| Age | Commit message (Collapse) | Author |
|---|
|
The defaults for this SoC are configured for overdrive mode, but
the VPU clocks are currently configured for nominal mode.
Increase VPU_G1_CLK_ROOT to 800MHZ from 600MHz,
Increase VPU_G2_CLK_ROOT to 700MHZ from 500MHz, and
Increase VPU_BUS_CLK_ROOT to 800MHz from 600MHz.
This requires adjusting the clock parents. Since there is already
800MHz clock references, move the VPU_BUS and G1 clocks to it.
This frees up the VPU_PLL to be configured at 700MHz to run
the G2 clock at 700MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In preparation for increasing the default VPU clocks to overdrive,
configure the nominal values first to avoid running the nominal
devices out of spec when imx8mp.dtsi is changed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The VPU_PLL clock must be set before the VPU_BUS clock which is derived
from the VPU_PLL clock else the VPU_BUS clock is 300MHz and not 600MHz.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GPCv2 G1, G2 and VC8000E power-domain don't need to reference the
VPUMIX power-domain nor their module clocks since the power and reset
handling is done by the VPUMIX blkctrl driver.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
LGTM: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The iMX8QXP and iMX8QM have a CAAM (Cryptographic Acceleration and
Assurance Module) like many other iMXs.
Add the definitions for it.
Job Rings 0 and 1 are bound to the SECO (Security Controller) ARM core
and are not exposed outside it. There's no point to define them in the
bindings as they cannot be used outside the SECO.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In AM69 SoC there are 4 instances of the 4 lane SERDES. So in
"serdes_ln_ctrl" node there are total 16 entries in "mux-reg-mask"
property. But "idle-states" is defined only for the lanes of first two
SERDES instances. SERDES lane mapping is left at its reset state of
"zero" for all four lanes of SERDES2 and SERDES4. The reset state of
"zero" corresponds to the following configuration:
Lanes 0 and 1 of SERDES2 are unused
CPSW MAC Ports 1 and 2 mapped to lanes 2 and 3 of SERDES2
EDP Lanes 0, 1, 2 and 3 mapped to lanes 0, 1, 2 and 3 of SERDES4
For completeness, define the "idle-states" for the lanes of remaining
SERDES instances.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250708113942.4137917-1-h-salunke@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used during the early stages of
bootup by the bootloaders.
This includes the console UART along with the SD and eMMC nodes and its
required regulators for the 3v3 to 1v8 transition and the various nodes
for Ethernet booting.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250710-62a-uboot-cleanup-v2-1-9e04a7db1f54@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used in the bootloader for the
AM654 reference board.
UARTs used as a console, the SD and eMMC nodes along with the needed
regulators for UHS modes, and the needed nodes for OSPI boot are all
marked with 'bootph-all' to handle the various boot modes the board is
capable of
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250710-65-boot-phases-v2-2-d431deb88783@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all required nodes for all AM65x platforms.
Mark the mailbox and ring accelerators needed to communicate the with
various vendor firmware and the power, clock and reset nodes along with
the MMR for the chip-id to facilitate detecting the SoC and which
silicon version during the early stages of bootup with 'bootph-all' as
they are used during all phases of bootup
--
Changes in v2:
- removed tag from &mcu_udmap{} node
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250710-65-boot-phases-v2-1-d431deb88783@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Remove unnecessary empty line in stm32mp251.dtsi
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250515151238.2.Ia426b4ef1d1200247a950ef9abd54a94dc520acb@changeid
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Remove always-on on generic ARM timer as the clock source provided by
STGEN is deactivated in low power mode, STOP1 by example.
Fixes: 5d30d03aaf78 ("arm64: dts: st: introduce stm32mp25 SoCs family")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250515151238.1.I85271ddb811a7cf73532fec90de7281cb24ce260@changeid
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable HDMI input port of the RK3588 EVB1.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250704-rk3588-evb1-hdmi-rx-v1-1-248315c36ccd@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Old revisions of the ROCK 4D board have a dedicated crystal to
supply the RTL8211F PHY's 25MHz clock input. At least some newer
revisions instead use REFCLKO25M_GMAC0_OUT. The DT already has
this half-prepared, but there are some issues:
1. The DT relies on auto-selecting the right PHY driver, which
requires that it works good enough to read the ID registers.
