radxa ROCK S0 board.
Radxa ROCK S0 is a single-board computer based on the Rockchip RK3308B
SoC in an ultra-compact form factor.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240521212247.1240226-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Update WiFi SDIO and BT UART related props to better reflect details
about the optional onboard RTL8723DS WiFi/BT module.
Also correct the compatible used for bluetooth to match the WiFi/BT
module used on the board.
Fixes: bc3753aed81f ("arm64: dts: rockchip: rock-pi-s add more peripherals")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-14-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The VCCIO4 io-domain used for WiFi/BT is using 1v8 IO signal voltage.
Add io-domains node with the VCCIO supplies connected on the board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-13-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add a disabled RK3308 IO voltage domains node to SoC DT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-12-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3308 SoC contains a controller for one-time-programmable memory,
add a device node for it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-9-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Be explicit about the Ethernet port and define mdio and ethernet-phy
nodes in the device tree for ROCK Pi S.
Fixes: bc3753aed81f ("arm64: dts: rockchip: rock-pi-s add more peripherals")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-8-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
UAR0 CTS/RTS is not wired to any pin and is not used for the default
serial console use of UART0 on ROCK Pi S.
Override the SoC defined pinctrl props to limit configuration of the
two xfer pins wired to one of the GPIO pin headers.
Fixes: 2e04c25b1320 ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-6-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add cap-mmc-highspeed to allow use of high speed MMC mode using an eMMC
to uSD board. Use disable-wp to signal that no physical write-protect
line is present. Also add vcc_io used for card and IO line power as
vmmc-supply.
Fixes: 2e04c25b1320 ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Radxa ZERO 3W/3E is an ultra-small, high-performance single board
computer based on the Rockchip RK3566, with a compact form factor and
rich interfaces.
The ZERO 3W and ZERO 3E are basically the same size and model, but
differ only in storage and network interfaces.
- eMMC (3W)
- SD-card (both)
- Ethernet (3E)
- WiFi/BT (3W)
Add initial support for eMMC, SD-card, Ethernet, HDMI and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521202810.1225636-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree binding documentation for Radxa ZERO 3W/3E boards.
The Radxa ZERO 3W/3E is an ultra-small, high-performance single board
computer based on the Rockchip RK3566, with a compact form factor and
rich interfaces.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240521202810.1225636-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
MODULE_DESCRIPTION() was optional until it became mandatory and
flagged as an error by 'make W=1'.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240527194414.166156-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the arbitrary Intel convention order to allow for easier grep.
MODULE_LICENSE
MODULE_DESCRIPTION
MODULE_IMPORT
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240527194414.166156-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The module information is spread across files, group in a single
location. For maintenability and alignment, the arbitrary Intel
convention is used with the following order:
MODULE_LICENSE
MODULE_DESCRIPTION
MODULE_IMPORT
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240527194414.166156-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This file is part of the snd-sof module, there's no reason to re-add the
MODULE_LICENSE here.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240527194414.166156-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
blk_stats_alloc_enable was used for block hybrid poll, the related
function definition was removed by patch:
commit 54bdd67d0f88 ("blk-mq: remove hybrid polling")
but the function declaration was not deleted.
Signed-off-by: hexue <xue01.he@samsung.com>
Link: https://lore.kernel.org/r/20240527084533.1485210-1-xue01.he@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When powering on a null_blk device that is not already on, the return
value ret that is initialized to be count is reused to check the return
value of null_add_dev(), leading to nullb_device_power_store() to return
null_add_dev() return value (0 on success) instead of "count".
So make sure to set ret to be equal to count when there are no errors.
Fixes: a2db328b0839 ("null_blk: fix null-ptr-dereference while configuring 'power' and 'submit_queues'")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Link: https://lore.kernel.org/r/20240527043445.235267-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Verifier enforces that only certain program types can mutate sock{map,hash}
maps, that is update it or delete from it. Add test coverage for these
checks so we don't regress.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20240527-sockmap-verify-deletes-v1-3-944b372f2101@cloudflare.com
|
|
This reverts commit ff91059932401894e6c86341915615c5eb0eca48.
This check is no longer needed. BPF programs attached to tracepoints are
now rejected by the verifier when they attempt to delete from a
sockmap/sockhash maps.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20240527-sockmap-verify-deletes-v1-2-944b372f2101@cloudflare.com
|
|
We have seen an influx of syzkaller reports where a BPF program attached to
a tracepoint triggers a locking rule violation by performing a map_delete
on a sockmap/sockhash.
We don't intend to support this artificial use scenario. Extend the
existing verifier allowed-program-type check for updating sockmap/sockhash
to also cover deleting from a map.
From now on only BPF programs which were previously allowed to update
sockmap/sockhash can delete from these map types.
Fixes: ff9105993240 ("bpf, sockmap: Prevent lock inversion deadlock in map delete elem")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Reported-by: syzbot+ec941d6e24f633a59172@syzkaller.appspotmail.com
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: syzbot+ec941d6e24f633a59172@syzkaller.appspotmail.com
Acked-by: John Fastabend <john.fastabend@gmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=ec941d6e24f633a59172
Link: https://lore.kernel.org/bpf/20240527-sockmap-verify-deletes-v1-1-944b372f2101@cloudflare.com
|
|
Add device tree source for the TP-Link Archer AX55 v1 [1]
which is a dual-band WiFi router based on the IPQ5018 SoC.
