| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"For catching up the remaining stuff for 6.17: only small updates and
the rest are mostly small fixes.
- Fixes in HD-audio codec driver Kconfig, so that configurations can
be more easily/safely carried between different versions
- Fixes in ASoC SDCA, FSL xcvr, AW88399
- ASoC IMX WM8524 support
- HD-audio and USB-audio quirks and fixes
- A minor selftest fix"
* tag 'sound-6.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: usb: scarlett2: Fix missing NULL check
mips: Update HD-audio configs again
LoongArch: Update HD-audio codec configs
arm: Update HD-audio configs again
selftests: ALSA: fix memory leak in utimer test
ALSA: usb-audio: Add DSD support for Comtrue USB Audio device
ALSA: hda/hdmi: Enable drivers as default
ALSA: hda/cirrus: Enable drivers as default
ALSA: hda/realtek: Enable drivers as default
ALSA: hda/realtek - Fix mute LED for HP Victus 16-d1xxx (MB 8A26)
ALSA: hda/realtek - Fix mute LED for HP Victus 16-s0xxx
ALSA: hda: Fix the wrong register was used for DVC of TAS2770
ALSA: scarlett2: Add retry on -EPROTO from scarlett2_usb_tx()
ALSA: hda/realtek - Fix mute LED for HP Victus 16-r1xxx
ASoC: codecs: Add acpi_match_table for aw88399 driver
ASoC: dt-bindings: atmel,at91-ssc: add microchip,sam9x7-ssc
ASoC: imx-card: Add WM8524 support
ASoC: fsl_xcvr: get channel status data with firmware exists
ASoC: fsl_xcvr: get channel status data when PHY is not exists
ASoC: SDCA: Add support for -cn- value properties
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"As usual, many cleanups. The below blurbiage describes 42 patchsets.
21 of those are partially or fully cleanup work. "cleans up",
"cleanup", "maintainability", "rationalizes", etc.
I never knew the MM code was so dirty.
"mm: ksm: prevent KSM from breaking merging of new VMAs" (Lorenzo Stoakes)
addresses an issue with KSM's PR_SET_MEMORY_MERGE mode: newly
mapped VMAs were not eligible for merging with existing adjacent
VMAs.
"mm/damon: introduce DAMON_STAT for simple and practical access monitoring" (SeongJae Park)
adds a new kernel module which simplifies the setup and usage of
DAMON in production environments.
"stop passing a writeback_control to swap/shmem writeout" (Christoph Hellwig)
is a cleanup to the writeback code which removes a couple of
pointers from struct writeback_control.
"drivers/base/node.c: optimization and cleanups" (Donet Tom)
contains largely uncorrelated cleanups to the NUMA node setup and
management code.
"mm: userfaultfd: assorted fixes and cleanups" (Tal Zussman)
does some maintenance work on the userfaultfd code.
"Readahead tweaks for larger folios" (Ryan Roberts)
implements some tuneups for pagecache readahead when it is reading
into order>0 folios.
"selftests/mm: Tweaks to the cow test" (Mark Brown)
provides some cleanups and consistency improvements to the
selftests code.
"Optimize mremap() for large folios" (Dev Jain)
does that. A 37% reduction in execution time was measured in a
memset+mremap+munmap microbenchmark.
"Remove zero_user()" (Matthew Wilcox)
expunges zero_user() in favor of the more modern memzero_page().
"mm/huge_memory: vmf_insert_folio_*() and vmf_insert_pfn_pud() fixes" (David Hildenbrand)
addresses some warts which David noticed in the huge page code.
These were not known to be causing any issues at this time.
"mm/damon: use alloc_migrate_target() for DAMOS_MIGRATE_{HOT,COLD" (SeongJae Park)
provides some cleanup and consolidation work in DAMON.
"use vm_flags_t consistently" (Lorenzo Stoakes)
uses vm_flags_t in places where we were inappropriately using other
types.
"mm/memfd: Reserve hugetlb folios before allocation" (Vivek Kasireddy)
increases the reliability of large page allocation in the memfd
code.
"mm: Remove pXX_devmap page table bit and pfn_t type" (Alistair Popple)
removes several now-unneeded PFN_* flags.
"mm/damon: decouple sysfs from core" (SeongJae Park)
implememnts some cleanup and maintainability work in the DAMON
sysfs layer.
"madvise cleanup" (Lorenzo Stoakes)
does quite a lot of cleanup/maintenance work in the madvise() code.
"madvise anon_name cleanups" (Vlastimil Babka)
provides additional cleanups on top or Lorenzo's effort.
"Implement numa node notifier" (Oscar Salvador)
creates a standalone notifier for NUMA node memory state changes.
Previously these were lumped under the more general memory
on/offline notifier.
"Make MIGRATE_ISOLATE a standalone bit" (Zi Yan)
cleans up the pageblock isolation code and fixes a potential issue
which doesn't seem to cause any problems in practice.
"selftests/damon: add python and drgn based DAMON sysfs functionality tests" (SeongJae Park)
adds additional drgn- and python-based DAMON selftests which are
more comprehensive than the existing selftest suite.
"Misc rework on hugetlb faulting path" (Oscar Salvador)
fixes a rather obscure deadlock in the hugetlb fault code and
follows that fix with a series of cleanups.
"cma: factor out allocation logic from __cma_declare_contiguous_nid" (Mike Rapoport)
rationalizes and cleans up the highmem-specific code in the CMA
allocator.
"mm/migration: rework movable_ops page migration (part 1)" (David Hildenbrand)
provides cleanups and future-preparedness to the migration code.
"mm/damon: add trace events for auto-tuned monitoring intervals and DAMOS quota" (SeongJae Park)
adds some tracepoints to some DAMON auto-tuning code.
"mm/damon: fix misc bugs in DAMON modules" (SeongJae Park)
does that.
"mm/damon: misc cleanups" (SeongJae Park)
also does what it claims.
"mm: folio_pte_batch() improvements" (David Hildenbrand)
cleans up the large folio PTE batching code.
"mm/damon/vaddr: Allow interleaving in migrate_{hot,cold} actions" (SeongJae Park)
facilitates dynamic alteration of DAMON's inter-node allocation
policy.
"Remove unmap_and_put_page()" (Vishal Moola)
provides a couple of page->folio conversions.
"mm: per-node proactive reclaim" (Davidlohr Bueso)
implements a per-node control of proactive reclaim - beyond the
current memcg-based implementation.
"mm/damon: remove damon_callback" (SeongJae Park)
replaces the damon_callback interface with a more general and
powerful damon_call()+damos_walk() interface.
"mm/mremap: permit mremap() move of multiple VMAs" (Lorenzo Stoakes)
implements a number of mremap cleanups (of course) in preparation
for adding new mremap() functionality: newly permit the remapping
of multiple VMAs when the user is specifying MREMAP_FIXED. It still
excludes some specialized situations where this cannot be performed
reliably.
"drop hugetlb_free_pgd_range()" (Anthony Yznaga)
switches some sparc hugetlb code over to the generic version and
removes the thus-unneeded hugetlb_free_pgd_range().
"mm/damon/sysfs: support periodic and automated stats update" (SeongJae Park)
augments the present userspace-requested update of DAMON sysfs
monitoring files. Automatic update is now provided, along with a
tunable to control the update interval.
"Some randome fixes and cleanups to swapfile" (Kemeng Shi)
does what is claims.
"mm: introduce snapshot_page" (Luiz Capitulino and David Hildenbrand)
provides (and uses) a means by which debug-style functions can grab
a copy of a pageframe and inspect it locklessly without tripping
over the races inherent in operating on the live pageframe
directly.
"use per-vma locks for /proc/pid/maps reads" (Suren Baghdasaryan)
addresses the large contention issues which can be triggered by
reads from that procfs file. Latencies are reduced by more than
half in some situations. The series also introduces several new
selftests for the /proc/pid/maps interface.
"__folio_split() clean up" (Zi Yan)
cleans up __folio_split()!
"Optimize mprotect() for large folios" (Dev Jain)
provides some quite large (>3x) speedups to mprotect() when dealing
with large folios.
"selftests/mm: reuse FORCE_READ to replace "asm volatile("" : "+r" (XXX));" and some cleanup" (wang lian)
does some cleanup work in the selftests code.
