| Age | Commit message (Collapse) | Author |
|---|
|
Setup USB2 to act in "HOST" mode by default.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix SB-SOM EEPROM I2C address
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Revert commit 7cd6ca770d1b ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit") It was already done and it is
just a duplicate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.
Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.
While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.
and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.
Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
|
|
No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec5047a ("net: phy: Use interrupts when available in NOLINK state")
disables polling.
Cc: <stable@vger.kernel.org> # 4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
After 57a38effa598 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.
The phy IRQ and associated pinmux node is also added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
|
|
Properly use qiaodian as the vendor prefix for the panel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Change instance id of DBGU to 45.
Signed-off-by: Mohamed Jamsheeth Hajanajubudeen <mohamedjamsheeth.hajanajubudeen@atmel.com>
Fixes: 7c661394c56c ("ARM: at91: dt: add device tree file for SAMA5D4 SoC")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Building with CONFIG_CC_STACKPROTECTOR_STRONG triggers protection code
generation under CONFIG_ARM_ATAG_DTB_COMPAT but this is too early for
being able to use any of the stack_chk code. Explicitly disable it for
only the atags_to_fdt bits.
Suggested-by: zhxihu <zhxihu@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang. Scanning also appears broken without this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 687c27676151 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
In order to set the currently platform dependent dmtimer
functions pointers as platform data for the pwm-omap-dmtimer
platform driver, add it to plat-omap auxdata_lookup table.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Here're a few gpio pin related fixes:
- remove pinctrl-0 definition from pinctrl, since those pins are used
in other places such as gpio-fan and regulators.
- keep initial state of power led
- fix for alarm pin of gpio-fan.
Fixes: dc57844a736f ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The GPIOs controlling the LEDs, listed below, are active high, not low:
- gpio-leds: "lswvl:red:alarm" pin
- gpio-leds: "lswvl:red:func" pin
- gpio-leds: "lswvl:amber:info" pin
- gpio-leds: "lswvl:blue:func" pin
- gpio-leds: "lswvl:red:hdderr{0,1}" pin
Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The GPIOs controlling the LEDs, listed below, are active high, not low:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr{0,1}" pin
Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin
definition:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr0" pin
- gpio-leds: "lswxl:red:hdderr1" pin
- gpio-fan: low/high/alarm pin
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Merge small final update from Andrew Morton:
- DAX feature work: add fsync/msync support
- kfree cleanup, MAINTAINERS update
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: return arch/sh to maintained state, with new maintainers
tree wide: use kvfree() than conditional kfree()/vfree()
dax: never rely on bh.b_dev being set by get_block()
xfs: call dax_pfn_mkwrite() for DAX fsync/msync
ext4: call dax_pfn_mkwrite() for DAX fsync/msync
ext2: call dax_pfn_mkwrite() for DAX fsync/msync
dax: add support for fsync/sync
mm: add find_get_entries_tag()
dax: support dirty DAX entries in radix tree
pmem: add wb_cache_pmem() to the PMEM API
dax: fix conversion of holes to PMDs
dax: fix NULL pointer dereference in __dax_dbg()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for fallout that we didn't catch in time in -next, or
smaller warning fixes that have been discovered since"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: qcom/spm: shut up uninitialized variable warning
ARM: realview: fix device tree build
ARM: debug-ll: fix BCM63xx entry for multiplatform
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
|
|
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.5
Correct extal1 frequency of armadillo800eva board
* tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With recent omap assembly fixes for CONFIG_DEBUG_RODATA, we can
now use DEBUG_RODATA. Let's enable ARM_KERNMEM_PERMS so that
DEBUG_RODATA gets selected by default. This way we can make sure
any related issues are caught early.
And while testing things on various devices, I noticed we're
missing few loadable modules to make things more usable:
- USB Ethernet for smsc75xx, we only have smsc97xx right now
- Basic USB serial drivers for things like ftdi and pl2303 ports
- Blinking leds with pca963x
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We don't want to write to .text so let's move ppa_zero_params and
ppa_por_params to .data and access them via pointers.
