| Age | Commit message (Collapse) | Author |
|---|
|
Hwmod parses the DT hierarchically from root to search for matching
ti,hwmod property. With the introduction of L4 data, we have two nodes
with the ti,hwmod = "gmac" declaration, and the hwmod core only matches
the first one found, which is the target-module one. This node incorrectly
dropped the ti,no-idle flag, which causes number of problems, like ignoring
errata i877, and also causing an intermittent boot failure on certain dra7
boards.
Fix the issue by moving the ti,no-idle flag to the proper node.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Without this McASP FIFO would constantly underflow. EDMA
test via dmatest works though.
Let's revert the change for now until we know the root cause.
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Video Image Compositor can be used to perform a variety of image
operations. Add a device tree node for it, so that it can be exposed
as a host1x channel to userspace.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This updates the Versatile defconfig to use the new P111 DRM
driver that is merged in the DRM subsystem.
We deactivate the old CLCD driver and activate the Pl111 DRM
driver and the SiI9022 HDMI bridge.
We activate DMA memory allocation using CMA so that the special
graphics memory for the on-board CLCD can be used.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Update the Versatile Express defconfig to match the
Kconfig changes in the kernel.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Versatile Express was submitted with the actual display
bridges unconnected (but defined in the device tree) and
mock "panels" encoded in the device tree node of the PL111
controller.
This doesn't even remotely describe the actual Versatile
Express hardware. Exploit the SiI9022 bridge by connecting
the PL111 pads to it, making it use EDID or fallback values
to drive the monitor.
The also has to use the reserved memory through the
CMA pool rather than by open coding a memory region and
remapping it explicitly in the driver. To achieve this,
a reserved-memory node must exist in the root of the
device tree, so we need to pull that out of the
motherboard .dtsi include files, and push it into each
top-level device tree instead.
We do the same manouver for all the Versatile Express
boards, taking into account the different location of the
video RAM depending on which chip select is used on
each platform.
This plays nicely with the new PL111 DRM driver and
follows the standard ways of assigning bridges and
memory pools for graphics.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Meson Timer IP block has two clock inputs:
- clk81 for using the system clock as timebase
- xtal for a timebase with 1us, 10us, 100us and 1ms resolution
The clocksource driver does not use these yet, but it's still a good
idea to add them as this describes how the hardware actually works
internally.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The timer on Meson6/Meson8/Meson8b SoCs has four internal timer events.
For each of these a separate interrupt exists.
Pass these interrupts to allow using the timers other than TIMER A.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
On Amlogic chipsets, the bias set through pinconf applies to the pad
itself, not only the GPIO function. This means that even when we change
the function of the pad from GPIO to anything else, the bias previously
set still applies.
As we have seen with the eMMC, depending on the bias type and the function,
it may trigger problems.
The underlying issue is that we inherit whatever was left by previous user
of the pad (pinconf, u-boot or the ROM code). As a consequence, the actual
setup we will get is undefined.
There is nothing mentioned in the documentation about pad bias and pinmux
function, however leaving it undefined is not an option.
This change consistently disable the pad bias for every pinmux functions.
It seems to work well, we can only assume that the necessary bias (if any)
is already provided by the pin function itself.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch removes support for the APQ8064 based Arrow SD600 eval
board. This board was never sold publicly and had very limited
distribution. As such, we are removing this board and no longer
going to support it.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
|
|
As per upstream discussion [1], we should have an SoC-specific
compatible string for Qualcomm's SDHCI nodes. Let's add it.
[1] https://lkml.kernel.org/r/20181105203657.GA32282@bogus
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch correctly sets the gpios property for the ak8963
magnetometer's DRDY pin so that interrupts work properly.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
In two of the gen5 socfpga devicetree files, there are some lines
indented using spaces instead of tabs.
Fix this by correctly indenting them with tabs.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The dma-mask property has been removed from the NAND driver. Remove the
property from the DTS files.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Follow the recent trend for the license description.
This is also in an effort to fully sync the devicetrees with U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Turn on these ARM and PL310 errata for SoCFPGA:
ARM_ERRATA_754322
ARM_ERRATA_764369
ARM_ERRATA_775420
PL310_ERRATA_588369
PL310_ERRATA_727915
PL310_ERRATA_753970
PL310_ERRATA_769419
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
These functions are unused externally, removed them and declare
the one used locally as static.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Cyclone5 and Arria10 doesn't have the same memory map for UART1.
Split the SOCFPGA_UART1 into 2 options to allow debugging on UART1 for Cyclone5.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Our memory node will generate a warning in DTC since the unit address is
not matching the reg property. However, that node will be created by the
bootloader, so we can just remove it entirely in order to remove that
warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The MMC0 controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The i2c nodes were pre-populated to ease the use of overlays. However, now
that we provide default muxing options for those nodes, the one in the DTS
don't provide any content at all.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that all the SoCs using the tablet reference design DTSI are using the
same pinctrl naming scheme, we can move back the pinctrl phandles to the
main DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The pin groups are supposed to be in alphabetical order, and they aren't.
Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
DTC will emit a warning on our OPPs nodes for the common DTSI between the
A23 and A33 since those nodes use the frequency as unit addresses, but
don't have a matching reg property.
Fix this by moving the frequency to the node name instead.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The SOM204-EVB doesn't use the CTS pin, and thus was defining its own
pinctrl node for the UART3 muxing. Since we split away the TX and RX pin,
we can use the global node now, and only have the RTS pin in our local
node.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some UART nodes on the A20 DTSI do not share the same pattern that we use
everywhere else, with the RTS and CTS pins split away from the TX and RX
pins. Make those pin groups consistent with the rest of our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some gpio-keys definitions in our DTs were having buttons defined with a
unit-address and that would generate a DTC warning.
Change the buttons node names to remove the warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