"tools/testing: expand mremap testing" (Lorenzo Stoakes)
extends the mremap() selftest in several ways, including adding
more checking of Lorenzo's recently added "permit mremap() move of
multiple VMAs" feature.
"selftests/damon/sysfs.py: test all parameters" (SeongJae Park)
extends the DAMON sysfs interface selftest so that it tests all
possible user-requested parameters. Rather than the present minimal
subset"
* tag 'mm-stable-2025-07-30-15-25' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (370 commits)
MAINTAINERS: add missing headers to mempory policy & migration section
MAINTAINERS: add missing file to cgroup section
MAINTAINERS: add MM MISC section, add missing files to MISC and CORE
MAINTAINERS: add missing zsmalloc file
MAINTAINERS: add missing files to page alloc section
MAINTAINERS: add missing shrinker files
MAINTAINERS: move memremap.[ch] to hotplug section
MAINTAINERS: add missing mm_slot.h file THP section
MAINTAINERS: add missing interval_tree.c to memory mapping section
MAINTAINERS: add missing percpu-internal.h file to per-cpu section
mm/page_alloc: remove trace_mm_alloc_contig_migrate_range_info()
selftests/damon: introduce _common.sh to host shared function
selftests/damon/sysfs.py: test runtime reduction of DAMON parameters
selftests/damon/sysfs.py: test non-default parameters runtime commit
selftests/damon/sysfs.py: generalize DAMON context commit assertion
selftests/damon/sysfs.py: generalize monitoring attributes commit assertion
selftests/damon/sysfs.py: generalize DAMOS schemes commit assertion
selftests/damon/sysfs.py: test DAMOS filters commitment
selftests/damon/sysfs.py: generalize DAMOS scheme commit assertion
selftests/damon/sysfs.py: test DAMOS destinations commitment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Allow hash drivers without fallbacks (e.g., hardware key)
Algorithms:
- Add hmac hardware key support (phmac) on s390
- Re-enable sha384 in FIPS mode
- Disable sha1 in FIPS mode
- Convert zstd to acomp
Drivers:
- Lower priority of qat skcipher and aead
- Convert aspeed to partial block API
- Add iMX8QXP support in caam
- Add rate limiting support for GEN6 devices in qat
- Enable telemetry for GEN6 devices in qat
- Implement full backlog mode for hisilicon/sec2"
* tag 'v6.17-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
crypto: keembay - Use min() to simplify ocs_create_linked_list_from_sg()
crypto: hisilicon/hpre - fix dma unmap sequence
crypto: qat - make adf_dev_autoreset() static
crypto: ccp - reduce stack usage in ccp_run_aes_gcm_cmd
crypto: qat - refactor ring-related debug functions
crypto: qat - fix seq_file position update in adf_ring_next()
crypto: qat - fix DMA direction for compression on GEN2 devices
crypto: jitter - replace ARRAY_SIZE definition with header include
crypto: engine - remove {prepare,unprepare}_crypt_hardware callbacks
crypto: engine - remove request batching support
crypto: qat - flush misc workqueue during device shutdown
crypto: qat - enable rate limiting feature for GEN6 devices
crypto: qat - add compression slice count for rate limiting
crypto: qat - add get_svc_slice_cnt() in device data structure
crypto: qat - add adf_rl_get_num_svc_aes() in rate limiting
crypto: qat - relocate service related functions
crypto: qat - consolidate service enums
crypto: qat - add decompression service for rate limiting
crypto: qat - validate service in rate limiting sysfs api
crypto: hisilicon/sec2 - implement full backlog mode for sec
...
|
|
The Realtek and HDMI HD-audio codec configs have been slightly updated
again since the previous change. Follow the new kconfig changes for
multi_v7_defconfig and tegra_defconfig, and add a few other configs
for HDMI codecs, too.
Fixes: 1d8dd982c409 ("ALSA: hda/realtek: Enable drivers as default")
Fixes: 81231ad173d8 ("ALSA: hda/hdmi: Enable drivers as default")
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250731091109.16901-2-tiwai@suse.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracepoint cleanup from Steven Rostedt:
"Remove or hide unused tracepoints
Tracepoints take up memory (around 5K per tracepoint) even when they
are unused. Changes are being made to detect when a tracepoint is
defined but unused and a warning is shown at build. But those changes
are not yet ready for inclusion.
- Fix some of the unused tracepoints that it detected
Some tracepoints were removed and others were hidden by config
settings to match the config settings of where they are
instantiated. Some tracepoints were moved into architecture
specific code as only one architecture used them.
- Call the ftrace_test_filter tracepoint in an unreachable if
statement
The ftrace_test_filter tracepoint which is defined when ftrace
selftests are configured and is used to test the filter logic, but
the tracepoint is not actually called. It is put into an if
statement to not have it get compiled out, but also not warn for
not being used"
* tag 'trace-unused-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: sched: Hide numa events under CONFIG_NUMA_BALANCING
powerpc/thp: tracing: Hide hugepage events under CONFIG_PPC_BOOK3S_64
tracing: Call trace_ftrace_test_filter() for the event
tracing: arm: arm64: Hide trace events ipi_raise, ipi_entry and ipi_exit
binder: Remove unused binder lock events
PM: tracing: Hide power_domain_target event under ARCH_OMAP2PLUS
PM: tracing: Hide device_pm_callback events under PM_SLEEP
PM: tracing: Hide psci_domain_idle events under ARM_PSCI_CPUIDLE
PM: cpufreq: powernv/tracing: Move powernv_throttle trace event
alarmtimer: Hide alarmtimer_suspend event when RTC_CLASS is not configured
tracing, AER: Hide PCIe AER event when PCIEAER is not configured
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull ftrace updates from Steven Rostedt:
- Keep track of when fgraph_ops are registered or not
Keep accounting of when fgraph_ops are registered as if a fgraph_ops
is registered twice it can mess up the accounting and it will not
work as expected later. Trigger a warning if something registers it
twice as to catch bugs before they are found by things just not
working as expected.
- Make DYNAMIC_FTRACE always enabled for architectures that support it
As static ftrace (where all functions are always traced) is very
expensive and only exists to help architectures support ftrace, do
not make it an option. As soon as an architecture supports
DYNAMIC_FTRACE make it use it. This simplifies the code.
- Remove redundant config HAVE_FTRACE_MCOUNT_RECORD
The CONFIG_HAVE_FTRACE_MCOUNT was added to help simplify the
DYNAMIC_FTRACE work, but now every architecture that implements
DYNAMIC_FTRACE also has HAVE_FTRACE_MCOUNT set too, making it
redundant with the HAVE_DYNAMIC_FTRACE.
- Make pid_ptr string size match the comment
In print_graph_proc() the pid_ptr string is of size 11, but the
comment says /* sign + log10(MAX_INT) + '\0' */ which is actually 12.
* tag 'ftrace-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Remove redundant config HAVE_FTRACE_MCOUNT_RECORD
ftrace: Make DYNAMIC_FTRACE always enabled for architectures that support it
fgraph: Keep track of when fgraph_ops are registered or not
fgraph: Make pid_str size match the comment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC code updates from Arnd Bergmann:
"Another small set of code changes for the 32-bit Arm platforms, and a
trivial update to the Kconfig entry for the arm64 TI K3 chip.
Andrew Davis cleans up the system reset handling, which touches a
couple of platforms.
The mediatek platform needs some code changes to support
multiprocessing in the newly added support for the old mt6572 chip"
* tag 'soc-arm-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: sa110/gpio: convert set_multiple() to returning an integer
ARM: rockchip: fix kernel hang during smp initialization
ARM: mediatek: add MT6572 smp bring up code
ARM: mediatek: add board_dt_compat entry for the MT6572 SoC
ARM: tegra: Use I/O memcpy to write to IRAM
arm: orion: use string choices helper
ARM: Switch to new sys-off handler API
arm64: Kconfig.platforms: remove useless select for ARCH_K3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC defconfig updates from Arnd Bergmann:
"As usual, more drivers get enabled in the defconfigs, to support newly
added hardware drivers.