Note that I have not been able to test as we I don't have a HS
omap4 to test with. The code has been changed in similar way as
for omap3 though.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We don't want to write to .text, so let's move l2_inv_api_params
to .data and access it via a pointer.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We don't want to write to .text and we can move save_secure_ram_context
into .data as it all gets copied into SRAM anyways.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We don't want to write to .text section. Let's move l2dis_3630
to .data and access it via a pointer.
For calculating the offset, let's optimize out the add and do it
in ldr/str as suggested by Nicolas Pitre <nicolas.pitre@linaro.org>.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: stable@vger.kernel.org # v4.0+
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We don't want to be writing to .text so it can be set rodata.
Fix error "Unable to handle kernel paging request at virtual address
c012396c" in wait_dll_lock_timed if CONFIG_DEBUG_RODATA is selected.
As these counters are for debugging only and unused, we can just
remove them.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The legacy-style mailbox device creation is supported currently
only for OMAP3, as all other SoCs are DT-boot only. Even on this
SoC, there are no client drivers that utilize these mailbox devices.
So, clean up the legacy-style mailbox device instantiation logic.
The mailbox devices are already present and supported for the DT
boot on OMAP3.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is required to be able to send multiple messages to the WkupM3
after the mailbox usage logic adjustment in the wkup_m3_ipc driver.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is needed to achieve lower power numbers during CPU idle on
AM33xx.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Merge third patch-bomb from Andrew Morton:
"I'm pretty much done for -rc1 now:
- the rest of MM, basically
- lib/ updates
- checkpatch, epoll, hfs, fatfs, ptrace, coredump, exit
- cpu_mask simplifications
- kexec, rapidio, MAINTAINERS etc, etc.
- more dma-mapping cleanups/simplifications from hch"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (109 commits)
MAINTAINERS: add/fix git URLs for various subsystems
mm: memcontrol: add "sock" to cgroup2 memory.stat
mm: memcontrol: basic memory statistics in cgroup2 memory controller
mm: memcontrol: do not uncharge old page in page cache replacement
Documentation: cgroup: add memory.swap.{current,max} description
mm: free swap cache aggressively if memcg swap is full
mm: vmscan: do not scan anon pages if memcg swap limit is hit
swap.h: move memcg related stuff to the end of the file
mm: memcontrol: replace mem_cgroup_lruvec_online with mem_cgroup_online
mm: vmscan: pass memcg to get_scan_count()
mm: memcontrol: charge swap to cgroup2
mm: memcontrol: clean up alloc, online, offline, free functions
mm: memcontrol: flatten struct cg_proto
mm: memcontrol: rein in the CONFIG space madness
net: drop tcp_memcontrol.c
mm: memcontrol: introduce CONFIG_MEMCG_LEGACY_KMEM
mm: memcontrol: allow to disable kmem accounting for cgroup2
mm: memcontrol: account "kmem" consumers in cgroup2 memory controller
mm: memcontrol: move kmem accounting code to CONFIG_MEMCG
mm: memcontrol: separate kmem code from legacy tcp accounting code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v4.5 merge window:
Enumeration:
- Simplify config space size computation (Bjorn Helgaas)
- Avoid iterating through ROM outside the resource window (Edward O'Callaghan)
- Support PCIe devices with short cfg_size (Jason S. McMullan)
- Add Netronome vendor and device IDs (Jason S. McMullan)
- Limit config space size for Netronome NFP6000 family (Jason S. McMullan)
- Add Netronome NFP4000 PF device ID (Simon Horman)
- Limit config space size for Netronome NFP4000 (Simon Horman)
- Print warnings for all invalid expansion ROM headers (Vladis Dronov)
Resource management:
- Fix minimum allocation address overwrite (Christoph Biedl)
PCI device hotplug:
- acpiphp_ibm: Fix null dereferences on null ibm_slot (Colin Ian King)