This does not work without the clock, which is handled by
the PHY driver. By updating the compatible to contain the
RTL8211F IDs, so that the operating system can choose the
right PHY driver without relying on a pre-powered PHY.
2. Despite the name REFCLKO25M_GMAC0_OUT could also provide a
different frequency, so ensure it is explicitly set to 25
MHz as expected by the PHY.
3. While at it switch from deprecated "enable-gpio" to standard
"enable-gpios".
Fixes: a0fb7eca9c09 ("arm64: dts: rockchip: Add Radxa ROCK 4D device tree")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250704-rk3576-rock4d-phy-handling-fixes-v1-1-1d64130c4139@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the w552793baa 1080x1920 dsi panel on rk3568 evb1.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250706113831.330799-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This device supports removable UFS chips, add support for it.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Link: https://lore.kernel.org/r/20250708155010.401446-1-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Ethernet boot requires CPSW nodes to be present starting from R5 SPL
stage. Add bootph-all property to required nodes to enable Ethernet boot
for SK-AM69.
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20250709105326.232608-5-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Ethernet boot requires CPSW nodes to be present starting from R5 SPL
stage. Add bootph-all property to required nodes to enable Ethernet boot
for J722S-EVM.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20250709105326.232608-4-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Ethernet boot requires CPSW nodes to be present starting from R5 SPL
stage. Add bootph-all property to required nodes to enable Ethernet boot
for AM62P5-SK.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20250709105326.232608-3-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Ethernet boot
Ethernet boot requires CPSW nodes to be present starting from R5 SPL
stage. Add bootph-all property to required nodes to enable Ethernet boot
on SK-AM68.
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20250709105326.232608-2-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
AM62D-EVM evaluation module (EVM) is a low-cost expandable platform board
designed for AM62D2 SoC from TI. It supports the following interfaces:
* 4 GB LPDDR4 RAM
* x2 Gigabit Ethernet expansion connectors
* x4 3.5mm TRS Audio Jack Line In
* x4 3.5mm TRS Audio Jack Line Out
* x2 Audio expansion connectors
* x1 Type-A USB 2.0, x1 Type-C dual-role device (DRD) USB 2.0
* x1 UHS-1 capable micro SD card slot
* 32 GB eMMC Flash
* 512 Mb OSPI NOR flash
* x4 UARTs via USB 2.0-B
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
Although AM62D2 and AM62A7 differ in peripheral capabilities example
multimedia, VPAC, and display subsystems, the core architecture remains
same. To reduce duplication, AM62D support reuses the AM62A dtsi and the
necessary overrides will be handled in SOC specific dtsi file and a
board specific dts.
Add basic support for AM62D2-EVM.
Schematics Link - https://www.ti.com/lit/zip/sprcal5
Signed-off-by: Paresh Bhagat <p-bhagat@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250708085839.1498505-5-p-bhagat@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Update k3-pinctrl file to include pin definitions for AM62D2 family of
SoCs.
Signed-off-by: Paresh Bhagat <p-bhagat@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250708085839.1498505-4-p-bhagat@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add bootph property directly into the original definitions of relevant
nodes (e.g., power domains, USB controllers, and other peripherals)
within their respective DTSI files (ex. main, mcu, and wakeup) for
am62a.
By defining bootph in the nodes source definitions instead of appending
it later in final DTS files, this change ensures that the property is
inherently present wherever the nodes are reused across derived device
trees.