There is one change for Tegra that modifies the Kconfig file at the
same time, and the NXP arm32 defconfigs get a refresh"
* tag 'soc-defconfig-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
arm: multi_v7_defconfig: Enable TPS65219 regulator
arm: omap2plus_defconfig: Enable TPS65219 regulator
arm64: defconfig: Enable Tegra241 and Tegra264
riscv: defconfig: spacemit: enable sdhci driver for K1 SoC
riscv: defconfig: Enable PWM support for SpacemiT K1 SoC
riscv: defconfig: Remove CONFIG_SND_SOC_STARFIVE=m
arm64: defconfig: Enable Tegra HSP and BPMP
ARM: imx_v6_v7_defconfig: select CONFIG_USB_HSIC_USB3503
ARM: imx_v6_v7_defconfig: select CONFIG_INPUT_PWM_BEEPER
ARM: imx_v6_v7_defconfig: cleanup with savedefconfig
ARM: mxs_defconfig: select new drivers used by imx28-amarula-rmm
ARM: mxs_defconfig: Cleanup mxs_defconfig
arm64: defconfig: enable further Rockchip platform drivers
arm64: defconfig: enable Samsung PMIC over ACPM
arm64: defconfig: enable Maxim max77759 driver
ARM: configs: sama5_defconfig: Select CONFIG_WILC1000_SDIO
ARM: shmobile: defconfig: Refresh for v6.16-rc2
arm64: defconfig: Enable RZ/V2H(P) USB2 PHY controller reset driver
arm64: defconfig: add S32G RTC module support
arm64: defconfig: Drop unneeded unselectable sound drivers
...
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There are a few new variants of existing chips:
- mt6572 is an older mobile phone chip from mediatek that was
extremely popular a decade ago but never got upstreamed until now
- exynos2200 is a recent high-end mobile phone chip used in a few
Samsung phones like the Galaxy S22
- Renesas R-Car V4M-7 (R8A779H2) is an updated version of R-Car V4M
(R8A779H0) and used in automotive applications
- Tegra264 is a new chip from NVIDIA, but support is fairly minimal
for now, and not much information is public about it
There are five more chips in a separate branch, as those are new chip
families that I merged along with the necessary infrastructure.
New board support is not that exciting, with a total of 33 newly added
machines here:
- Evaluation platforms for the chips above, plus TI am62d2 and Sophgo
sg2042
- Six 32-bit industrial boards based on stm32, imx6 and am33 chips,
plus eight 64-bit rockchips rk33xx/rk35xx, am62d2, t527, imx8 and
imx95
- Two newly added ASPEED BMC based motherboards, and one that got
removed
- Phones and Tablets based on 32-bit mt6572, tegra30 and 64-bit
msm8976 SoCs
- Three Laptops based on Mediatek mt8186 and Qualcomm Snapdragon X1
- A set-top box based on Amlogic meson-gxm
Updates for existing machines are spread over all the above families.
One notable change here is support for the RP1 I/O chip used in
Raspberry Pi 5"
* tag 'soc-dt-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (606 commits)
riscv: dts: sophgo: fix mdio node name for CV180X
riscv: dts: sophgo: sophgo-srd3-10: reserve uart0 device
riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree
riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree
dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings
riscv: dts: sophgo: add ethernet GMAC device for sg2042
riscv: dts: sophgo: Enable ethernet device for Huashan Pi
riscv: dts: sophgo: Add mdio multiplexer device for cv18xx
riscv: dts: sophgo: Add ethernet device for cv18xx
riscv: dts: sophgo: sg2044: add pmu configuration
riscv: dts: sophgo: sg2044: add ziccrse extension
riscv: dts: sophgo: add zfh for sg2042
riscv: dts: sophgo: add ziccrse for sg2042
riscv: dts: sophgo: Add xtheadvector to the sg2042 devicetree
riscv: dts: sophgo: sg2044: add PCIe device support for SG2044
riscv: dts: sophgo: sg2044: add MSI device support for SG2044
riscv: dts: sophgo: add reset configuration for Sophgo CV1800 series SoC
riscv: dts: sophgo: add reset generator for Sophgo CV1800 series SoC
dt-bindings: soc: sophgo: Move SoCs/boards from riscv into soc, add SG2000
riscv: dts: sophgo: sg2044: Add missing riscv,cbop-block-size property
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There's one new driver (Apple SMC) and extensions to existing drivers
for supporting new HW models. A lot of different impovements across
drivers and in core GPIO code. Details on that are in the signed tag
as usual.
We managed to remove some of the legacy APIs. Arnd Bergmann started to
work on making the legacy bits optional so that we may compile them
only for older platforms that still really need them.
Rob Herring has done a lot of work to convert legacy .txt dt-bindings
for GPIO controllers to YAML. There are only a few left now in the
GPIO tree.
A big part of the commits in this PR concern the conversion of GPIO
drivers to using the new line value setter callbacks. This conversion
is now complete treewide (unless I've missed something) and once all
the changes from different trees land in mainline, I'll send you
another PR containing a commit dropping the legacy callbacks from the
tree.
As the quest to pay back technical dept never really ends, we're
starting another set of interface conversions, this time it's about
moving fields specific to only a handful of drivers using the
gpio-mmio helper out of the core gpio_chip structure that every
controller implements and uses. This cycle we introduce a new set of
APIs and convert a few drivers under drivers/gpio/, next cycle we'll
convert remaining modules treewide (in gpio, pinctrl and mfd trees)
and finally remove the old interfaces and move the gpio-mmio fields
into their own structure wrapping gpio_chip.
One last change I should mention here is the rework of the sysfs
interface. In 2016, we introduced the GPIO character device as the
preferred alternative to the sysfs class under /sys/class/gpio. While
it has seen a wide adoption with the help of its user-space
counterpart - libgpiod - there are still users who prefer the
simplicity of sysfs.
As far as the GPIO subsystem is concerned, the problem is not the
existince of the GPIO class as such but rather the fact that it
exposes the global GPIO numbers to the user-space, stopping us from
ever being able to remove the numberspace from the kernel. To that
end, this release we introduced a parallel, limited sysfs interface
that doesn't expose these numbers and only implements a subset of
features that are relevant to the existing users. This is a result of
several discussions over the course of last year and should allow us
to remove the legacy part some time in the future.
Summary:
GPIOLIB core:
- introduce a parallel, limited sysfs user ABI that doesn't expose
the global GPIO numbers to user-space while maintaining backward
compatibility with the end goal of it completely replacing the
existing interface, allowing us to remove it
- remove the legacy devm_gpio_request() routine which has no more
users
- start the process of allowing to compile-out the legacy parts of
the GPIO core for users who don't need it by introducing a new
Kconfig option: GPIOLIB_LEGACY
- don't use global GPIO numbers in debugfs output from the core code
(drivers still do it, the work is ongoing)
- start the process of moving the fields specific to the gpio-mmio
helper out of the core struct gpio_chip into their own structure
that wraps it: create a new header with modern interfaces and
convert several drivers to using it
- remove the platform data structure associated with the gpio-mmio
helper from the kernel after having converted all remaining users
to generic device properties
- remove legacy struct gpio definition as it has no more users
New drivers:
- add the GPIO driver for the Apple System Management Controller
Driver improvements:
- add support for new models to gpio-adp5585, gpio-tps65219 and
gpio-pca953x
- extend the interrupt support in gpio-loongson-64bit
- allow to mark the simulated GPIO lines as invalid in gpio-sim
- convert all remaining GPIO drivers to using the new GPIO value
setter callbacks
- convert gpio-rcar to using simple device power management ops
callbacks
- don't check if current direction of a line is output before setting
the value in gpio-pisosr and ti-fpc202: the GPIO core already
handles that
- also drop unneeded GPIO range checks in drivers, the core already
makes sure we're within bounds when calling driver callbacks
- use dev_fwnode() where applicable across GPIO drivers
- set line value in gpio-zynqmp-modepin and gpio-twl6040 when the
user wants to change direction of the pin to output even though
these drivers don't need to do anything else to actually set the
direction, otherwise a call like gpiod_direction_output(d, 1) will
not result in the line driver high
- remove the reduntant call to pm_runtime_mark_last_busy() from
gpio-arizona
- use lock guards in gpio-cadence and gpio-mxc
- check the return values of regmap functions in gpio-wcd934x and
gpio-tps65912
- use better regmap interfaces in gpio-wcove and gpio-pca953x
- remove dummy GPIO chip callbacks from several drivers in cases
where the GPIO core can already handle their absence
- allow building gpio-palmas as a module
Fixes:
- use correct bit widths (according to the documentation) in
gpio-virtio
Device-tree bindings:
- convert several of the legacy .txt documents for many different
devices to YAML, improving automatic validation
- create a "trivial" GPIO DT schema that covers a wide range of
simple hardware that share a set of basic GPIO properties
- document new HW: Apple MAC SMC GPIO block and adp5589 I/O expander
- document a new model for pca95xx
- add and/or remove properties in YAML documents for gpio-rockchip,
fsl,qoriq-gpio, arm,pl061 and gpio-xilinx
Misc:
- some minor refactoring in several places, adding/removing forward
declarations, moving defines to better places, constify the
arguments in some functions, remove duplicate includes, etc.