- pciehp: Always protect pciehp_disable_slot() with hotplug mutex (Guenter Roeck)
- shpchp: Constify hpc_ops structure (Julia Lawall)
- ibmphp: Remove unneeded NULL test (Julia Lawall)
Power management:
- Make ASPM sysfs link_state_store() consistent with link_state_show() (Andy Lutomirski)
Virtualization
- Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 (Tim Sander)
MSI:
- Remove empty pci_msi_init_pci_dev() (Bjorn Helgaas)
- Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD (Grygorii Strashko)
- Initialize MSI capability for all architectures (Guilherme G. Piccoli)
- Relax msi_domain_alloc() to support parentless MSI irqdomains (Liu Jiang)
ARM Versatile host bridge driver:
- Remove unused pci_sys_data structures (Lorenzo Pieralisi)
Broadcom iProc host bridge driver:
- Hide CONFIG_PCIE_IPROC (Arnd Bergmann)
- Do not use 0x in front of %pap (Dmitry V. Krivenok)
- Update iProc PCIe device tree binding (Ray Jui)
- Add PAXC interface support (Ray Jui)
- Add iProc PCIe MSI device tree binding (Ray Jui)
- Add iProc PCIe MSI support (Ray Jui)
Freescale i.MX6 host bridge driver:
- Use gpio_set_value_cansleep() (Fabio Estevam)
- Add support for active-low reset GPIO (Petr Štetiar)
HiSilicon host bridge driver:
- Add support for HiSilicon Hip06 PCIe host controllers (Gabriele Paoloni)
Intel VMD host bridge driver:
- Export irq_domain_set_info() for module use (Keith Busch)
- x86/PCI: Allow DMA ops specific to a PCI domain (Keith Busch)
- Use 32 bit PCI domain numbers (Keith Busch)
- Add driver for Intel Volume Management Device (VMD) (Keith Busch)
Qualcomm host bridge driver:
- Document PCIe devicetree bindings (Stanimir Varbanov)
- Add Qualcomm PCIe controller driver (Stanimir Varbanov)
- dts: apq8064: add PCIe devicetree node (Stanimir Varbanov)
- dts: ifc6410: enable PCIe DT node for this board (Stanimir Varbanov)
Renesas R-Car host bridge driver:
- Add support for R-Car H3 to pcie-rcar (Harunobu Kurokawa)
- Allow DT to override default window settings (Phil Edworthy)
- Convert to DT resource parsing API (Phil Edworthy)
- Revert "PCI: rcar: Build pcie-rcar.c only on ARM" (Phil Edworthy)
- Remove unused pci_sys_data struct from pcie-rcar (Phil Edworthy)
- Add runtime PM support to pcie-rcar (Phil Edworthy)
- Add Gen2 PHY setup to pcie-rcar (Phil Edworthy)
- Add gen2 fallback compatibility string for pci-rcar-gen2 (Simon Horman)
- Add gen2 fallback compatibility string for pcie-rcar (Simon Horman)
Synopsys DesignWare host bridge driver:
- Simplify control flow (Bjorn Helgaas)
- Make config accessor override checking symmetric (Bjorn Helgaas)
- Ensure ATU is enabled before IO/conf space accesses (Stanimir Varbanov)
Miscellaneous:
- Add of_pci_get_host_bridge_resources() stub (Arnd Bergmann)
- Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask (Bjorn Helgaas)
- Fix all whitespace issues (Bogicevic Sasa)
- x86/PCI: Simplify pci_bios_{read,write} (Geliang Tang)
- Use to_pci_dev() instead of open-coding it (Geliang Tang)
- Use kobj_to_dev() instead of open-coding it (Geliang Tang)
- Use list_for_each_entry() to simplify code (Geliang Tang)
- Fix typos in <linux/msi.h> (Thomas Petazzoni)
- x86/PCI: Clarify AMD Fam10h config access restrictions comment (Tomasz Nowicki)"
* tag 'pci-v4.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183
PCI: Limit config space size for Netronome NFP4000
PCI: Add Netronome NFP4000 PF device ID
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
PCI: host: Add of_pci_get_host_bridge_resources() stub
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
PCI: rcar: Add Gen2 PHY setup to pcie-rcar
PCI: rcar: Add runtime PM support to pcie-rcar
PCI: designware: Make config accessor override checking symmetric
PCI: ibmphp: Remove unneeded NULL test
ARM: dts: ifc6410: enable PCIe DT node for this board
ARM: dts: apq8064: add PCIe devicetree node
PCI: hotplug: Use list_for_each_entry() to simplify code
PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar
PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers
PCI: Avoid iterating through memory outside the resource window
PCI: acpiphp_ibm: Fix null dereferences on null ibm_slot
...