At the moment, only the UART, the GPIO LEDs and buttons
are usable, but it makes it possible to boot an initramfs
image on the device.
The device tree can be extended in the future, once support
for other periherals will be available for the platform.
1. https://www.tp-link.com/en/home-networking/wifi-router/archer-ax55/v1/
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240326-archer-ax55-v1-v4-2-dc5b54a4bb00@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Document the TP-Link Archer AX55 v1 which is a dual-band
WiFi router based on the IPQ5018 SoC.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240326-archer-ax55-v1-v4-1-dc5b54a4bb00@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the devicetree for this "phablet" using the Snapdragon 800 SoC.
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
[luca@z3ntu.xyz: clean up, prepare for upstream]
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240314-samsung-hlte-v2-2-84094b41c033@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the compatible for this Samsung smartphone ("phablet" as it was
named in that era).
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20240314-samsung-hlte-v2-1-84094b41c033@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The PCIe EP controller on SA8775P supports cache coherency, hence add
the "dma-coherent" property to mark it as such.
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1710166298-27144-4-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Connect the panel with the backlight nodes so that the backlight can be
turned off when the display is blanked.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240220-lm3630a-fixups-v1-4-9ca62f7e4a33@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add support for this tablet based on the MSM8226 SoC, codenamed
"milletwifi".
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bryant Mairs <bryant@mai.rs>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240219214643.197116-3-bryant@mai.rs
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add binding documentation for Samsung Galaxy Tab 4 8.0 Wi-Fi
tablet which is based on Snapdragon 400 (apq8026) SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Bryant Mairs <bryant@mai.rs>
Link: https://lore.kernel.org/r/20240219214643.197116-2-bryant@mai.rs
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The IPQ95xx uses an IPQ4019 compatible MDIO controller that is already
supported. Add a DT node to expose it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://lore.kernel.org/r/20240507024758.2810514-2-mr.nuke.me@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add node describing wireless connectivity subsystem.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Link: https://lore.kernel.org/r/20240508163455.8757-5-a39.skl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add Adreno GPU node.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Link: https://lore.kernel.org/r/20240508163455.8757-4-a39.skl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add MDSS nodes to support displays on MSM8976 SoC.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Link: https://lore.kernel.org/r/20240508163455.8757-3-a39.skl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the nodes describing the apps and gpu iommu and its context banks
that are found on msm8976 SoCs.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Link: https://lore.kernel.org/r/20240508163455.8757-2-a39.skl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the different services found on APR on some devices with SC7280 SoC.
Additionally add an empty sound node in the root node as is seen on
other SoC dtsi files so device dt's can easily use that.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240510-sc7280-apr-v1-1-e9eabda05f85@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
We recently upgraded the view of ESR_EL2 to 64bit, in keeping with
the requirements of the architecture.
However, the AArch32 emulation code was left unaudited, and the
(already dodgy) code that triages whether a trap is spurious or not
(because the condition code failed) broke in a subtle way:
If ESR_EL2.ISS2 is ever non-zero (unlikely, but hey, this is the ARM
architecture we're talking about), the hack that tests the top bits
of ESR_EL2.EC will break in an interesting way.
Instead, use kvm_vcpu_trap_get_class() to obtain the EC, and list
all the possible ECs that can fail a condition code check.
While we're at it, add SMC32 to the list, as it is explicitly listed
as being allowed to trap despite failing a condition code check (as
described in the HCR_EL2.TSC documentation).
Fixes: 0b12620fddb8 ("KVM: arm64: Treat ESR_EL2 as a 64-bit register")
Cc: stable@vger.kernel.org
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240524141956.1450304-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
It appears that we don't allow a vcpu to be restored in AArch32
System mode, as we *never* included it in the list of valid modes.
Just add it to the list of allowed modes.
Fixes: 0d854a60b1d7 ("arm64: KVM: enable initialization of a 32bit vcpu")
Cc: stable@vger.kernel.org
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240524141956.1450304-3-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
On most devices, TZ seems to be blocking access to the PSHOLD reboot
register. This seems to be TZ, as even kicking the hypervisor doesn't
seem to make it writable.
Fixes: 865ff2e6f5da ("arm64: dts: qcom: sc8280xp: Add PS_HOLD restart")
Reported-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Link: https://lore.kernel.org/r/20240510-topic-8280_off-v1-1-bcc70cda449e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
When userspace writes to one of the core registers, we make
sure to narrow the corresponding GPRs if PSTATE indicates
an AArch32 context.
The code tries to check whether the context is EL0 or EL1 so
that it narrows the correct registers. But it does so by checking
the full PSTATE instead of PSTATE.M.
As a consequence, and if we are restoring an AArch32 EL0 context
in a 64bit guest, and that PSTATE has *any* bit set outside of
PSTATE.M, we narrow *all* registers instead of only the first 15,
destroying the 64bit state.
Obviously, this is not something the guest is likely to enjoy.
Correctly masking PSTATE to only evaluate PSTATE.M fixes it.
Fixes: 90c1f934ed71 ("KVM: arm64: Get rid of the AArch32 register mapping code")
Reported-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240524141956.1450304-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Follow other Qualcomm platforms and rename pm8150b_role_switch_in to
pm8150_hs_in. Corresponding port is described as HS port rather than
role switching.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240512-typec-fix-sm8250-v4-9-ad153c747a97@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