- documentation updates"
* tag 'gpio-updates-for-v6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (202 commits)
MIPS: alchemy: gpio: use new GPIO line value setter callbacks for the remaining chips
gpiolib: enable CONFIG_GPIOLIB_LEGACY even for !GPIOLIB
gpio: virtio: Fix config space reading.
gpiolib: make legacy interfaces optional
dt-bindings: gpio: rockchip: Allow use of a power-domain
gpiolib: of: add forward declaration for struct device_node
power: reset: macsmc-reboot: Add driver for rebooting via Apple SMC
gpio: Add new gpio-macsmc driver for Apple Macs
mfd: Add Apple Silicon System Management Controller
soc: apple: rtkit: Make shmem_destroy optional
dt-bindings: mfd: Add Apple Mac System Management Controller
dt-bindings: power: reboot: Add Apple Mac SMC Reboot Controller
dt-bindings: gpio: Add Apple Mac SMC GPIO block
gpio: cadence: Remove duplicated include in gpio-cadence.c
gpio: tps65219: Add support for TI TPS65214 PMIC
gpio: tps65219: Update _IDX & _OFFSET macro prefix
gpio: sysfs: Fix an end of loop test in gpiod_unexport()
dt-bindings: gpio: Convert qca,ar7100-gpio to DT schema
dt-bindings: gpio: Convert maxim,max3191x to DT schema
dt-bindings: gpio: fsl,qoriq-gpio: Add missing mpc8xxx compatibles
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This includes lots of file shuffling due to HD-audio code
reorganization and many trivial changes, but otherwise there shouldn't
be much surprise from the functionality POV. The PR includes the PM
changes as prerequisite, too. Some highlights below:
Core:
- Performance optimizations in PCM core code
- Refactoring of ASoC Kconfig menus to be hopefully more consistant
and easier to navigate.
- Refactoring of ASoC DAPM code, mainly hiding functionality that
doesn't need to be exposed to drivers
HD-audio reorganization:
- All code are moved under sound/hda with a bit more understandable
tree structure, as well as file renames
- The huge Realtek driver code is split to several parts, a common
helper module with driver modules per probe entry
- HDMI and Cirrus codec drivers also split
ASoC:
- Further work on the generic handling for SoundWire SDCA devices
- Support for AMD ACP7.2 and SoundWire on ACP 7.1, Fairphone 4 & 5,
various Intel systems, Qualcomm QCS8275, Richtek RTQ9124 and TI
TAS5753
HD-audio and USB-audio:
- TAS2781 driver cleanup and TAS2770 support
- EQ enablement in CA0132 driver
- USB audio quirk code cleanups
Others:
- Cleanups of PM autosuspend call patterns with the update from the
PM tree
- Lots of strcpy() -> strscpy() conversions for fixed size arrays"
* tag 'sound-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (385 commits)
ALSA: hda: Add TAS2770 support
ASoC: qcom: sm8250: Add Fairphone 4 soundcard compatible
ASoC: dt-bindings: qcom,sm8250: Add Fairphone 4 sound card
ASoC: dt-bindings: qcom,q6afe: Document q6usb subnode
ASoC: SDCA: Fix implicit cast from le16
ASoC: SDCA: Shrink detected_mode_handler() stack frame
ASoC: SDCA: Check devm_mutex_init() return value
ASoC: SDCA: add route by the number of input pins in MU entity
ALSA: hda/realtek: Add support for ASUS Commercial laptops using CS35L41 HDA
ASoC: Intel: sof_rt5682: Add HDMI-In capture with rt5682 support for PTL.
ASoC: codec: tlv320aic32x4: Fix reset GPIO check
ASoC: dt-bindings: qcom,lpass-va-macro: Define clock-names in top-level
ASoC: SDCA: Add hw_params() helper function
ASoC: SDCA: Add a helper to get the SoundWire port number
ASoC: SDCA: Add helper to add DAI constraints
ASoC: soc-dai: Add private data to snd_soc_dai
ASoC: SDCA: Move SDCA search functions and export
ASoC: SDCA: Remove overly chatty input pin list warning
ASoC: SDCA: Allow read-only controls to be deferrable
ASoC: SDCA: Update memory allocations to zero initialise
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library updates from Eric Biggers:
"This is the main crypto library pull request for 6.17. The main focus
this cycle is on reorganizing the SHA-1 and SHA-2 code, providing
high-quality library APIs for SHA-1 and SHA-2 including HMAC support,
and establishing conventions for lib/crypto/ going forward:
- Migrate the SHA-1 and SHA-512 code (and also SHA-384 which shares
most of the SHA-512 code) into lib/crypto/. This includes both the
generic and architecture-optimized code. Greatly simplify how the
architecture-optimized code is integrated. Add an easy-to-use
library API for each SHA variant, including HMAC support. Finally,
reimplement the crypto_shash support on top of the library API.
- Apply the same reorganization to the SHA-256 code (and also SHA-224
which shares most of the SHA-256 code). This is a somewhat smaller
change, due to my earlier work on SHA-256. But this brings in all
the same additional improvements that I made for SHA-1 and SHA-512.
There are also some smaller changes:
- Move the architecture-optimized ChaCha, Poly1305, and BLAKE2s code
from arch/$(SRCARCH)/lib/crypto/ to lib/crypto/$(SRCARCH)/. For
these algorithms it's just a move, not a full reorganization yet.
- Fix the MIPS chacha-core.S to build with the clang assembler.
- Fix the Poly1305 functions to work in all contexts.
- Fix a performance regression in the x86_64 Poly1305 code.
- Clean up the x86_64 SHA-NI optimized SHA-1 assembly code.
Note that since the new organization of the SHA code is much simpler,
the diffstat of this pull request is negative, despite the addition of
new fully-documented library APIs for multiple SHA and HMAC-SHA
variants.
These APIs will allow further simplifications across the kernel as
users start using them instead of the old-school crypto API. (I've
already written a lot of such conversion patches, removing over 1000
more lines of code. But most of those will target 6.18 or later)"
* tag 'libcrypto-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (67 commits)
lib/crypto: arm64/sha512-ce: Drop compatibility macros for older binutils
lib/crypto: x86/sha1-ni: Convert to use rounds macros
lib/crypto: x86/sha1-ni: Minor optimizations and cleanup
crypto: sha1 - Remove sha1_base.h
lib/crypto: x86/sha1: Migrate optimized code into library
lib/crypto: sparc/sha1: Migrate optimized code into library
lib/crypto: s390/sha1: Migrate optimized code into library
lib/crypto: powerpc/sha1: Migrate optimized code into library
lib/crypto: mips/sha1: Migrate optimized code into library
lib/crypto: arm64/sha1: Migrate optimized code into library
lib/crypto: arm/sha1: Migrate optimized code into library
crypto: sha1 - Use same state format as legacy drivers
crypto: sha1 - Wrap library and add HMAC support
lib/crypto: sha1: Add HMAC support
lib/crypto: sha1: Add SHA-1 library functions
lib/crypto: sha1: Rename sha1_init() to sha1_init_raw()
crypto: x86/sha1 - Rename conflicting symbol
lib/crypto: sha2: Add hmac_sha*_init_usingrawkey()
lib/crypto: arm/poly1305: Remove unneeded empty weak function
lib/crypto: x86/poly1305: Fix performance regression on short messages
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull CRC updates from Eric Biggers:
- Reorganize the architecture-optimized CRC code
It now lives in lib/crc/$(SRCARCH)/ rather than arch/$(SRCARCH)/lib/,
and it is no longer artificially split into separate generic and arch
modules. This allows better inlining and dead code elimination
The generic CRC code is also no longer exported, simplifying the API.