|
|
As it happens, two obj-$(CONFIG_FOO) += foo.o variables are
above obj-y := core.o, which doesn't work: the += directives
need to add something to the build and doesn't work if obj-y
is not set first, so move the obj-y to be on top and everything
builds nicely again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"This includes fixes on top of the previous batch of PM+ACPI updates
and some new material as well.
From the new material perspective the most significant are the driver
core changes that should allow USB devices to stay suspended over
system suspend/resume cycles if they have been runtime-suspended
already beforehand. Apart from that, ACPICA is updated to upstream
revision 20160108 (cosmetic mostly, but including one fixup on top of
the previous ACPICA update) and there are some devfreq updates the
didn't make it before (due to timing).
A few recent regressions are fixed, most importantly in the cpuidle
menu governor and in the ACPI backlight driver and some x86 platform
drivers depending on it.
Some more bugs are fixed and cleanups are made on top of that.
Specifics:
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on top
of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates of
the ACPICA's copyright notices, a code fixup resulting from a
regression fix that was necessary in the upstream code only (the
regression fixed by it has never been present in Linux) and a
compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke it
on practically all architectures other than x86 and make a couple
of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether or
not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on the
problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up a
bit and update the MAINTAINERS information related to it (Chanwoo
Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas
Prabhu)"
* tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
cpuidle: menu: Avoid pointless checks in menu_select()
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
cpupower: Fix build error in cpufreq-info
cpuidle: Don't enable all governors by default
cpuidle: Default to ladder governor on ticking systems
time: nohz: Expose tick_nohz_enabled
ACPICA: Update version to 20160108
ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t'
ACPICA: Additional 2016 copyright changes
ACPICA: Reduce regression fix divergence from upstream ACPICA
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()"
ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit
ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses()
ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses"
ACPI / fan: Improve acpi_device_update_power error message
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
MAINTAINERS: Add devfreq-event entry
MAINTAINERS: Add missing git repository and directory for devfreq
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs because it makes sense to have them enabled on various
development or product boards. Too much to enumerate each here.
There's an introduction of a pxa_defconfig, since PXA finally will
allow building a shared kernel for all boards. With this, we can
hopefully remove a bunch of individual defconfigs down the road but it
requires a bit of real life testing and transition period"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: Add CONFIG_DEPRECATED_PARAM_STRUCT to netwinder_defconfig
ARM: multi_v7_defconfig: Add rockchip audio support
arm: multi_v7_defconfig: Add virtio drivers
ARM: zx_defconfig: remove CONFIG_MMC_DW_IDMAC
ARM: versatile: enable the right LEDs
ARM: pxa: add defconfig covering all the boards
ARM: versatile: select some defaults in defconfig
ARM: multi_v7_defconfig: Enable fan, sensors and audio for Odroid XU3
ARM: bcm2835: enable auxiliary spi driver in defconfig
ARM: bcm2835: enable all bcm2835-relevant in defconfig
ARM: default to multi_v7_defconfig
ARM: multi_v7_defconfig: enable rk808 clkout module
ARM: multi_v7_defconfig: enable rockchip crypto module
ARM: multi_v7_defconfig: enable Rockchip io-domain driver
ARM: multi_v7_defconfig: Enable generic SoC internal OMAP regulators
ARM: multi_v7_defconfig: Enable AM437x PMIC TPS65218
ARM: multi_v7_defconfig: enable TPS65217 regulator
ARM: realview: select apropriate targets
ARM: defconfig: qcom: Enable SSBI drivers