Signed-off-by: Paresh Bhagat <p-bhagat@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250708085839.1498505-2-p-bhagat@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
While the TI AM62P supports a junction temperature (Tj) of up to 125°C
for industrial and automotive parts, Toradex Verdin-AM62P hardware
lifetime guarantees consider a 105°C Tj. Change the passive trip points
to 95°C and the critical trip points to 105°C to be compliant with the
hardware specifications.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Link: https://lore.kernel.org/r/20250623-b4-verdin-am62p-cooling-device-v1-2-cc185ba5843d@toradex.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable throttling down the CPU frequency when an alert temperature
threshold is reached before the critical temperature for shutdown.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Link: https://lore.kernel.org/r/20250623-b4-verdin-am62p-cooling-device-v1-1-cc185ba5843d@toradex.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add DT node for PBIST_14 that is responsible for triggering the PBIST
self-tests for the MAIN_R5_2_x cores.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20250605063506.2005637-3-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
For eMMC, High Speed DDR mode is not supported [0], so remove
mmc-ddr-1_8v flag which adds the capability.
[0] https://www.ti.com/lit/gpn/am625
Fixes: c37c58fdeb8a ("arm64: dts: ti: k3-am62: Add more peripheral nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250707191250.3953990-1-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
This moves pinmux child nodes for sdhci0 node from k3-am62x-sk-common
to each top level board file. This is needed since we require internal
pullups for AM62x SK and not for AM62 LP SK since it has external
pullups on DATA 1-7.
Internal pulls are required for AM62 SK as per JESD84 spec
recommendation to prevent unconnected lines floating.
Fixes: d19a66ae488a ("arm64: dts: ti: k3-am625-sk: Enable on board peripherals")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250707190830.3951619-1-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
main_uart1 reserved for TIFS firmware traces is routed to the
onboard FT4232 via a FET switch which is connected to pin A21 and
B21 of the SoC and not E17 and C17. Fix it.
Fixes: cf39ff15cc01a ("arm64: dts: ti: k3-am62a7-sk: Describe main_uart1 and wkup_uart")
Cc: stable@vger.kernel.org
Signed-off-by: Hong Guan <hguan@ti.com>
[bb@ti.com: expanded commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250707-uart-fixes-v1-1-8164147218b0@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Allow overlays to be applied to any DTB without manually enabling it
for each file. This adds around ~10% to the total size of the DTB files
on average.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250702145314.71996-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
PWM_3_DSI is used as the HDMI Hot-Plug Detect (HPD) GPIO for the Verdin
DSI-to-HDMI adapter. After the commit 33bab9d84e52 ("arm64: dts: ti:
k3-am62p: fix pinctrl settings"), the pin was incorrectly set as output
without RXACTIVE, breaking HPD detection and display functionality.
The issue was previously hidden and worked by chance before the mentioned
pinctrl fix.
Fix the pinmux configuration to correctly set PWM_3_DSI GPIO as an input.
Fixes: 87f95ea316ac ("arm64: dts: ti: Add Toradex Verdin AM62P")
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20250703084534.1649594-1-parth105105@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Switch Schmitt Trigger functions for PIN_INPUT* macros by default. This is
HW PoR configuration, the slew rate requirements without ST enabled are
pretty tough for these devices. We've noticed spurious GPIO interrupts even
with noise-free edges but not meeting slew rate requirements (3.3E+6 V/s
for 3.3v LVCMOS).
It's not obvious why one might want to disable the PoR-enabled ST on any
pin. Just enable it by default. As it's not possible to provide OR-able
macros to disable the ST, shall anyone require it, provide a set of
new macros with _NOST suffix.
Fixes: fe49f2d776f7 ("arm64: dts: ti: Use local header for pinctrl register values")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20250701105437.3539924-1-alexander.sverdlin@siemens.com
[vigneshr@ti.com: Add Fixes tag]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The datasheets refer to the first Ethernet controller as GMAC0, not
EMAC0.
Fix the compatible string, node label and pinmux function name to match
what the datasheets use. A change to the device tree binding is sent
separately.