(This mirrors the similar changes to SHA-1 and SHA-2 in lib/crypto/,
which can be found in the "Crypto library updates" pull request)
- Improve crc32c() performance on newer x86_64 CPUs on long messages by
enabling the VPCLMULQDQ optimized code
- Simplify the crypto_shash wrappers for crc32_le() and crc32c()
Register just one shash algorithm for each that uses the (fully
optimized) library functions, instead of unnecessarily providing
direct access to the generic CRC code
- Remove unused and obsolete drivers for hardware CRC engines
- Remove CRC-32 combination functions that are no longer used
- Add kerneldoc for crc32_le(), crc32_be(), and crc32c()
- Convert the crc32() macro to an inline function
* tag 'crc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (26 commits)
lib/crc: x86/crc32c: Enable VPCLMULQDQ optimization where beneficial
lib/crc: x86: Reorganize crc-pclmul static_call initialization
lib/crc: crc64: Add include/linux/crc64.h to kernel-api.rst
lib/crc: crc32: Change crc32() from macro to inline function and remove cast
nvmem: layouts: Switch from crc32() to crc32_le()
lib/crc: crc32: Document crc32_le(), crc32_be(), and crc32c()
lib/crc: Explicitly include <linux/export.h>
lib/crc: Remove ARCH_HAS_* kconfig symbols
lib/crc: x86: Migrate optimized CRC code into lib/crc/
lib/crc: sparc: Migrate optimized CRC code into lib/crc/
lib/crc: s390: Migrate optimized CRC code into lib/crc/
lib/crc: riscv: Migrate optimized CRC code into lib/crc/
lib/crc: powerpc: Migrate optimized CRC code into lib/crc/
lib/crc: mips: Migrate optimized CRC code into lib/crc/
lib/crc: loongarch: Migrate optimized CRC code into lib/crc/
lib/crc: arm64: Migrate optimized CRC code into lib/crc/
lib/crc: arm: Migrate optimized CRC code into lib/crc/
lib/crc: Prepare for arch-optimized code in subdirs of lib/crc/
lib/crc: Move files into lib/crc/
lib/crc32: Remove unused combination support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
- Introduce and start using TRAILING_OVERLAP() helper for fixing
embedded flex array instances (Gustavo A. R. Silva)
- mux: Convert mux_control_ops to a flex array member in mux_chip
(Thorsten Blum)
- string: Group str_has_prefix() and strstarts() (Andy Shevchenko)
- Remove KCOV instrumentation from __init and __head (Ritesh Harjani,
Kees Cook)
- Refactor and rename stackleak feature to support Clang
- Add KUnit test for seq_buf API
- Fix KUnit fortify test under LTO
* tag 'hardening-v6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (22 commits)
sched/task_stack: Add missing const qualifier to end_of_stack()
kstack_erase: Support Clang stack depth tracking
kstack_erase: Add -mgeneral-regs-only to silence Clang warnings
init.h: Disable sanitizer coverage for __init and __head
kstack_erase: Disable kstack_erase for all of arm compressed boot code
x86: Handle KCOV __init vs inline mismatches
arm64: Handle KCOV __init vs inline mismatches
s390: Handle KCOV __init vs inline mismatches
arm: Handle KCOV __init vs inline mismatches
mips: Handle KCOV __init vs inline mismatch
powerpc/mm/book3s64: Move kfence and debug_pagealloc related calls to __init section
configs/hardening: Enable CONFIG_INIT_ON_FREE_DEFAULT_ON
configs/hardening: Enable CONFIG_KSTACK_ERASE
stackleak: Split KSTACK_ERASE_CFLAGS from GCC_PLUGINS_CFLAGS
stackleak: Rename stackleak_track_stack to __sanitizer_cov_stack_depth
stackleak: Rename STACKLEAK to KSTACK_ERASE
seq_buf: Introduce KUnit tests
string: Group str_has_prefix() and strstarts()
kunit/fortify: Add back "volatile" for sizeof() constants
acpi: nfit: intel: avoid multiple -Wflex-array-member-not-at-end warnings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull execve updates from Kees Cook:
- Introduce regular REGSET note macros arch-wide (Dave Martin)
- Remove arbitrary 4K limitation of program header size (Yin Fengwei)
- Reorder function qualifiers for copy_clone_args_from_user() (Dishank Jogi)
* tag 'execve-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (25 commits)
fork: reorder function qualifiers for copy_clone_args_from_user
binfmt_elf: remove the 4k limitation of program header size
binfmt_elf: Warn on missing or suspicious regset note names
xtensa: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
um: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
x86/ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
sparc: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
sh: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
s390/ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
riscv: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
powerpc/ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
parisc: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
openrisc: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
nios2: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
MIPS: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
m68k: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
LoongArch: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
hexagon: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
csky: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
arm64: ptrace: Use USER_REGSET_NOTE_TYPE() to specify regset note names
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull fileattr updates from Christian Brauner:
"This introduces the new file_getattr() and file_setattr() system calls
after lengthy discussions.
Both system calls serve as successors and extensible companions to
the FS_IOC_FSGETXATTR and FS_IOC_FSSETXATTR system calls which have
started to show their age in addition to being named in a way that
makes it easy to conflate them with extended attribute related
operations.
These syscalls allow userspace to set filesystem inode attributes on
special files. One of the usage examples is the XFS quota projects.
XFS has project quotas which could be attached to a directory. All new
inodes in these directories inherit project ID set on parent
directory.
The project is created from userspace by opening and calling
FS_IOC_FSSETXATTR on each inode. This is not possible for special
files such as FIFO, SOCK, BLK etc. Therefore, some inodes are left
with empty project ID. Those inodes then are not shown in the quota
accounting but still exist in the directory. This is not critical but
in the case when special files are created in the directory with
already existing project quota, these new inodes inherit extended
attributes. This creates a mix of special files with and without
attributes. Moreover, special files with attributes don't have a
possibility to become clear or change the attributes. This, in turn,
prevents userspace from re-creating quota project on these existing
files.
In addition, these new system calls allow the implementation of
additional attributes that we couldn't or didn't want to fit into the
legacy ioctls anymore"
* tag 'vfs-6.17-rc1.fileattr' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: tighten a sanity check in file_attr_to_fileattr()
tree-wide: s/struct fileattr/struct file_kattr/g
fs: introduce file_getattr and file_setattr syscalls
fs: prepare for extending file_get/setattr()
fs: make vfs_fileattr_[get|set] return -EOPNOTSUPP
selinux: implement inode_file_[g|s]etattr hooks
lsm: introduce new hooks for setting/getting inode fsxattr
fs: split fileattr related helpers into separate file
|
|
When building with CONFIG_KSTACK_ERASE=y and CONFIG_ARM_ATAG_DTB_COMPAT=y,
the compressed boot environment encounters an undefined symbol error:
ld.lld: error: undefined symbol: __sanitizer_cov_stack_depth
>>> referenced by atags_to_fdt.c:135
This occurs because the compiler instruments the atags_to_fdt() function
with sanitizer coverage calls, but the minimal compressed boot environment
lacks access to sanitizer runtime support.
The compressed boot environment already disables stack protector with
-fno-stack-protector. Similarly disable sanitizer coverage by adding
$(DISABLE_KSTACK_ERASE) to the general compiler flags (and remove it
from the one place it was noticed before), which contains the appropriate
flags to prevent sanitizer instrumentation.
This follows the same pattern used in other early boot contexts where
sanitizer runtime support is unavailable.
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/all/CA+G9fYtBk8qnpWvoaFwymCx5s5i-5KXtPGpmf=_+UKJddCOnLA@mail.gmail.com
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/all/20250726004313.GA3650901@ax162
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few Allwinner clk driver fixes:
- Mark Allwinner A523 MBUS clock as critical to avoid
system stalls
- Fix names of CSI related clocks on Allwinner V3s. This
includes changes to the driver, DT bindings and DT files.