ARM: defconfig: Update qcom_defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: tango: Fix UP build issues
ARM: tango: pass ARM arch level for smc.S
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: OMAP2+: Add support for dm814x and dra62x usb
ARM: OMAP2+: Add mmc hwmod entries for dm814x
ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx
ARM: OMAP2+: Fix SoC detection for dra62x j5-eco
ARM: tango4: Initial platform support
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
ARM: imx: select SRC for i.MX7
ARM: uniphier: select PINCTRL
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: rockchip: enable support for RK3228 SoCs
ARM: rockchip: use const and __initconst for rk3036 smp_operations
ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"A smallish number of general cleanup commits this release cycle. Some
of these are minor tweaks:
- shmobile change of binding for their GIC (using arm,pl390 now)
- ARCH_RENESAS introduction
- Misc other renesas updates
There's also a couple of treewide commits from Masahiro Yamada
cleaning up const/__initconst for SMP operation structs and a switch
to using "depends on" instead of if-constructs on most of the Kconfig
platform targets"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
staging: board: armadillo800eva: Use "arm,pl390"
staging: board: kzm9d: Use "arm,pl390"
ARM: shmobile: r8a7778 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: emev2 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r8a7740 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r7s72100 dtsi: Use "arm,pl390" for GIC
ARM: use "depends on" for SoC configs instead of "if" after prompt
ARM/clocksource: use automatic DT probing for ux500 PRCMU
ARM: use const and __initconst for smp_operations
ARM: hisi: do not export smp_operations structures
ARM: mvebu: remove unused mach/gpio.h
ARM: shmobile: Remove legacy mach/irqs.h
ARM: shmobile: Introduce ARCH_RENESAS
MAINTAINERS: Remove link to oss.renesas.com which is closed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures.
This also adds stricter type checking for callers of do_div, which has
uncovered a number of bugs in existing code, and fixes up the ones we
have found"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ARM: asm/div64.h: adjust to generic codde
__div64_32(): make it overridable at compile time
__div64_const32(): abstract out the actual 128-bit cross product code
do_div(): generic optimization for constant divisor on 32-bit machines
div64.h: optimize do_div() for power-of-two constant divisors
mtd/sm_ftl.c: fix wrong do_div() usage
drm/mgag200/mgag200_mode.c: fix wrong do_div() usage
hid-sensor-hub.c: fix wrong do_div() usage
ti/fapll: fix wrong do_div() usage
ti/clkt_dpll: fix wrong do_div() usage
tegra/clk-divider: fix wrong do_div() usage
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
nouveau/nvkm/subdev/clk/gk20a.c: fix wrong do_div() usage
|
|
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* pm-core:
driver core: Avoid NULL pointer dereferences in device_is_bound()
platform: Do not detach from PM domains on shutdown
USB / PM: Allow USB devices to remain runtime-suspended when sleeping
PM / sleep: Go direct_complete if driver has no callbacks
PM / Domains: add setter for dev.pm_domain
device core: add device_is_bound()
|
|
Pull virtio barrier rework+fixes from Michael Tsirkin:
"This adds a new kind of barrier, and reworks virtio and xen to use it.
Plus some fixes here and there"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (44 commits)
checkpatch: add virt barriers
checkpatch: check for __smp outside barrier.h
checkpatch.pl: add missing memory barriers
virtio: make find_vqs() checkpatch.pl-friendly
virtio_balloon: fix race between migration and ballooning
virtio_balloon: fix race by fill and leak
s390: more efficient smp barriers
s390: use generic memory barriers
xen/events: use virt_xxx barriers
xen/io: use virt_xxx barriers
xenbus: use virt_xxx barriers
virtio_ring: use virt_store_mb
sh: move xchg_cmpxchg to a header by itself
sh: support 1 and 2 byte xchg
virtio_ring: update weak barriers to use virt_xxx
Revert "virtio_ring: Update weak barriers to use dma_wmb/rmb"
asm-generic: implement virt_xxx memory barriers
x86: define __smp_xxx
xtensa: define __smp_xxx
tile: define __smp_xxx
...
|