Fixes: 56766ca6c4f6 ("arm64: dts: allwinner: a523: Add EMAC0 ethernet MAC")
Fixes: acca163f3f51 ("arm64: dts: allwinner: a527: add EMAC0 to Radxa A5E board")
Fixes: c6800f15998b ("arm64: dts: allwinner: t527: add EMAC0 to Avaota-A1 board")
Link: https://patch.msgid.link/20250628054438.2864220-3-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Enable MT25QU512ABB8E12 FLASH connected to XSPI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250704140823.163572-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable MT25QU512ABB8E12 FLASH connected to XSPI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250704140823.163572-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add XSPI node to RZ/V2H(P) ("R9A09G057") SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250704140823.163572-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add XSPI node to RZ/V2N ("R9A09G056") SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250704140823.163572-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Rename the GBETH1 pinctrl node from "eth0" to "eth1" to avoid duplicate
node names in the DT and correctly reflect the label "eth1_pins".
Fixes: f111192baa80 ("arm64: dts: renesas: r9a09g056n48-rzv2n-evk: Enable GBETH")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250703235544.715433-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Rename the GBETH1 pinctrl node from "eth0" to "eth1" to avoid duplicate
node names in the DT and correctly reflect the label "eth1_pins".
Fixes: 802292ee27a7 ("arm64: dts: renesas: r9a09g057h44-rzv2h-evk: Enable GBETH")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250703235544.715433-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The target to consider the dtbo file for installation is missing, add
it.
Fixes: a719915e76f2 ("arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/20250701112612.3957799-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable the Gigabit Ethernet Interfaces (GBETH) populated on the RZ/G3E SMARC EVK
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250702005706.1200059-5-john.madieu.xa@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
RZ/G3E SMARC EVK has 3 user buttons called USER_SW1, USER_SW2 and
USER_SW3 and SLEEP button with NMI support. Add a DT node in device tree
to instantiate the gpio-keys driver for these buttons.
The system can enter into STR state by pressing the sleep button and
wakeup from STR is done by pressing power button. The USER_SW{1,2,3}
configured as wakeup-source, so it can wakeup the system during s2idle.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250702092755.70847-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add in mt8395-genio-1200-evk devicetree file a sub node in pmic for
the mt6359-keys compatible to add the Power and Home MT6359 PMIC keys
support.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Link: https://lore.kernel.org/r/20250703-add-mt6359-pmic-keys-support-v1-3-21a4d2774e34@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Add in mt8390-genio-common dtsi file the support of Home MT6359 PMIC
key.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Link: https://lore.kernel.org/r/20250703-add-mt6359-pmic-keys-support-v1-2-21a4d2774e34@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Bananapi R4 has a green and a blue led which can be switched by gpio.
Green led is for running state so default on.
Green led also shares pin with eeprom writeprotect where led off allows
writing to eeprom.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250706132213.20412-14-linux@fw-web.de
[Angelo: Fixed missing dt-bindings/leds/common.h header inclusion]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
This adds the USB support for the s32g2 and s32g3 SoCs.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/e3e5041e-254d-44c3-b645-532d4d7a8f9e@sabinyo.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pins were moved from SoC dtsi to Board level dtsi without cleaning up
to needed ones. Drop the unused pins now.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250706132213.20412-13-linux@fw-web.de
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
CCI requires proc-supply. Add it on board level.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250706132213.20412-12-linux@fw-web.de
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Add cci devicetree node for cpu frequency scaling.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250706132213.20412-9-linux@fw-web.de
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Introduce ethernet controller nodes to EN7581 SoC and EN7581 evaluation
board.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20250520-en7581-net-v1-1-5317f8e829ad@kernel.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
fail-needs-probe
Different Spherion variants use different trackpads on the same I2C2
bus. Instead of enabling all of them by default, mark them as
"fail-needs-probe" and let the implementation determine which one is
actually present.
Additionally, move the trackpad pinctrl entry back to the individual
trackpad nodes.
Signed-off-by: Laura Nao <laura.nao@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250318102259.189289-3-laura.nao@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