- Fix parents of TCON clock on Allwinner V3s"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: v3s: Fix TCON clock parents
clk: sunxi-ng: v3s: Fix CSI1 MCLK clock name
clk: sunxi-ng: v3s: Fix CSI SCLK clock name
clk: sunxi-ng: a523: Mark MBUS clock as critical
|
|
Pull ARM fixes from Russell King:
- use an absolute path for asm/unified.h in KBUILD_AFLAGS to solve a
regression caused by commit d5c8d6e0fa61 ("kbuild: Update assembler
calls to use proper flags and language target")
- fix dead code elimination binutils version check again
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux:
ARM: 9450/1: Fix allowing linker DCE with binutils < 2.36
ARM: 9448/1: Use an absolute path to unified.h in KBUILD_AFLAGS
|
|
Commit e7607f7d6d81 ("ARM: 9443/1: Require linker to support KEEP within
OVERLAY for DCE") accidentally broke the binutils version restriction
that was added in commit 0d437918fb64 ("ARM: 9414/1: Fix build issue
with LD_DEAD_CODE_DATA_ELIMINATION"), reintroducing the segmentation
fault addressed by that workaround.
Restore the binutils version dependency by using
CONFIG_LD_CAN_USE_KEEP_IN_OVERLAY as an additional condition to ensure
that CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION is only enabled with
binutils >= 2.36 and ld.lld >= 21.0.0.
Closes: https://lore.kernel.org/6739da7d-e555-407a-b5cb-e5681da71056@landley.net/
Closes: https://lore.kernel.org/CAFERDQ0zPoya5ZQfpbeuKVZEo_fKsonLf6tJbp32QnSGAtbi+Q@mail.gmail.com/
Cc: stable@vger.kernel.org
Fixes: e7607f7d6d81 ("ARM: 9443/1: Require linker to support KEEP within OVERLAY for DCE")
Reported-by: Rob Landley <rob@landley.net>
Tested-by: Rob Landley <rob@landley.net>
Reported-by: Martin Wetterwald <martin@wetterwald.eu>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
After commit d5c8d6e0fa61 ("kbuild: Update assembler calls to use proper
flags and language target"), which updated as-instr to use the
'assembler-with-cpp' language option, the Kbuild version of as-instr
always fails internally for arch/arm with
<command-line>: fatal error: asm/unified.h: No such file or directory
compilation terminated.
because '-include' flags are now taken into account by the compiler
driver and as-instr does not have '$(LINUXINCLUDE)', so unified.h is not
found.
This went unnoticed at the time of the Kbuild change because the last
use of as-instr in Kbuild that arch/arm could reach was removed in 5.7
by commit 541ad0150ca4 ("arm: Remove 32bit KVM host support") but a
stable backport of the Kbuild change to before that point exposed this
potential issue if one were to be reintroduced.
Follow the general pattern of '-include' paths throughout the tree and
make unified.h absolute using '$(srctree)' to ensure KBUILD_AFLAGS can
be used independently.
Closes: https://lore.kernel.org/CACo-S-1qbCX4WAVFA63dWfHtrRHZBTyyr2js8Lx=Az03XHTTHg@mail.gmail.com/
Cc: stable@vger.kernel.org
Fixes: d5c8d6e0fa61 ("kbuild: Update assembler calls to use proper flags and language target")
Reported-by: KernelCI bot <bot@kernelci.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The ipi tracepoints are mostly generic, but the tracepoints ipi_raise,
ipi_entry and ipi_exit are only used by arm and arm64. This means these
trace events are wasting memory in all the other architectures that do not
use them.
Add CONFIG_HAVE_EXTRA_IPI_TRACEPOINTS and have arm and arm64 select it to
enable these trace events. The config makes it easy if other architectures
decide to trace these as well.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Valentin Schneider <vschneid@redhat.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/20250722103714.64eba013@gandalf.local.home
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/arm
Fix for seldom hangs when bringing up arm32 cpu cores.
* tag 'v6.17-rockchip-arm32-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: fix kernel hang during smp initialization
Link: https://lore.kernel.org/r/12434765.CDJkKcVGEf@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Ftrace is tightly coupled with architecture specific code because it
requires the use of trampolines written in assembly. This means that when
a new feature or optimization is made, it must be done for all
architectures. To simplify the approach, CONFIG_HAVE_FTRACE_* configs are
added to denote which architecture has the new enhancement so that other
architectures can still function until they too have been updated.
The CONFIG_HAVE_FTRACE_MCOUNT was added to help simplify the
DYNAMIC_FTRACE work, but now every architecture that implements
DYNAMIC_FTRACE also has HAVE_FTRACE_MCOUNT set too, making it redundant
with the HAVE_DYNAMIC_FTRACE.
Remove the HAVE_FTRACE_MCOUNT config and use DYNAMIC_FTRACE directly where
applicable.
Link: https://lore.kernel.org/all/20250703154916.48e3ada7@gandalf.local.home/
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/20250704104838.27a18690@gandalf.local.home
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 device tree updates for v6.17
This update includes:
- controllers enabled for SAMA7D65 SoC (crypto controllers, PWM, CAN)
- controllers enabled for SAM9X7 SoC (LCD, LVDS)
- cache configuration updates for SAMA5D2, SAMA5D3, SAMA5D4, SAMA7G5,
SAMA7D65
- cleanups
* tag 'at91-dt-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (22 commits)
ARM: dts: microchip: sama7g5: Add cache configuration for cpu node
ARM: dts: microchip: sama7d65: Add cache configuration for cpu node
ARM: dts: microchip: sama5d4: Update the cache configuration for CPU
ARM: dts: microchip: sama5d3: Update the cache configuration for CPU
ARM: dts: microchip: sama5d2: Update the cache configuration for CPU
ARM: dts: microchip: sam9x7: Add LVDS controller
ARM: dts: microchip: sama5d2_icp: rename spi-cs-setup-ns property to spi-cs-setup-delay-ns
ARM: dts: microchip: sama5d27_wlsom1: rename spi-cs-setup-ns property to spi-cs-setup-delay-ns
ARM: dts: microchip: sama5d27_som1: rename spi-cs-setup-ns property to spi-cs-setup-delay-ns
ARM: dts: microchip: sam9x60ek: rename spi-cs-setup-ns property to spi-cs-setup-delay-ns
ARM: dts: at91-sama5d27_wlsom1: Improve the Wifi compatible
ARM: dts: microchip: gardena-smart-gateway: Fix power LED
ARM: dts: microchip: sam9x7: Add clock name property
ARM: dts: microchip: sama7d65: Add clock name property
ARM: dts: microchip: sama7g5: Adjust clock xtal phandle
ARM: dts: microchip: sam9x7: Add HLCD controller
ARM: dts: microchip: sama7d65: Enable CAN bus
ARM: dts: microchip: sama7d65: Clean up extra space
ARM: dts: microchip: sama7d65: Add CAN bus support
ARM: dts: microchip: sama7d65: Add PWM support
...
Link: https://lore.kernel.org/r/20250721100904.568575-2-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Common name for Ethernet controllers is "ethernet", not "eth", also
recommended by Devicetree specification in "Generic Names
Recommendation". Verified lack of impact using dtx_diff.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20250717142245.92492-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/defconfig
Microchip AT91 defconfig updates for v6.17
This update includes:
- the WILC1000 SDIO module
* tag 'at91-defconfig-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: configs: sama5_defconfig: Select CONFIG_WILC1000_SDIO
Link: https://lore.kernel.org/r/20250721100904.568575-1-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/defconfig
i.MX defconfig changes for 6.17:
- Enable S32G RTC driver as module in arm64 defconfig
- Enable drivers used by imx28-amarula-rmm board in mxs_defconfig
- Enable INPUT_PWM_BEEPER, USB_HSIC_USB3503 and BT_HCIUART_BCM in
imx_v6_v7_defconfig
* tag 'imx-defconfig-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: select CONFIG_USB_HSIC_USB3503
ARM: imx_v6_v7_defconfig: select CONFIG_INPUT_PWM_BEEPER
ARM: imx_v6_v7_defconfig: cleanup with savedefconfig
ARM: mxs_defconfig: select new drivers used by imx28-amarula-rmm
ARM: mxs_defconfig: Cleanup mxs_defconfig
arm64: defconfig: add S32G RTC module support
ARM: imx_v6_v7_defconfig: Select BT_HCIUART_BCM
Link: https://lore.kernel.org/r/20250713055441.221235-5-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the TPS65219 regulator in the defconfig, as the TPS65214
variant is used by the newly introduced BeagleBoard Green Eco board.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250620-bbg-v5-5-84f9b9a2e3a8@bootlin.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the TPS65219 regulator in the defconfig, as the TPS65214
variant is used by the newly introduced BeagleBoard Green Eco board.
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Tested-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250620-bbg-v5-4-84f9b9a2e3a8@bootlin.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt
mvebu dt for 6.17 (part 1)
Use recent scl/sda gpio bindings on kirkwood boards (Keymile ones)
* tag 'mvebu-dt-6.17-1' of https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: marvell: kirkwood: use recent scl/sda gpio bindings
Link: https://lore.kernel.org/r/87ms94xzr8.fsf@BLaptop.bootlin.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner device tree changes for 6.17
This branch includes a change shared with the clk tree for adding
the missing PPU0 reset on the A523.
The PM domain DT binding immutable branch is also included, which
brings in v6.16-rc2, as well as PM domain bindings for other platforms.
Other changes include:
- RGB666 LCD pin definitions for the V3s PE pins and V3 PD pins
- node order fixes for the A523 dtsi
- UART1 pin definitions for A523
- Allwinner board DT binding cleanup
- EMAC support on A100/A133
- Enabled on the Liontron H-A133L board
- SID efuse, power controllers and GPU added for A523
- A523 GPU enabled on all existing boards
New boards:
- Xunlong OrangePi 4A with the Allwinner T527 SoC.
* tag 'sunxi-dt-for-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
arm64: dts: allwinner: a523: enable Mali GPU for all boards
arm64: dts: allwinner: a523: add Mali GPU node
arm64: dts: allwinner: a523: Add power controller device nodes
dt-bindings: power: Add A523 PPU and PCK600 power controllers
arm64: dts: allwinner: A523: Add SID controller node
arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
arm64: dts: allwinner: a100: Add EMAC support
arm64: dts: allwinner: a100: Add pin definitions for RGMII/RMII
dt-bindings: arm: sunxi: Combine board variants into enums
dt-bindings: power: qcom,rpmpd: document the Milos RPMh Power Domains
arm64: dts: allwinner: t527: Add OrangePi 4A board
arm64: dts: allwinner: a523: Add UART1 pins
arm64: dts: allwinner: a523: Move rgmii0 pins to correct location
arm64: dts: allwinner: a523: Move mmc nodes to correct position
dt-bindings: arm: sunxi: Add Xunlong OrangePi 4A board
ARM: dts: sun8i: v3: Add RGB666 LCD PD pins definition
ARM: dts: sun8i: v3s: Add RGB666 LCD PE pins definition
dt-bindings: reset: sun55i-a523-r-ccu: Add missing PPU0 reset
dt-bindings: firmware: thead,th1520: Add resets for GPU clkgen
dt-bindings: rockchip: pmu: Add compatible for RK3528
...
Link: https://lore.kernel.org/r/aHaQFe3Lr8Qzyb1M@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm32 DeviceTree updates for v6.17
Add aliases for MMC controllers on MSM8974, enable USB charging on the
Sony Xperia Rhine platform and add new DeviceTree for the Sony Xperia Z
Ultra device.
Tidy up interrupts specifiers on MSM8960, by using macro constants.
* tag 'qcom-arm32-for-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974-sony-xperia-rhine: Add alias for mmc0 & mmc1
ARM: dts: qcom: msm8974-hammerhead: Add alias for mmc0
ARM: dts: qcom: msm8974-oneplus-bacon: Add alias for mmc0
ARM: dts: qcom: Add initial support for Sony Xperia Z Ultra (togari)
dt-bindings: arm: qcom: Add Sony Xperia Z Ultra (togari)
ARM: dts: qcom: msm8974-sony-xperia-rhine: Move camera buttons to amami & honami
ARM: dts: qcom: msm8974-sony-xperia-rhine: Enable USB charging
ARM: dts: qcom: msm8960: use macros for interrupts
ARM: dts: qcom: Align wifi node name with bindings
Link: https://lore.kernel.org/r/20250715021838.14751-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree changes for 6.17:
- New device trees for Engicam MicroGEA-MX6UL and i.MX28 Amarula board
- A couple of changes from Bence Csókás to replace license text comment
with SPDX identifier for Karo and Gateworks boards
- A couple of imx7s-warp updates from Fabio Estevam to improve Bluetooth
and Wifi description
- A set of dt-schema fixes for VF610 based boards from Frank Li
- A couple of imx6ul-kontron-sl-common changes to add SPI NOR partitions
and correct QSPI NAND node name
- A few other random improvements
* tag 'imx-dt-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (21 commits)
ARM: dts: imx6-gw: Replace license text comment with SPDX identifier
ARM: dts: imx6ul-kontron-sl-common: Fix QSPI NAND node name
ARM: dts: imx6ul-kontron-sl-common: Add SPI NOR partitions
ARM: dts: imx6ul-kontron-bl-common: Fix RTS polarity for RS485 interface
ARM: dts: imx6-karo: Replace license text comment with SPDX identifier
ARM: dts: imx6ul: support Engicam MicroGEA GTW board
ARM: dts: imx6ul: support Engicam MicroGEA RMM board
ARM: dts: imx6ul: support Engicam MicroGEA BMM board
ARM: dts: imx6ul: support Engicam MicroGEA-MX6UL SoM
ARM: dts: mxs: support i.MX28 Amarula rmm board
ARM: dts: imx28: add pwm7 muxing options
ARM: dts: vf: vf610-zii-cfu1: rename node name *-gpio to *-gpios
ARM: dts: vf: vf-colibri-eval-v3: add power-supply for edt,et057090dhu
ARM: dts: vf: rename io-expander@20 to pinctrl@20
ARM: dts: vf: remove redundant layer under iomux
ARM: dts: vf: remove redundant pinctrl-names
ARM: dts: vf: remove reg property for arm pmu
ARM: dts: vfxxx: Correctly use two tuples for timer address
ARM: dts: add ngpios for vf610 compatible gpio controllers
ARM: dts: imx7s-warp: Improve the Wifi description
...
Link: https://lore.kernel.org/r/20250713055441.221235-3-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
ARM: tegra: Device tree changes for v6.17-rc1
Add support for two Tegra30 ASUS devices and enable the embedded
controller on Pegatron Chagall.
* tag 'tegra-for-6.17-arm-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: chagall: Add embedded controller node
ARM: tegra: Add device-tree for Asus Portable AiO P1801-T
ARM: tegra: Add device-tree for ASUS VivoTab RT TF600T
Link: https://lore.kernel.org/r/20250711220943.2389322-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/arm
mvebu arm for 6.17 (part 1)
Use string choices helper in GPIO support code for legacy Orion based
platforms.
* tag 'mvebu-arm-6.17-1' of https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm: orion: use string choices helper
Link: https://lore.kernel.org/r/87jz48xzpz.fsf@BLaptop.bootlin.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/arm
ARM: tegra: Core changes for v6.17-rc1
Fixes an issue when copying data to IRAM using memcpy() and use the
memcpy_toio() function instead.
* tag 'tegra-for-6.17-arm-core' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Use I/O memcpy to write to IRAM
Link: https://lore.kernel.org/r/20250711220943.2389322-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/arm
MediaTek mach ARM32 updates
This adds support for the MediaTek MT6572 SoC, found in various
old smartphones and tablets from various manufacturers.
In particular, this adds a board_dt_compat entry for this SoC
and its SMP bring up sequence to enable secondary cores.
* tag 'mtk-arm32-for-v6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
ARM: mediatek: add MT6572 smp bring up code
ARM: mediatek: add board_dt_compat entry for the MT6572 SoC
Link: https://lore.kernel.org/r/20250711083656.33538-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The conversion to using the new GPIO line setter callbacks missed the
set_multiple() in this file. Convert it to using the new callback.
Fixes: 9c3782118a57 ("ARM: sa1100/gpio: use new line value setter callbacks")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When KCOV is enabled all functions get instrumented, unless
the __no_sanitize_coverage attribute is used. To prepare for
__no_sanitize_coverage being applied to __init functions, we have to
handle differences in how GCC's inline optimizations get resolved. For
arm this exposed several places where __init annotations were missing
but ended up being "accidentally correct". Fix these cases and force
several functions to be inline with __always_inline.
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20250717232519.2984886-5-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
In preparation for Clang stack depth tracking for KSTACK_ERASE,
split the stackleak-specific cflags out of GCC_PLUGINS_CFLAGS into
KSTACK_ERASE_CFLAGS.
Link: https://lore.kernel.org/r/20250717232519.2984886-3-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
In preparation for adding Clang sanitizer coverage stack depth tracking
that can support stack depth callbacks:
- Add the new top-level CONFIG_KSTACK_ERASE option which will be
implemented either with the stackleak GCC plugin, or with the Clang
stack depth callback support.
- Rename CONFIG_GCC_PLUGIN_STACKLEAK as needed to CONFIG_KSTACK_ERASE,
but keep it for anything specific to the GCC plugin itself.
- Rename all exposed "STACKLEAK" names and files to "KSTACK_ERASE" (named
for what it does rather than what it protects against), but leave as
many of the internals alone as possible to avoid even more churn.
While here, also split "prev_lowest_stack" into CONFIG_KSTACK_ERASE_METRICS,
since that's the only place it is referenced from.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250717232519.2984886-1-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/dt
MediaTek mach ARM32 updates
This adds support for the MediaTek MT6572 SoC, found in various
old smartphones and tablets from various manufacturers.
In particular, this adds a board_dt_compat entry for this SoC
and its SMP bring up sequence to enable secondary cores.
* tag 'mtk-dts32-for-v6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
ARM: dts: mediatek: add basic support for Lenovo A369i board
ARM: dts: mediatek: add basic support for JTY D101 board
ARM: dts: mediatek: add basic support for MT6572 SoC
dt-bindings: arm: mediatek: add boards based on the MT6572 SoC
dt-bindings: vendor-prefixes: add JTY
dt-bindings: watchdog: mediatek,mtk-wdt: add MT6572
dt-bindings: interrupt-controller: mediatek,mt6577-sysirq: add MT6572
Link: https://lore.kernel.org/r/20250711083656.33538-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap into soc/dt
arm: dts: OMAP updates for v6.17
- new board support: Seeed BeagleBone Green Eco
- misc. fixups / cleanups
* tag 'omap-for-v6.17/dt-signed' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap:
arm: dts: ti: omap: Fixup pinheader typo
ARM: dts: am335x-pdu001: Fix RS-485 transceiver switching
arm: dts: omap: Add support for BeagleBone Green Eco board
dt-bindings: omap: Add Seeed BeagleBone Green Eco
arm: dts: omap: am335x-bone-common: Rename tps to generic pmic node
Revert "ARM: dts: Update pcie ranges for dra7"
ARM: dts: omap: am335x: Use non-deprecated rts-gpios
Link: https://lore.kernel.org/r/7h7c0gxczy.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.17, round 1
Highlights:
----------
- MPU:
- STM32MP13:
-Add Ethernet MAC adress efuse support.
- STMP32MP15:
- Add stm32mp157f-DK2 board support. This board embedds the same
conectivity devices, DDR ... than stm32mp157c-dk2.
However there are two differences: STM32MP157F SoC which allows
overdrive OPP and the SCMI support for system features like
clocks and regulators.
- STM32MP25:
- Fix tick timer for low power use cases.
- Add timer support.
* tag 'stm32-dt-for-v6.17-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
arm64: dts: st: remove empty line in stm32mp251.dtsi
arm64: dts: st: fix timer used for ticks
arm64: defconfig: Enable STM32 Octo Memory Manager and OcstoSPI driver
ARM: dts: stm32: add stm32mp157f-dk2 board support
dt-bindings: arm: stm32: add STM32MP157F-DK2 board compatible
ARM: dts: stm32: optee async notif interrupt for MP15 scmi variants
ARM: dts: stm32: use internal regulators bindings for MP15 scmi variants
dt-bindings: regulator: Add STM32MP15 SCMI regulator identifiers
ARM: dts: stm32: use 'typec' generic name for stusb1600 on stm32mp15xx-dkx
ARM: dts: stm32: fullfill diversity with OPP for STM32M15xF SOCs
ARM: dts: stm32: add system-clock-direction-out on stm32mp15xx-dkx
arm64: defconfig: enable STM32 timers drivers
arm64: dts: st: add timer nodes on stm32mp257f-ev1
arm64: dts: st: add timer pins for stm32mp257f-ev1
arm64: dts: st: add timer nodes on stm32mp251
ARM: dts: stm32: Add nvmem-cells to ethernet nodes for constant mac-addresses
Link: https://lore.kernel.org/r/b3e3363b-1ea5-457c-b244-2cbe26f7d6e4@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bmc/linux into soc/dt
ASPEED devicetree updates for 6.17
Removed platforms:
- IBM's Swift BMC
New platforms:
- Meta's Santabarbara
Santabarbara is a compute node with an accelerator module
- NVIDIA's GB200NVL BMC
NVIDIA GB200 NVL72 connects 36 Grace CPUs and 72 Blackwell GPUs in an NVIDIA
NVLink-connected, liquid-cooled, rack-scale design.
Updated BMC platforms:
- Bletchley (Meta): GPIO hog names, remove ethernet-phy node, USB PD negotiation
- Catalina (Meta): Various sensors added, MCTP support for NIC management
- Harma (Meta): Various sensors added
- System1 (IBM): IPMB and various GPIO-related updates
- Yosemite4 (Meta): GPIO names for UART mux select lines
The System1 series includes a devicetree binding patch for IPMI IPMB devices.
* tag 'aspeed-6.17-devicetree-1' of https://git.kernel.org/pub/scm/linux/kernel/git/bmc/linux: (34 commits)
ARM: dts: aspeed: yosemite4: add gpio name for uart mux sel
ARM: dts: aspeed: santabarbara: Add Meta Santabarbara BMC
dt-bindings: arm: aspeed: add Meta Santabarbara board
ARM: dts: aspeed: bletchley: enable USB PD negotiation
ARM: dts: aspeed: lanyang: Fix 'lable' typo in LED nodes
ARM: dts: aspeed: harma: add mmc health
ARM: dts: aspeed: Harma: revise gpio bride pin for battery
ARM: dts: aspeed: harma: add ADC128D818 for voltage monitoring
ARM: dts: aspeed: harma: add fan board I/O expander
ARM: dts: aspeed: harma: add E1.S power monitor
ARM: dts: aspeed: catalina: Enable MCTP for frontend NIC management
ARM: dts: aspeed: Add device tree for Nvidia's GB200NVL BMC
dt-bindings: arm: aspeed: add Nvidia's GB200NVL BMC
ARM: dts: aspeed: catalina: Enable MCTP support for NIC management
ARM: dts: aspeed: catalina: Update CBC FRU EEPROM I2C bus and address
ARM: dts: aspeed: catalina: Enable multi-master on additional I2C buses
ARM: dts: aspeed: catalina: Remove INA238 and INA230 nodes
ARM: dts: aspeed: catalina: Add second source HSC node support
ARM: dts: aspeed: catalina: Add second source fan controller support
ARM: dts: aspeed: catalina: Add fan controller support
...
Link: https://lore.kernel.org/r/36d50489cac1fbae01ec699b742f6c6c459a01cb.camel@codeconstruct.com.au
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM changes for v6.17
Just few cleanups based on dtbs_check.
* tag 'samsung-dt-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5pv210: Align i2c-gpio node names with dtschema
ARM: dts: exynos: Align i2c-gpio node names with dtschema
Link: https://lore.kernel.org/r/20250709191523.171359-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
VT8500 DTS ARM changes for v6.17
1. Several dtbs_check cleanups.
2. Add missing cache topology - L2 cache controller on WM8850/WM895.
* tag 'dt-vt8500-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: vt8500: Add L2 cache controller on WM8850/WM8950
ARM: dts: vt8500: Fix the unit address of the VT8500 LCD controller
ARM: dts: vt8500: Use generic node name for the SD/MMC controller
ARM: dts: vt8500: Move memory nodes to board dts and fix addr/size
ARM: dts: vt8500: Add node address and reg in CPU nodes
Link: https://lore.kernel.org/r/20250709184800.168462-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm into sunxi/dt-for-6.17
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
